Brocade Communications Systems FastIron SX 800 Diagnostic Manual page 177

debug pimsm-snoop control-source
Syntax: [no] debug pimsm-snoop control-source source_address
This command displays the PIM-SM snooping related debug information for the specified control
source address. Command output resembles the following example.
Brocade# debug pimsm-snoop control-source 10.27.27.2
Brocade# PIMv2 Hello from 10.27.27.2 port 1/1/12 on vlan 275
PIMv2 Join/Prune from 10.27.27.2 port 1/1/12 on vlan 275
PIMv2 Hello from 10.27.27.2 port 1/1/12 on vlan 275
PIMv2 Hello from 10.27.27.2 port 1/1/12 on vlan 275
PIMv2 Join/Prune from 10.27.27.2 port 1/1/12 on vlan 275
PIMv2 Hello from 10.27.27.2 port 1/1/12 on vlan 275
PIMv2 Hello from 10.27.27.2 port 1/1/12 on vlan 275
debug pimsm-snoop enable
Syntax: [no] debug pimsm-snoop enable
This command enables debugging of the PIM-SM snooping activity. Command output resembles
the following example.
Brocade# debug pimsm-snoop enable
pimsm-snoop debug is enabled
debug pimsm-snoop group
Syntax: [no] debug pimsm-snoop group group_address
The group_address is the address of the PIM-SM snoop multicast group.
This command displays the PIM-SM snooping multicast group information. Command output
resembles the following example.
Brocade# debug pim-sm-snoop group 228.228.0.1
Brocade# PIM from 10.27.27.2, vlan 275, e1/1/12 has G=228.228.0.1 with 1 JOIN, 0
PRUNE
JOIN, 0 PRUNE)
PIM from 10.27.27.2, vlan 275, e1/1/12 has G=228.228.0.1 with 0 JOIN, 1 PRUNE
10.27.27.2, vlan 275, port 1/1/12: G=228.228.0.1 Src=10.0.0.1
Pim snoop, age oif (* 228.228.0.1) remove e1/1/12, pim_prune=0
debug pimsm-snoop level
Syntax: [no] debug pimsm-snoop level decimal
The decimal variable specifies the debugging level of PIM-SM snooping activity and it can take
values from 1 through 3.
This command sets the debuging level of PIM-SM snooping activity. Level 3 displays more
information than level 2, and level 0 displays no information. Command output resembles the
following example.
Brocade# debug pimsm-snoop level 1
pimsm-snoop debug level is set to 1
Brocade# PIMv2 Hello from 10.27.27.2 port 1/1/12 on vlan 275
PIMv2 Hello from 10.27.27.1 port 1/1/26 on vlan 275
Brocade FastIron, FCX, ICX, and TurboIron Diagnostic Reference
53-1002965-01
pim_snoop join (10.27.27.5 228.228.0.1), from e1/1/12
PIM from 10.27.27.2, vlan 275, port 1/1/12: G=228.228.0.1 Src=10.0.0.1
pim_snoop prune 1/1/12 from (10.27.27.5, 228.228.0.1),
PIM-SM snooping debug commands
6
(1
PIM from
(0 JOIN, 2 PRUNE)
165