Brocade Communications Systems FastIron SX 800 Diagnostic Manual page 172

6
PIM debug commands
send_J/P_msg(), lcl_adr=10.10.119 dest=224.0.0.13 pkt_size=126 to v100
group address: 225.1.1.6
send_J/P_msg(), lcl_adr=10.10.119 dest=224.0.0.13 pkt_size=154 to v100
group address: 225.1.1.5
send_J/P_msg(), lcl_adr=10.10.119 dest=224.0.0.13 pkt_size=182 to v100
group address: 225.1.1.4
send_J/P_msg(), lcl_adr=10.10.119 dest=224.0.0.13 pkt_size=210 to v100
group address: 226.1.1.1
send_J/P_msg(), lcl_adr=10.10.119 dest=224.0.0.13 pkt_size=238 to v100
group address: 225.1.1.3
send_J/P_msg(), lcl_adr=10.10.119 dest=224.0.0.13 pkt_size=266 to v100
group address: 225.1.1.2
send_J/P_msg(), lcl_adr=10.10.119 dest=224.0.0.13 pkt_size=294 to v100
group address: 225.1.1.1
send_J/P_msg(), lcl_adr=10.10.119 dest=224.0.0.13 pkt_size=322 to v100
group address: 226.1.1.2
send_J/P_msg(), lcl_adr=10.10.119 dest=224.0.0.13 pkt_size=350 to v100
group address: 227.1.1.2
send_J/P_msg(), lcl_adr=10.10.119 dest=224.0.0.13 pkt_size=378 to v100
group address: 227.1.1.1
send_J/P_msg(), lcl_adr=10.10.119 dest=224.0.0.13 pkt_size=406 to v100
00:22:16 Send PIM_V2 Join/Prune Src 10.10.119 Dst 224.0.0.13 Len 406 on v100
PIMSM: END Periodic join-prune msgs
debug ip pim nbr-change
Syntax: [no] debug ip pim nbr-change nbr_address
The nbr_address variable specifies the IP address of the neighbor.
This command controls the PIM IPv4 neighbor changes and the command output resembles the
following example.
Brocade# debug ip pim nbr-change 10.144.144.12
PIM:
Brocade(config-if-e1000-1/1/11)# PIM-NBR.VRF0: Neighbor 10.144.144.12 on
interface tn4, 1/1/11 deleted on port-down
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.11) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.12) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.13) HW bits: 0 0
160
Join list: (10.10.129 225.1.1.6) wc=1 rpt=1 sparse=1
Join list: (10.11.10.101 225.1.1.6) wc=0 rpt=0 sparse=1
Join list: (10.10.129 225.1.1.5) wc=1 rpt=1 sparse=1
Join list: (10.11.10.101 225.1.1.5) wc=0 rpt=0 sparse=1
Join list: (10.10.129 225.1.1.4) wc=1 rpt=1 sparse=1
Join list: (10.11.10.101 225.1.1.4) wc=0 rpt=0 sparse=1
Join list: (10.10.129 226.1.1.1) wc=1 rpt=1 sparse=1
Join list: (10.11.10.101 226.1.1.1) wc=0 rpt=0 sparse=1
Join list: (10.10.129 225.1.1.3) wc=1 rpt=1 sparse=1
Join list: (10.11.10.101 225.1.1.3) wc=0 rpt=0 sparse=1
Join list: (10.10.129 225.1.1.2) wc=1 rpt=1 sparse=1
Join list: (10.11.10.101 225.1.1.2) wc=0 rpt=0 sparse=1
Join list: (10.10.129 225.1.1.1) wc=1 rpt=1 sparse=1
Join list: (10.11.10.101 225.1.1.1) wc=0 rpt=0 sparse=1
Join list: (10.10.129 226.1.1.2) wc=1 rpt=1 sparse=1
Join list: (10.11.10.101 226.1.1.2) wc=0 rpt=0 sparse=1
Join list: (10.10.129 227.1.1.2) wc=1 rpt=1 sparse=1
Join list: (10.11.99.99 227.1.1.2) wc=0 rpt=0 sparse=1
Join list: (10.10.129 227.1.1.1) wc=1 rpt=1 sparse=1
Join list: (10.11.99.99 227.1.1.1) wc=0 rpt=0 sparse=1
nbr-change debugging is on
Brocade FastIron, FCX, ICX, and TurboIron Diagnostic Reference
53-1002965-01