External Leslie Speaker - Hammond XK-5 Owner's Manual

Th e setting range is 0, 24 to 318 rpm.
❺ / ⓮ FAST SPEED - HORN / DRUM (L)
Sets the rotor speed on the Fast mode.
Th e setting range is 0, 375 to 453 rpm.
❻ / ⓯ RISE TIME - HORN / DRUM (L)
Sets the time for the rotors to "ramp up" to the 'Fast Speed',when
switching from 'Slow' or 'Stop' to the 'Fast' mode.
Th e setting range for the Horn rotor is 0.2 to 5.0 sec., and the
Bass rotor is 0.5 to 12.5 sec.
❼ / ⓰ FALL TIME - HORN / DRUM (L)
Sets the time for the rotor to reach the 'Slow Speed', when
switching from 'Fast' to 'Slow' mode.
Th e setting range for the Horn rotor is 0.2 to 5.0 sec., and the Bass rotor is 0.5 to 12.5
sec.
❽ / ⓱ BRAKE TIME - HORN / DRUM (L)
Sets the time for the rotor to stop, when switching from 'Fast' to the 'Stop' mode.
Th e setting range for the Horn rotor is 0.2 to 5.0 sec., and the Bass rotor is 0.5 to 12.5
sec.
❾ / ⓲ DELAY TIME - HORN / DRUM (L)
Sets the time for operation to begin the 'Rise time'.
Th e setting range is 0 to 0.8 sec.
❿ / ⓳ MIC WIDTH - HORN / DRUM (L)
Th ese mic parameters sets the locating the microphones for virtual Leslie speaker (see
right fi gure).
Th is 'width' sets the horizontal interval of the two microphones. Th e setting range is 0 to
40. Th e value increases makes wider stereophonic. At 0, mono.
⓫ / ⓴ MIC CENTER - HORN / DRUM (L)
Sets the off set between center of two microphones and pivot of the rotor.
Th e setting range is -50 to +50 cm. Th e virtual Leslie speaker turns counter
clockwise for Horn rotor, and clockwise for Drum rotor. To emphasize the
'upcoming', set the '+' value for Horn rotor, and '-' value for Drum rotor.
⓬ /
MIC DISTANCE - HORN / DRUM (L)
Sets the distance between the virtual Leslie speaker and microphones.
Th e setting range is 30 to 200 cm. Th e value decreases makes deeper eff ect.
/ /
LEVEL - SUB BASS / DRUM / HORN (L)
Sets the volume levels of the each rotor and the sub bass which does not
modulated by the Drum rotor.
Th e setting range is -12 to 0 dB.
CROSSOVER
Set the crossover frequency between sub bass and the Drum rotor.
Th e setting range is 20 to 250 Hz. Th e value decreases makes whole range
of the modulation.
NOTE: The parameters #2 to #25 are Leslie parameters. These are common for same Custom
Cabinet of each Patch.
NOTE: After editing, you must record your changes to save them (Procedure following).

EXTERNAL LESLIE SPEAKER

LESLIE CHANNELS
Sets the channel for the Leslie speaker connected to the LESLIE 11-PIN jack.
1ch: For connecting a 1 channel Leslie cabinet such as the #981/#3300/#122XB. The Drawbar and
the percussion sounds are output only from the rotary channel always. The Pipe voices are
from the LINE OUT jack.
Mode: SLOW FAST
Rotor
Speed:
Rise
Delay
Time
Time
Horn Rotor
Drum Rotor
SLOW FAST STOP
Fall Brake
Time Time
Sub Bass
87