Extron electronics FOX Matrix 320x User Manual page 33

Command and Response Table for SIS Commands (continued)
Command SIS Command
(Host to Unit)
Reclocking
NOTES:
• Laser board reclockers are set on a per SFP basis. If an SFP is reclocked, the corresponding input and output reclockers reclock at
the same rate.
• HD-SDI reclockers are set on a per output basis only.
• If the connected input or output device is a FOX USB Extender unit, ensure that the re-clockers are set to bypass mode.
X$
Set output reclocker
Example:
8*00=
X$
Read reclocker status
Laser controls
Enable individual laser EX@
driver
EX@
Disable individual laser driver
EX@
Set individual output laser
driver to automatic
E
Read status of all laser
drivers
E
Global laser enable
NOTE: If your switcher has any BNC 3G/HD/SD-SDI boards installed, the global commands are not available. The switcher returns E14.
Global laser disable E
E
Global laser automatic
Save, recall, and directly write presets
NOTES:
• If you try to recall a preset that is not saved, the matrix switcher responds with the error code E11.
• The following characters are invalid or not recommended in preset names: + - , ` @ = [ ] { } ' " ; : | \ and ?.
X&
Save current configuration
as a global preset
Example:
9,
Recall a global preset X&
Example: 5.
Direct write process
NOTE: The direct write of a global preset should always be preceded by a clear global preset ties command of that same preset number.
In a directly-written preset, the tied input of each output position (or no tied input) remains unchanged unless overwritten or cleared.
If you do not clear the ties in a global preset number before you directly write a global preset to that number, ties that are part of the
previous version of the specified preset with the same number can unexpectedly become part of the newly-created preset.
Clear ties of a global preset E
E
Directly write a global
preset
E
Example:
Esc
KEY: X! = Input number
X@ = Output number
X$ = SFP or reclockable output 000 – 144 or 320 (FOX Matrix 320x) (000 = global [SFP only])
X% = Output reclocking rate
X^ = Laser control
X&
= Global preset number
Response
(Unit to Host)
X% X$
* = Rte
Rte08*00
X%]
=
}
*1FIBR Fibr
}
*0FIBR Fibr
}
*2FIBR Fibr
} X^ X^
FIBR
1
}
Fibr1 ]
1*FIBR
}
Fibr0 ]
0*FIBR
}
Fibr2 ]
2*FIBR
X&]
, Spr
Spr9
X&]
. Rpr
Rpr05
X& } X&]
+ P0*! Spr
X& X! X@ X! X@ X! X@ X!
! ...
+ P * ! * % *
X&]
Spr
}
+27P0*! Spr27
+27P12*5!10*09%3*2!3*8&
Spr27
0 00 – (maximum number of inputs for your configuration) (000 = untied)
001 – (maximum number of outputs for your configuration)
00 = Bypass mode
01 = Automatic mode (HDSDI [default] only) or N/A (laser)
02 = 1.250 Gbps (laser boards only)
0 = disable
00 – 64
FOX Matrix 320x and FOX Matrix 14400 • Programming Guide
Additional description
X%]
Set the rate for reclocker
*
]
Set the rate for reclocker 8 to bypass.
Show current rate status for reclocker
X@ ]
Enable the laser for output
*1
so long as power is applied.
X@ ]
*0 Disable the laser for output
X@ ]
Set the laser driver for output
*2
The laser lights when a tie is made to output
X@
, but is off when no tie is made to output
or the output is muted.
X^ X^ X^ ]
... List the laser driver status of all installed outputs.
2 3 4 n
n is the highest numbered output for your switcher.
Enable all output laser drivers.
Disable all output laser drivers.
Set all output laser drivers to automatic.
Command character is a comma.
]
Save current ties as preset 9.
Command character is a period.
]
Recall preset 5, to become the current configuration.
Clear all ties in preset
X@ }
Enter as many ties as are valid for this configuration.
* %
!
The tie,
] Clear all ties in preset 27.
Brackets are shown to separate ties for clarity
only. Create global preset 27, which ties
]
input 12 to output 5, input 10 to output 9,
input 3 to output 2, and input 3 to output 8.
1 = enable (default)
X$ X%
to .
X$
.
X@
. The laser lights
X@
. The laser is off.
X@
to automatic.
X&
.
& %
tie, and tie commands are all valid.
03 = 2.125 Gbps (laser only)
04 = 4.250 Gbps (laser only [default])
2 = automatic
X@
26