Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 HID Headlamps Usage and Safety Pre‐ cautions Never Change a Headlamp Bulb If You Are Not Familiar with the Corresponding Steps, Safety Precautions and the Tool. WARNING Life-threatening danger due to high voltage.
Page 11
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Caution ♦ Do not touch HID headlamp bulb glass cones with bare hands. The remaining fingerprint would evaporate due to the heat of the operated bulb and condense on the reflec‐...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Battery ⇒ “3.1 Battery, General Information”, page 5 ⇒ “3.2 Battery Types”, page 5 Battery, General Information All instructions and information on this chapter. Refer to ⇒ Elec‐...
Page 16
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Open the cover -4- over the battery negative terminal. – Loosen the nut -6- a few turns and disconnect the battery ground cable terminal clamp -5- from the battery negative ter‐...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Insert the Battery - A- into the battery tray -1- so that the battery base strip touches the rear and side stop -arrows-. • It must not be possible to slide the Battery - A- rearward or to the side.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Loosen the nut -3- several turns and remove the battery ground cable terminal clamp -2- from the battery terminal. Connecting Pay attention to the following when disconnecting the Battery - A- .
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Free up the wiring harness from the battery tray -arrows-. – Remove the bolts and nut -2-. – Remove the battery tray -1-. Installing Install in reverse order of removal.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Release and disconnect the connector -2- from the Battery Monitoring Control Module - J367- -3-. – Remove the nut -1- for the ground cable -2-. – Remove the nut -3- and remove the ground cable with Battery Monitoring Control Module - J367- -4-.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Generator, Removing and Installing ⇒ “2.2.2 Generator, Removing and Installing, Vehicles with 2.0L TSI Engine”, page 16 ⇒ “2.2.3 Generator, Removing and Installing, Vehicles with 1.8L TSI-Engine”, page 18 ⇒...
Page 24
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the Generator - C- -1- downward and to the right. Installing Install in the reverse order of removal while paying attention to the following: – Move the bolt sleeves slightly to the rear to make it easier to install the Generator - C- .
Page 25
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Detach the hose clamps -1 and 2- and remove the air hose. – Seal the open lines and connections with clean plugs from the -VAS6122- .
Page 26
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Free up the wiring harness -arrow-. – Remove the bolts -5 and 6- and bring the Generator - C- -4- forward. – Disconnect the connector -3-.
Page 27
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the bolts -arrows-. – Move aside the coolant pipe -1-. – Remove the bolts -1 and 2-. – Pivot the Generator - C- -3- in the direction of travel.
Page 28
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Vehicles with A/C system Caution Danger of damaging the A/C compressor, the refrigerant line and hoses. ♦ Do not stretch, bend or kink the refrigerant lines and ho‐...
Page 29
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Removing – Disconnect the Battery - A- . Refer to ⇒ “1.3 Battery, Disconnecting and Connecting”, page 9 – Remove the ribbed belt. Refer to ⇒ Rep. Gr. 13 ; Cylinder Block, Belt Pulley Side;...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Generator, Checking – Check the Generator - C- using the Vehicle Diagnostic Tester . Ribbed Belt Pulley, Removing and In‐ stalling ⇒ “2.4.1 Ribbed Belt Pulley without Freewheel, Removing and Installing”, page 22...
Page 31
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Pry up the cap from the ribbed belt pulley. – Install the -3400- with the wrench (SW 17) in the ribbed belt pulley. – Install the multi-point socket M10 -1- in the generator shaft.
Page 32
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 2.4.3 Ribbed Belt Pulley with Freewheel, Re‐ moving and Installing, Valeo Special tools and workshop equipment required ♦ Multi-Tooth Adapter - 3400- ♦ Torque Wrench 1332 40-200Nm - VAG1332- ♦...
Page 33
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Install the -VAG1603A/1- in the generator shaft. – Counterhold the -3400- with a wrench (SW 17). – Tighten the ribbed belt pulley by turning the generator shaft to the left using -VAG1332- .
