Display Machine Data For Shopturn - Siemens SINUMERIK 840D sl Commissioning Manual

11/2006
7.2

Display machine data for ShopTurn

7.2.1 Overview of display machine data
MD MD identifier
No.
9014 $MM_USE_CHANNEL_DISPLA Y_DATA
9020 $MM_TECHNOLOGY
9422 $MM_MA_PRESET_MODE
9428 $MM_MA_SPIND_MAX_POWER
9429 $MM_MA_SPIND_POWER_RANGE
9450 $MM_WRITE_TOA_FINE_LIMIT
9451 $MM_WRITE_ZOA_FINE_LIMIT
9460 $MM_PROGRAM_SETTINGS
9478* $MM_TO_OPTION_MASK
9550* $MM_CTM_CYC_ROUGH_RELEASE_DIST
9551* $MM_CTM_CYC_ROUGH_RELEASE_ANGLE
9552* $MM_CTM_CYC_ROUGH_BLANC_OFFS
9553* $MM_CTM_CYC_ROUGH_TRACE_ANGLE
9554 $MM_CTM_CYC_ROUGH_MIN_REST_MA T_1
9555 $MM_CTM_CYC_ROUGH_MIN_REST_MA T_2
9556 $MM_CTM_CYC_ROUGH_V AR_DEPTH
9557 $MM_CTM_CYC_ROUGH_FEED_INT_TIME
9558 $MM_CTM_CYC_ROUGH_INT_REL_DIST
9560 $MM_CTM_TURN_GROOV_T OOL_BEND
9561 $MM_CTM_TURN_GROOV_FREE_CUT_V AL
9606 $MM_CTM_SIMULA TION_TIME_NEW_POS
9611 $MM_CTM_CROSS_AX_DIAMETER_ON
9619 $MM_CTM_G91_DIAMETER_ON
9621 $MM_CTM_CYCLE_DWELL_TIME
9626 $MM_CTM_TRACE
9630 $MM_CTM_FIN_FEED_PERCENT
9639 $MM_CTM_MAX_T OOL_WEAR
9640 $MM_CTM_ENABLE_CALC_THREAD_PITCH
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D sl Commissioning Manual CNC: ShopTurn – 11/2006 Edition
Once ShopTurn has been installed on the PCU and commissioning of the NCK
and PLC is complete, you still need to adapt the display machine data.
In any case, you must check the settings
of the display machine data that are identified in table 7-1 by means of "*".
Table 7-1 Display machine data for ShopTurn
7.2 Display machine data for ShopTurn
Comments
Use channel–specific display machine
data
Basic configuration turning/milling
Preset/basic offset in JOG
Factor for display of spindle utilization
Display area for spindle utilization
Limit value for wear fine
Limit value for fine adjustment
Settings in the Program area
Settings for ShopTurn
Retraction distance for stock removal at a
contour
Retraction angle for stock removal at a
contour
Blank offset for stock removal at a contour
Starting angle for tracing a contour
Starting thickness, with reference to the
final machining allowance, for machining
residual material (axis 1)
Starting thickness, with reference to the
final machining allowance, for machining
residual material (axis 2)
Percentage for variable cutting depth when
turning a contour
Feed interruption time when turning a con-
tour
Retraction path feed interruption Kontur-
drehen
Retraction due to tool bending when
plunge–turning a groove
Retraction depth before turning operation
when plunge–turning a groove
Simulation updating rate of actual value
Diameter display for active transverse
axes
Incremental infeed
Dwell time for cycles
Settings for ShopTurn
Finishing feed in percent
Upper input limit for tool wear
Calculation of thread depth if pitch entered
7 Machine Data
Preset
default
0
1
1
100
200
0.999
0.999
HD
1
1
45
1
5
50
50
20
–1
0
0.1
0.1
350
1
0
–1
1
100
1
0
7-43