Rfc 2833 Ans Report Upon Fax/Modem Detection; Fax Support - AudioCodes Mediant 800B User Manual
Analog & digital voip media gateway
Hide thumbs
Also See for Mediant 800B:
- User manual (1338 pages) ,
- Installation and maintenance manual (104 pages) ,
- Hardware installation manual (56 pages)
Table of Contents
Advertisement
c.
Set the 'V.22 Modem Transport Type' parameter to Disable
(V22ModemTransportType = 0).
d.
Set the 'V.23 Modem Transport Type' parameter to Disable
(V23ModemTransportType = 0).
e.
Set the 'V.32 Modem Transport Type' parameter to Disable
(V32ModemTransportType = 0).
f.
Set the 'V.34 Modem Transport Type' parameter to Disable
(V34ModemTransportType = 0).
3.
Set the ini file parameter, BellModemTransportType to 0 (transparent mode).
4.
Configure the following optional parameters:
a.
Coders table - (Configuration tab > VoIP menu > Coders and Profiles >
Coders).
b.
'Dynamic Jitter Buffer Optimization Factor' (DJBufOptFactor) - RTP/RTCP
Settings page (Configuration tab > VoIP menu > Media > RTP/RTCP Settings).
c.
'Silence Suppression' (EnableSilenceCompression) - Voice Settings page
(Configuration tab > VoIP menu > Media > Voice Settings).
d.
'Echo Canceller' (EnableEchoCanceller) - Voice Settings page.
Note:
This mode can be used for fax, but is not recommended for modem
transmission. Instead, use the Bypass (see ''Fax/Modem Bypass Mode'' on page 173)
or Transparent with Events modes (see ''Fax / Modem Transparent with Events
Mode'' on page 175) for modem.
14.2.2.8 RFC 2833 ANS Report upon Fax/Modem Detection
The device (terminator gateway) sends RFC 2833 ANS/ANSam events upon detection of
fax and/or modem answer tones (i.e., CED tone). This causes the originator to switch to
fax/modem. This parameter is applicable only when the fax or modem transport type is set
to bypass, Transparent-with-Events, V.152 VBD, or G.711 transport. When the device is
located on the originator side, it ignores these RFC 2833 events
To configure RFC 2833 ANS Report upon fax/modem detection:
1.
In the SIP General Parameters page (Configuration tab > VoIP menu > SIP
Definitions > General Parameters), set the 'Fax Signaling Method' parameter to No
Fax or Fax Fallback (IsFaxUsed = 0 or 3).
2.
In the Fax/Modem/CID Settings page, do the following:
a.
Set the 'Fax Transport Mode' parameter to Bypass (FaxTransportMode = 2).
b.
Set the 'V.xx Modem Transport Type' parameters to Enable Bypass
(VxxModemTransportType = 2).
3.
Set the ini file parameter, FaxModemNTEMode to 1 (enables this feature).
14.2.3 V.34 Fax Support
V.34 fax machines can transmit data over IP to the remote side using various methods.
The device supports the following modes for transporting V.34 fax data over IP:
T38 Version 3 - V.34 fax relay mode
Bypass mechanism for V.34 fax transmission (see ''Bypass Mechanism for V.34 Fax
Transmission'' on page 177)
T38 Version 0 relay mode, i.e., fallback to T.38 (see ''Relay Mode for T.30 and V.34
Faxes'' on page 178)
User's Manual
Mediant 800B Gateway and E-SBC
176
Document #: LTRT-10620
Advertisement
Table of Contents