Page 34
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 -B- large decoupling belt pulley with freewheel, special tool to be used -3400- Note The ribbed belt for the large decoupling belt pulley with freewheel must be longer, because the decoupling belt pulley with freewheel has a larger diameter and it is different for vehicles with and with‐...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Insert the -T10474- or the -3400- -1- into the decoupling belt pulley with freewheel and attach a wrench. – Install the -VAG1603A/1- -2- in the generator shaft.
Page 36
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the Voltage Regulator - C1- from the Generator - C- . Installing Install in the reverse order of removal while paying attention to the following:...
Page 37
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Press the cap on the carbon brushes -A- down in direction of -arrow- until it is flush with the voltage regulator housing. – Install new cap -1- on the Generator - C- .
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 3.1.4 Overview - Starter, Vehicles with Automatic Transmission 1 - Starter - B- ❑ Removing and instal‐ ling. Refer to ⇒ “3.2.4 Starter, Re‐ moving and Installing, Vehicles with Automatic Transmission”,...
Page 42
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Removing – Disconnect the Battery - A- . Refer to ⇒ “1.3 Battery, Disconnecting and Connecting”, page 9 – Remove the noise insulation. Refer to ⇒ Body Exterior; Rep.
Page 43
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the Starter - B- -3- downward. Installing Install in the reverse order of removal while paying attention to the following: – Connect the Battery - A- . Refer to ⇒...
Page 44
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the Starter - B- -3- upward. Installing Install in the reverse order of removal while paying attention to the following: – Connect the Battery - A- . Refer to ⇒...
Page 45
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the Starter - B- -2- upward. Installing Install in the reverse order of removal while paying attention to the following: – Connect the Battery - A- . Refer to ⇒...
Page 46
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Slide the cap -1- in the direction of the arrow in direction of -A-. – Release and disconnect the connector -1-. – Remove the nut -3- and remove terminal 30/B+ -2-.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Cruise Control System All instructions and information on this chapter. Refer to ⇒ Elec‐ trical Equipment General Information; Rep. Gr. 27 ; Cruise Con‐ trol System .
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Start/Stop System ⇒ “5.1 General Description for Start/Stop System”, page 40 ⇒ “5.2 Component Location Overview - Start/Stop System”, page General Description for Start/Stop Sys‐ The Start/Stop System reduces fuel consumption by turning off the engine when the vehicle is at a standstill and turning the en‐...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 10 - Adaptive Cruise Control Button - E357- ❑ Is integrated in the multifunction steering wheel. ❑ Removing and installing. Refer to ⇒ Communication; Rep. Gr. 91 ; Multifunction Steering Wheel; Right and Left Multifunction Buttons on Steering Wheel - E441- / - E440- , Removing and Installing .
Page 51
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Release and disconnect the connector -2-. Installing Install in the reverse order of removal while paying attention to the following: – Calibrate the adaptive cruise control. Refer to ⇒...
Page 52
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Adjusting Screws, Adjusting – Using the -VAS6335- measure the adjustment dimension -a- on all adjusting screws and adjust where necessary. ♦ Dimension -a- = 40.3 mm ± 0.5 mm –...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Loosen the catches -1- on both sides in the direction of the -arrow A-. – Remove the rain sensor trim -2-. – Loosen the locking mechanisms -1- in the direction of the -arrow A-.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 1 - Front Passenger Side Wip‐ er Blade ❑ Different lengths. Refer to the Parts Catalog. ❑ Removing and instal‐ ling. Refer to ⇒ “1.3 Wiper Blade, Re‐...
Page 63
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Tightening Specifications and Sequence for the Windshield Wiper Motor - V- – Tighten the bolts in steps according to the sequence shown: Step Bolts Tightening Specification -1 to 3-...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Wiper, Moving Into Service Position Caution Risk of damaging the hood by putting the wipers back in basic setting. ♦ Do not drive a vehicle with windshield wiper arms folded ♦...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Press the clip in direction of -arrow A- and remove the wiper blade -1- from the windshield wiper arm -2- in direction of -arrow B-. – Remove the wiper blade -1-.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Pry the caps -3- off of the windshield wiper arms -1- with a screwdriver. – Loosen the nuts -2- several turns. – Position the -T10369/1- on the wiper arm -1- as illustrated.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Align the wiper blade as follows on the windshield. The dimensions give the distance of the wiper blade tips to the plenum chamber cover on the lower edge of the windshield.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – When necessary disconnect the damping regulation connec‐ tor. – Remove the wiper frame -2- with linkage and the Windshield Wiper Motor - V- from the plenum chamber.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Pry the operating rod -4- on the ball joint from the motor crank -2- using the -80-200- . – Remove the nut -1-. – Remove the motor crank -2- from the windshield wiper motor shaft.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 function was deactivated as well as new Windshield Wiper Motor - V- . – Deactivate the wiper motor alternating park position using the Vehicle Diagnostic Tester .
