Brocade Communications Systems FastIron SX 800 Diagnostic Manual page 132

5
IPv6 PIM debug commands
Group=ff0::5. Prune list: 0 srcs
Group=ff0::6. Join list: 1 srcs
fe80::768e:f8ff:fe3e:9600, intf v1844,1/1/11
debug ipv6 pim nbr-change
Syntax: [no] debug ipv6 pim nbr-change [nbr_address]
The nbr_address variable specifies the neighbor address.
This command controls the IPv6 PIM neighbor changes and the command output resembles the
following example.
Brocade# debug ipv6 pim nbr-change
PIM6:
Brocade# PIM.VRF0: Rx Hello msg from fe80::768e:f8ff:fe3e:9600 on intf v1844,
1/1/11-1/1/14
Brocade(config-if-e1000-1/1/11)# disable
Brocade(config-if-e1000-1/1/11)# PIM-NBR.VRF0: Neighbor fe80::768e:f8ff:fe3e:9600
on interface v1844, 1/1/11 deleted on port-down
PIM.VRF0: Rx Hello msg from fe80::768e:f8ff:fe46:5580 on intf v170, 6/1/17
PIM.VRF0: Rx Hello msg from fe80::768e:f8ff:fe46:5580 on intf v170, 6/1/17
Brocade(config-if-e1000-1/1/11)# enable
Brocade(config-if-e1000-1/1/11)# PIM.VRF0: Rx Hello msg from
fe80::768e:f8ff:fe46:5580 on intf v170, 6/1/17
PIM.VRF0: Rx Hello msg from fe80::768e:f8ff:fe46:5580 on intf v170, 6/1/17
PIMV2 rcvd from fe80::768e:f8ff:fe3e:9600 on v1844 (phy e1/1/11), not pim
neighbour
PIM.VRF0: Rx Hello msg from fe80::768e:f8ff:fe3e:9600 on intf v1844, 1/1/11-1/1/14
PIM-NBR.VRF0: Neighbor fe80::768e:f8ff:fe3e:9600 on interface v1844, 1/1/11 genid
changed from 4294953471 to 13824
PIM-NBR.VRF0: GenId changed for Neighbor fe80::768e:f8ff:fe3e:9600 on interface
v1844, 1/1/11 ; new GenId 13824
PIM-NBR.VRF0: Neighbor fe80::768e:f8ff:fe3e:9600 on interface v1844, 1/1/11 added
PIM.VRF0: Rx Hello msg from fe80::768e:f8ff:fe46:5580 on intf v170, 6/1/17
PIM.VRF0: Rx Hello msg from fe80::768e:f8ff:fe46:5580 on intf v170, 6/1/17
PIM.VRF0: Rx Hello msg from fe80::768e:f8ff:fe3e:9600 on intf v1844, 1/1/11-1/1/14
debug ipv6 pim packet
Syntax: [no] debug ipv6 pim packet source_address group_address [rate]
•
•
•
This command displays debugging information about the IPv6 PIM packets. Command output
resembles the following example.
Brocade# debug ipv6 pim packet
Rx Pkt (2001:DB8::200, ff0::18) on v1244(1/11).
Rx flow on intf/port diff than entry's intf v1244 or port INVALID
send MCAST_FIRST_DATA: entry phy port: INVALID, pkt input port: 1/11-1/14.
SPT-F, FAST-F
* *: 0 pkt,from v1244(e1/11), dup. pkt to v55 phy e1/1, l2=0
SW forwarded pkt to 1 oif(s)
120
J-Src=2001:DB8::200, wc=0, rpt=0, SM=1
PIM.VRF0: Processing (S,G) Join (2001:DB8::200 ff84::6) from
nbr-change debugging is on
source_address - Specifies the IPv6 source address of the PIM packet
group_address - Specifies the IPv6 group address of the PIM packet.
rate - Specifies the hardware rate.
Brocade FastIron, FCX, ICX, and TurboIron Diagnostic Reference
53-1002965-01