Extron electronics FOX Matrix 320x User Manual page 34

Command and Response Table for SIS Commands (continued)
Command SIS Command
(Host to Unit)
Save, recall, and directly write presets (continued)
NOTES:
• A room can contain a maximum of 16 outputs (
• If a room is not defined (does not exist in the switcher), the matrix switcher responds with the error code E11.
• An output can belong to only one room.
• The maximum number of rooms (
EX*
Write room outputs
E
Example:
EX*
Read room outputs
NOTES:
• If no outputs have been assigned to the room, the switcher returns [unassigned]
X(
• The default name ( ) is the room number with four trailing spaces: " Room • #
E
Example:
X*
Save ties as a room preset
NOTE: You must have assigned outputs to a room (
Example:
3*9,
X*
Recall room preset
E
Clear room preset ties
E
Directly write a room preset
Example:
Esc
View ties, mutes, and presets
NOTE: The ! read tie command, & read tie command, and % read tie command can be used interchangeably.
X@
View tied input
X@
View output tie
Example:
15&
X@
View output tie
Example:
7%
View output mutes E
NOTE: The switcher reports the mute status for all outputs, up to the highest numbered output on the highest numbered slot with an
I/O board installed. The switcher does not recognize gaps in the board installation. For example, if boards are installed in only slots 1
and 3, leaving slot 2 empty, the switcher returns mute status for 48 sequential outputs. The mute status for the outputs in slot 2, inputs
17 through 32, can be ones or zeroes (the switcher allows you to mute an output that is not installed, so long as it is numbered lower
than the highest numbered output installed).
KEY: X! = Input number
X@ = Output number
X# = Mute
X* = Room # (for room presets)
X1) = Room preset #
Response
(Unit to Host)
X@
s).
X*
) is 10.
X@ X@ X@ } X*
, ...
, , MR Mpr
1 2 n
}
8,3,04,5,6MR Mpr8,03,04,05,06
} X( X@
MR ,
}
3MR Room • #03 •••• ,01,02,08,09
X1) X*
* , Rmm
EX* }
, MR
Rmm03 • Spr09
X1) X*
* . Rmm
X* X1) } X*
+ * P0*! Rmm
X* X1) X! X@ X! X@ X! X@
+ * P * ! * % * ! ...
X*
Rmm
+7*3P12*7&11*5&4*5%6*6!
Rmm07 • Spr03
X!]
!
X!]
&
]
027
X!]
%
]
002
} X# X#
VM 1
000 – (maximum number of inputs for your configuration) (000 = untied)
001 – (maximum number of outputs for your configuration)
0 = not muted;
01 – 10 (each can have up to 10 presets (
01 – 10
FOX Matrix 320x and FOX Matrix 14400 • Programming Guide
Additional description
X@ X@ X@ ]
, ... See the notes below.
, ,
1 2 n
]
Outputs 3, 4, 5, and 6 are assigned to room 8.
X@ X@ ]
, , ...
1 2 n
]
.
X*
••••".
]
Outputs 1, 2, 8, and 9 are assigned to room 3.
X1)]
Command character is a comma.
• Spr
) before you can save a room preset.
]
Save current ties as preset 9 for room 3.
X1)]
Command character is a period.
• Rpr
X1)]
• Spr Clear all ties in room
X! X@ }
Enter as many ties as are valid for this
* !
configuration. The ! tie command, & tie, and %
X1)]
• Spr
tie commands are all valid and equivalent.
Brackets are shown to separate ties for clarity
only. Create preset 3 for room 7, which ties
]
input 12 to output 7, input 11 to output 5,
input 4 to output 5, and input 6 to output 6.
X!
Input
Input 27 is tied to output 15.
Input 2 is tied to output 7.
X# ] X#
... Each
2 n
output, starting from output 1.
n is the highest-numbered installed output.
1 = muted
X1)
X* X1)
preset .
X@
is tied to output .
response is the mute status of an
s) assigned)
27