Page 71
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Release the left and right wire retainer -arrows-. – Pry the Rain/Light Recognition Sensor - G397- -1- starting at the top carefully from the frame on the windshield.
Page 72
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Install the Rain/Light Recognition Sensor - G397- -1- in the frame on the windshield. – Engage the wire retainer audibly on both sides -arrow-. Even if the sensor is installed correctly, small air bubbles can form between the windshield and the connecting pad.
Page 73
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Release the connection -1- and remove and remove the Rain/ Light Recognition Sensor - G397- -2-. Caution Lay the removed Rain/Light Recognition Sensor - G397- until it is reinstalled so that the connecting pad is not contaminated with dust or other deposits.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – If the Rain/Light Recognition Sensor - G397- was replaced it must be adapted using the Vehicle Diagnostic Tester . 1.10 Rain/Light Recognition Sensor, Servic‐ ⇒ “1.10.1 Rain/Light Recognition Sensor, Servicing, TRW”, page ⇒...
Page 75
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Release the tab -arrows- on both sides and separate the hous‐ ing upper section -1- with optical unit from the housing lower section -2-. Caution The sensor electronics may be damaged.
Page 76
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Place the sensor film -2- using the clear protective film -1- on the Rain/Light Recognition Sensor - G397- -3-. – Press the sensor film through the protective film -1- free of bubbles on the Rain/Light Recognition Sensor - G397- -2-.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 ❑ For the washer fluid reservoir 10 - Filler Tube Caution Risk of leaks! Cannot be separated from the filler tube. ❑ For the washer fluid reservoir...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Retainer the retaining tabs -3-. Caution There is a danger of leaks. ♦ The windshield washer fluid reservoir is one part. Sepa‐ rating between the washer fluid reservoir, filler tube and filler neck is not possible.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Removing – Open the hood. – Push the spray nozzle upward -arrow A- and tilt it out from under the flap -arrow B-. – Release the hose clip -1- in the direction of -arrow- and remove the hose connection -2- from the spray nozzle -4-.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 8 - Spacer ❑ Quantity: 3 Wiper Blade, Removing and Installing Caution Risk of damaging the wiper blade. ♦ Joint-free windshield wipers are very flexible. Only take hold of the wiper blades in the wiper blade mounting area in order to lift them away from the rear window.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Completely remove the nut -4- and remove the windshield wiper arm. Installing Install in the reverse order of removal while paying attention to the following: – Adjust the wiper arm. Refer to ⇒...
Page 87
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the lower rear lid trim panel. Refer to ⇒ Body Interior; Rep. Gr. 70 ; Luggage Compartment Trim Panels; Rear Lid Lower Trim Panel, Removing and Installing .
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Spray Nozzles, Adjusting The nozzles are already adjusted by the manufacturer and must not be adjusted after installation. – Check the adjustment of the spray nozzle. Refer to ⇒ Mainte‐...
Page 96
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the lift cylinder -2- downward from the bracket -3-. Installing Install in the reverse order of removal while paying attention to the following: Pay attention to the markings on the lift cylinder for the left and right.
Page 110
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Note If only one headlamp was removed, then the front bumper ♦ cover must be loosened only on the respective side. If both headlamps are removed, then the front bumper must ♦...
Page 111
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the bolts between the bumper cover and lock carrier from below. – If equipped, remove the bolts -1-. – Detach the bumper cover -2- from the fender and remove in the direction of the -arrow A-.
