Specifications - Sanyo Denki SANUPS E11A102U-J Instruction Manual

Characteristics
§ 1 9 . 4 S
§ 1 9 . 4 S
Item
MODEL
TYPE
Output capacity
Cooling system
Input plug
Inlet
Phases
Voltage
Frequency
Power requirements
Input power factor
Outlet
Phases
Voltage
Voltage regulation
Rated frequency
Battery power startup
frequency
Frequency regulation
Voltage waveform
Distortion factor of
voltage waveform
Rapid load
change
Transient
Power outage,
voltage
recovery
variation
Rapid input
voltage change
Response time
Load power factor
(lag)
Overcurrent
protection
Inverter
Overload
capability
Bypass
Type
Number
Rated capacity
Backup time
Generated heat
Input leakage current
Operating environment
Acoustic noise
Safety standard
Emission
Immunity
(*1) The inverter is capable of operation synchronized with AC input frequency and instantaneous switchover provided that the
AC input frequency is within the rated frequency, and the AC input voltage is within the rated voltage.
(*2) When input voltage waveform distortion is under 1%.
(*3) The UPS contains batteries. Battery service life will be foreshortened if the UPS is used in an environment where the ambient
temperature exceeds 30°C (86°F).
(*4) If grounded, the ground phase of the input and output must match according to UPS specifications.
(*5) The above table lists standard specifications. Some specifications are different for units with long backup times. For details,
refer to the external battery specification instruction manual.
(*6) Voltage settable function is available for the E11A***U002J model only. Default setting is 200V. E11A***U002 model is
designed for a 208V AC power supply. This Model is authorized as UL Model.
(*7) During Double Conversion mode operation. When UPS operates in Economy mode or Active Filter mode, these depend on
utility power.
67
p e c i f i c a t i o n s
p e c i f i c a t i o n s
Standard or Performance
E11A102U
012 012J
E11A102B
012US 012UJ
1kVA/0.7kW
IEC60320-C14
Single phase, 2-wire
208V
See Notes
-20% to +15%: Double conversion mode operation
±5%: Economy or Active Filter mode operation when Auto is set.
±8%: Economy mode operation when Economy is set.
0.9kVA
IEC60320-C13 × 4
Single phase, 2-wire
208V
See Notes
Rated voltage 2%
50Hz 60Hz
Rated frequency within ±1%: Double conversion setting.
Rated frequency within ±1%, ±3% or ±5%: Auto or Economy setting.
Linear load: 3% or less
100% rectifier load: 7% or less
Auto switch to bypass circuit at 105% or more
8A
(supplementary breaker)
Small-sized valve regulated lead-acid battery
2
68W
125W
3mA or less
Ambient temperature: 0 to 40°C (32 to 104°F)
Relative humidity: 20 to 90%
40 dB or less
UL1778-4th/C22.2 No.107.3-05-2nd, CE: EN62040-1:2008
EN62040-2 C2：2006 EN62040-2 C3：2006
FCC Part15 Sub partB Class-A
EN50091-2:1995, EN55022:1994/A1:1995/A2:1997 Class-A，
EN62040-2:2006, EN55024:1998/A1:2001/A2:2003
E11A202U E11A302U
012 012J 012
E11A202B E11A302B
012US 012UJ 012US
2 kVA/1.4kW 3 kVA/2.1kW
Forced air cooling
NEMA L6-20P
IEC60320-C20
208V 208V
See Notes
50Hz or 60Hz
1.8kVA 2.7kVA
0.95 or more
IEC60320-C19 × 3
208V 208V
See Notes
50Hz or 60Hz
50Hz 60Hz 50Hz
Sine wave
Rated voltage 5 %
5 cycles or less
0.7 (lag)
105%
15A 20A
4
136W 204W
5 minutes
270W 460W
3.5mA or less
45 dB or less
012J
012UJ
200,220,230,240V: User settable
See Notes
(Rated voltage same as output voltage)
8%: Double Conversion mode
1, 3, 5%: Economy /Active Filter mode
Max. capacity during battery charging
During rated output
200,220,230,240V: User settable
See Notes
During Double Conversion mode operation
Same as input frequency (auto selection)
60Hz User settable
1, 3, 5% selectable
UPS free running operation 0.5%
During rated output
0% 100% at transient or output switch
(*7)
During rated output
10% variation
(*7)
Variation range 0.7 (lag) to 1.0
With auto return function
200ms
200% 30 sec., 800% 2 cycle (reference)
6 12V per battery, series
15 minute-rate
At 25°C (77°F) ambient temperature, rated
load
During Double Conversion mode operation
1 m (approx. 40 inches) from UPS front
panel, 'A' characteristics (linear load)
At Economy mode operation
Notes
(*7)
(*6)
(*2)
(*6)
(*3)