Index - Ithaca 150 Programmer's Manual

Programmer's Guide

Index

—[—
[CAN] Clear print buffer........................................ 54
[CR] New line ....................................................... 15
[DC2] Set 10 cpi.................................................... 31
[DC4] End one-line double-wide............................ 33
[ENQ] <1> Inquire Cash Drawer 1 status............... 60
[ENQ] <10> Request printer reset.......................... 62
[ENQ] <11> Request printer power-cycle status..... 62
[ENQ] <2> Inquire Cash Drawer 2 status............... 60
[ENQ] <4> Inquire receipt-paper out status............ 60
[ENQ] <6> Inquire form position sensor status....... 61
[ENQ] <7> Inquire form-clamp status .................... 61
[ENQ] <9> Send response ..................................... 61
[ENQ] <n> Inquire printer status ........................... 60
[ESC] - <0> End underline .................................... 35
[ESC] - <1> Begin underline ................................. 35
[ESC] ! <n> Select international character set ........ 24
[ESC] # <0> Begin High Speed Draft Mode........... 22
[ESC] $ Copy ROM Character Set to RAM Character
Set .................................................................... 28
[ESC] % G Begin italics ........................................ 37
[ESC] % H End italics ........................................... 38
1 2
[ESC] * <m> <n> <n> Print graphics in mode <m>
......................................................................... 45
[ESC] \: Set 12 cpi ................................................. 31
[ESC] ? <m><n> Reassign graphics mode.............. 45
[ESC] [ @ ... Double-high, double-wide, and italic 34
[ESC] [ C <n> Insert Euro Character...................... 29
[ESC] [ P <n> Set cpi ............................................ 32
[ESC] [ S <L > <L > <B > ... Redefine Character
L H C
Set .................................................................... 27
[ESC] [ T <n h > <n l > Select Character Code Page .. 26
[ESC] [DC1] Open forms clamp............................. 51
[ESC] [DC3] Close forms clamp ............................ 51
[ESC] [DC4] Select validation mode ...................... 51
[ESC] [EM] B 0 Bar code height............................ 49
[ESC] [EM] C <0> Validation clamp delay ............ 52
[ESC] [EM] J <n> Bar code justification................ 49
[ESC] [EM] V <n> Set validation delay ................. 52
[ESC] [SI] Set 24 cpi ............................................. 31
[ESC] ] Reverse line feed....................................... 21
[ESC] ^ <n> Print control character ....................... 27
[ESC] _ <0> End overscore.................................... 35
[ESC] _ <1> Begin overscore................................. 35
[ESC] ~ <n> Extended diagnostics......................... 66
[ESC] < <n> Pass through...................................... 56
[ESC] < <n> Print suppress ................................... 56
[ESC] = <c1><c2><start code><data> Character
download........................................................... 28
[ESC] > <0> Custom character set OFF ................. 29
[ESC] > <1> Custom character set ON................... 28
[ESC] 0 Set line space to 27/216 inch .................... 18
[ESC] 1 Set line spacing 7/72 inch......................... 19
12/14/99
PcOS Series 150
[ESC] 2 Enable variable line spacing......................19
[ESC] 3 <n> Set line spacing in n/216 inch ............18
[ESC] 4 Set top of form..........................................20
[ESC] 5 <0> End auto line feed..............................21
[ESC] 5 <1> Begin auto line feed ...........................21
[ESC] 8 Disable PE sensor .....................................50
[ESC] 9 Enable PE sensor ......................................50
[ESC] a <n> Set justification..................................17
[ESC] A <n> Set variable line spacing n/72 inch ....19
[ESC] b <n> ... Print bar code ................................47
[ESC] B <n>1 <n>2 Set vertical tab stops ..............20
[ESC] C Set form length........................................21
[ESC] C [NUL] Set form length.............................21
[ESC] d <n> Enable variable line spacing...............19
[ESC] D <n>1 <n>2 Set horizontal tab stops ..........16
[ESC] E Begin emphasized print ............................36
[ESC] F End emphasized print ...............................36
[ESC] G Begin enhanced print ...............................36
[ESC] H End enhanced print ..................................36
[ESC] I <1> Set Utility Print Mode ........................22
[ESC] J <n> Fine line feed .....................................18
[ESC] K <n>
[ESC] L <n>
[ESC] P <0> Reset 90 rotated font ........................23
[ESC] P <1> Set 90 rotated font............................23
[ESC] P <2> Set 270 rotated font..........................23
[ESC] q <n> Query marker.....................................55
[ESC] r <0> End rotated print ................................42
[ESC] r <1> Rotate 90° ..........................................40
[ESC] r <2> Rotate 180° ........................................41
[ESC] r <3> Rotate 270° ........................................41
[ESC] r <5> Rotate 90° with line formatting...........40
[ESC] r <7> Rotate 270° with formatting................41
[ESC] R Reset horizontal tab stops .........................17
[ESC] s <n> Set rotated print line length ................42
[ESC] S<0> Select superscript ...............................37
[ESC] S<1> Select subscript ..................................37
[ESC] T End superscript or subscript......................37
[ESC] U <0> Begin bidirectional print ...................46
[ESC] U <1> Begin unidirectional print .................46
[ESC] u <n
[ESC] V <n> Set intercharacter spacing..................32
[ESC] W <n> Double-wide and double-high...........34
[ESC] w <n> Enable dynamic response ..................57
[ESC] x <n> Open cash drawer ..............................54
[ESC] X <n1> <n2> Set left/right margin ...............53
[ESC] y <n> Feature control...................................56
[ESC] Y <n>
graphics .............................................................44
[ESC] Z <n>
[ESC]v Activate cutter............................................57
[FF] Form feed.......................................................20
[HT] Horizontal tab................................................16
[LF] Line feed........................................................15
[SI] Set 17 cpi ........................................................31
Rev G
1 2
<n> Print single-density graphics ....44
1 2
<n> Print double-density graphics ...44
> <m >... Set rotated print line spacing43
1 1
1 2
<n> Print full-speed double-density
1 2
<n> Print quad-density graphics ......45
Index
Page 137