Ordering - GE L30 Instruction Manual

2.1 INTRODUCTION
Table Notes:
1. RW = read and write access
2. R = read access
3. Supervisor = RW (default), Administrator = R (default), Administrator = RW (only if Supervisor role is disabled)
4. NA = the permission is not enforced by CyberSentry Security
2
CYBERSENTRY SERVER AUTHENTICATION
The UR has been designed to automatically direct authentication requests based on user names. In this respect, local
account names on the UR are considered as reserved, and not used on a RADIUS server.
The UR automatically detects whether an authentication request is to be handled remotely or locally. As there are only five
local accounts possible on the UR, if the user ID credential does not match one of the five local accounts, the UR automat-
ically forwards the request to a RADIUS server when one is provided.
If a RADIUS server is provided, but is unreachable over the network, server authentication requests are denied. In this situ-
ation, use local UR accounts to gain access to the UR system.
a) OVERVIEW
The L30 is available as a 19-inch rack horizontal mount or reduced-size (¾) vertical unit and consists of the following mod-
ules: power supply, CPU, CT/VT, contact input and output, transducer input and output, and inter-relay communications.
Each of these modules can be supplied in a number of configurations specified at the time of ordering. The information
required to completely specify the relay is provided in the following tables (see chapter 3 for full details of relay modules).
Order codes are subject to change without notice. See the ordering page at
http://www.gedigitalenergy.com/multilin/order.htm
NOTE
The order code structure is dependent on the mounting option (horizontal or vertical) and the type of CT/VT modules
(enhanced diagnostic CT/VT modules or HardFiber
following sub-sections.
b) ORDER CODES WITH ENHANCED CT/VT MODULES
The order codes for the horizontal mount units are shown below.
Table 2–4: L30 ORDER CODES (HORIZONTAL UNITS)
L30 - * ** - *
BASE UNIT L30 | |
CPU T |
U |
V |
SOFTWARE 00
03
06
07
18
19
24
25
26
27
A0
A3
A4
A6
A7
AI
AJ
AO
AP
AQ
AR
B0
B3
B4
B6
B7
BI
BJ
BO
BP
BQ
BR
C0
C3
C6
C7
CI
CJ
CO
CP
CQ
CR
2-8
TM
* * - F ** - H ** - L ** - N **
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
L30 Line Current Differential System
for the latest options.
process bus modules). The order code options are described in the
- S ** - U ** - W/X ** Full Size Horizontal Mount
| | | | Base Unit
| | | | RS485 and Three Multi-mode fiber 100Base-FX (SFP with LC)
| | | | RS485 and Two Multi-mode fiber 100Base-FX (SFP with LC), One 10/100Base-T (SFP with RJ45)
| | | | RS485 and Three 10/100Base-T (SFP with RJ45)
| | | | No software options
| | | | IEC 61850
| | | | One phasor measurement unit (PMU)
| | | | IEC 61850 and one phasor measurement unit (PMU)
| | | | Synchrocheck and three-pole autoreclose
| | | | Synchrocheck, three-pole autoreclose, and one phasor measurement unit (PMU)
| | | | In-zone transformer protection
| | | | In-zone transformer protection and IEC 61850
| | | | In-zone transformer protection and one phasor measurement unit (PMU)
| | | | In-zone transformer protection, IEC 61850, and one phasor measurement unit (PMU)
| | | | CyberSentry Lvl 1
| | | | CyberSentry Lvl 1 and IEC 61850
| | | | CyberSentry Lvl 1 and IEC 61850 and Ethernet Global Data (EGD)
| | | | CyberSentry Lvl 1 and phasor measurement unit (PMU)
| | | | CyberSentry Lvl 1 and IEC 61850 and phasor measurement unit (PMU)
| | | | CyberSentry Lvl 1 and three-pole autoreclose and synchrocheck
| | | | CyberSentry Lvl 1 and three-pole autoreclose and synchrocheck and one PMU
| | | | CyberSentry Lvl 1 and In-zone transformer protection
| | | | CyberSentry Lvl 1 and IEC 61850 and In-zone transformer protection
| | | | CyberSentry Lvl 1 and phasor measurement unit (PMU) and In-zone transformer protection
| | | | CyberSentry Lvl 1 and IEC 61850 and (PMU) and In-zone transformer protection
| | | | IEEE 1588
| | | | IEEE 1588 and IEC 61850
| | | | IEEE 1588 and IEC 61850 and Ethernet Global Data (EGD)
| | | | IEEE 1588 and phasor measurement unit (PMU)
| | | | IEEE 1588 and IEC 61850 and phasor measurement unit (PMU)
| | | | IEEE 1588 and three-pole autoreclose and synchrocheck
| | | | IEEE 1588 and three-pole autoreclose and synchrocheck and one PMU
| | | | IEEE 1588 and In-zone transformer protection
| | | | IEEE 1588 and IEC 61850 and In-zone transformer protection
| | | | IEEE 1588 and phasor measurement unit (PMU) and In-zone transformer protection
| | | | IEEE 1588 and IEC 61850 and (PMU) and In-zone transformer protection
| | | | Parallel Redundancy Protocol (PRP)
| | | | PRP and IEC 61850
| | | | PRP and PMU
| | | | PRP, IEC 61850, and PMU
| | | | PRP, three-pole autoreclose, and synchrocheck
| | | | PRP, three-pole autoreclose, PMU, and synchrocheck
| | | | PRP and in-zone transformer protection
| | | | PRP, in-zone transformer protection, and IEC 61850
| | | | PRP, in-zone transformer protection, and PMU
| | | | PRP, in-zone transformer protection, IEC 61850, and PMU
2 PRODUCT DESCRIPTION

2.1.4 ORDERING

GE Multilin