Page 112
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Tape off the marked areas -3- on the headlamp -2-. – Tape off the bottom of the fender brace -4-. – Tape off the marked area -5- on the bumper cover -1-.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Slide the headlamp into the bumper cover guide. – Uniformly adjust the headlamp gap distribution. Refer to ⇒ “1.4 Headlamp Installation Position, Correcting”, page 105 – Push on the bumper cover -1-. Pay attention that it is pushed in the mounts -2- under the headlamp.
Page 114
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Uniformly adjust the gap distribution of the headlamp -1- to the fender. – Tighten the bolts -5 and 6-. – Close the hood. – Uniformly adjust the gap distribution of the banjo bolt for the bolt -3- and the impact screw -2-.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Tightening Specifications Left/Right Front Turn Signal Bulb -M5- / -M7- , Removing and Installing ⇒ “1.5.1 Left/Right Front Turn Signal Bulb M5 / M7 , Removing and Installing, Halogen Dual Headlamp”, page 107 ⇒...
Page 116
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the Left Front Turn Signal Bulb - M5- -2- from the socket -1-. Installing Install in the reverse order of removal while paying attention to...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Turn the bulb socket -1- counter-clockwise until stop. – Remove the bulb socket -1- in the direction of -arrow A- out of the reflector -2-. – Release and disconnect the connector -1- on the Left Front Turn Signal Bulb - M5- with the bulb socket -2-.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Install the headlamp and align to the body contour. – Perform a function test. – Check and correct headlamp adjustment, if necessary. Refer to ⇒ Maintenance ; Booklet 36.1 ; Procedure Descriptions .
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 1.7.2 Headlamp, Changing from LHD to RHD, Except Halogen Dual Headlamp If the vehicle is driven in countries where the traffic drives on the other side of the road (either right-hand or left-hand traffic) than where it is normally driven, both headlamps must be adjusted.
Page 120
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Pull the Left Headlamp Beam Adjustment Motor - V48- -1- in the direction of the -arrow C-. – Turn the height adjustment -2- in the direction of the -arrow B- (lower the reflector).
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the housing cover -1- bolts -2-. – Remove the housing cover -1-. – Release the Left Headlamp Beam Adjustment Motor - V48- -1-: ♦ Turn the headlamp left in the direction of the -arrow A-.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the ignition key, if equipped. – Turn the housing cover -1- in the direction of the -arrow A-. – Remove the housing cover -1-. – Turn the bulb socket -1- in the direction of the -arrow A-, until the retaining tab -3- is in the opening -2-.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Removing – Turn off the ignition and all electrical equipment. – Remove the ignition key, if equipped. – Remove the housing cover -1- in the direction of the -arrow A-.
Page 124
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 WARNING High voltage poses a life-endangering risk, injury risk and en‐ vironmental hazard. ♦ Pay attention to usage and safety information for HID headlamps. Refer to ⇒ “1.3 HID Headlamps Usage and Safety Precautions”,...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Turn the locking mechanism -1- in the direction of the -arrow A-. – Remove the HID headlamp bulb -2- in the direction of the -arrow B- from the housing.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 1.12.2 Left/Right Position Lamp Bulb - M1- / - M3- , Removing and Installing, HID Headlamp The Left Position Lamp Bulb - M1- and the Right Position Lamp Bulb - M3- is integrated in the Left Daytime Running Lamp Bulb - L174- and in the Right Daytime Running Lamp Bulb - L175- .
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the Left Daytime Running Lamp Bulb - L174- from the handle. Installing Install in the reverse order of removal while paying attention to the following: Caution There is a risk of damaging the headlamp.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Turn the housing cover -1- in the direction of the -arrow A- and remove from the headlamp. – Push upward in the direction of the -arrow A- on the bulb sock‐...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Press the release button -4-. – Disconnect the connector -3-. Installing Install in the reverse order of removal while paying attention to the following: Caution Make sure the seal fits correctly when installing the HID head‐...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the control module. Installing Install in the reverse order of removal while paying attention to the following: Caution Make sure the seal fits correctly when installing the HID head‐...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 1.23 Left/Right Adaptive Cornering Lamp Motor - V318- / -V319- , Removing and Installing The Left Adaptive Cornering Lamp Motor - V318- / Right Adaptive Cornering Lamp Motor - V319- is installed only with HID head‐...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the screws -1-. – Pivot the fog lamp -2- in the direction of the -arrow A-. – Remove the fog lamp -2- in the direction of the -arrow B- from the bumper cover.
Page 136
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Turn the steering to the right. – Pry the cover -1- in the wheel housing liner in the direction of the -arrow A-. – Disconnect the connector -4-.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 12 - Adjusting Unit ❑ Removing and installing. Refer to ⇒ Body Exterior; Rep. Gr. 66 ; Exterior Rearview Mirror; Mirror Ad‐ justing Unit, Removing and Installing .
Page 139
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Removing – Turn off the ignition and all electrical equipment. – Remove the ignition key, if equipped. – Remove the mirror trim. Refer to ⇒ Body Exterior; Rep. Gr.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Exterior Rearview Mirror Entry Lamp, Removing and Installing Special tools and workshop equipment required ♦ Torque Wrench 1783 - 2-10Nm - VAG1783- The removal and installation is described for the left side. Re‐...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Rear Lid Tail Lamp, Removing and In‐ stalling ⇒ “4.3.1 Rear Lid Tail Lamp, Removing and Installing, Sedan”, page 140 ⇒ “4.3.2 Rear Lid Tail Lamp, Removing and Installing, Wagon”, page 141 4.3.1...
Page 149
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the Left Tail Lamp 2 - MX5- -3- outward. Installing Install in the reverse order of removal while paying attention to the following: Make sure seal between body and tail lamp housing seals prop‐...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the Left Tail Lamp 2 - MX5- -3- outward. Installing Install in the reverse order of removal while paying attention to the following: Note Make sure seal between body and tail lamp housing seals ♦...
Page 151
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Loosen the fastening element -1- two turns. – Insert a suitable screwdriver in the trim openings -2-. The tail lamp -3- must be flush with the neighboring components.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 4.5.2 Tail Lamp, Removing and Installing, Wagon The removal and installation is described for the left side. Re‐ moving and installing on the right side is identical.
Page 154
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Pry up the cover -1- in the direction of -arrow-. – Release and disconnect the connector -2-. – Push the locking mechanisms -3- in the direction of the -arrows A, B, and C-.
Page 155
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Caution Risk of damaging the component surfaces. ♦ When positioning a prying tool, put for example commer‐ cially available adhesive tape over the component in the visible area.
Page 157
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the rear fog lamp bulb -2- from the bulb holder -1-. Installing Install in the reverse order of removal while paying attention to the following: Caution There is a risk of damaging the lamp.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Disconnect the connector -2-. – Push the locking mechanisms -1- in the direction of the -arrows A and B-. – Remove the bulb holder -3- from the tail lamp.
Page 159
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Pull the bulb socket -1- straight in the direction of the -arrow A- out of the housing. – Remove the brake/tail lamp bulb from the bulb socket.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the brake and tail lamp bulb -1- in the direction of the -arrow A- from the bulb holder. Installing Install in the reverse order of removal while paying attention to...
Page 161
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Turn the bulb socket -1- in the direction of the -arrow A-. – Remove the bulb socket in the direction of the -arrow B- from the tail lamp.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Turn the bulb socket -1- in the direction of the -arrow A-. – Remove the bulb socket in the direction of the -arrow B- from the tail lamp.
Page 163
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Push the mounting tabs -2, 3 and 4- in the direction of the - arrows A-. – Remove the cover -1- from the tail lamp. Caution Do not turn the bulb socket.
Page 164
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Push the mounting tabs -1- in the direction of the -arrows A, B, and C-. – Remove the bulb holder -2-. – Remove the rear turn signal bulb -1- in the direction of the -arrow A- from the bulb holder.
Page 167
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Caution Risk of damaging the component surfaces. ♦ When positioning a prying tool, put commercially available adhesive tape over the component in the visible area. – Cover the area of the rear lid above the brake light with a strip of adhesive tape -1-.
Page 168
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the ignition key, if equipped. – Remove the spoiler on the edge of the roof. Refer to ⇒ Body Exterior; Rep. Gr. 66 ; Roof Bars/Roof Rails .
Page 170
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Removing – Turn off the ignition and all electrical equipment. – Remove the ignition key, if equipped. – Press the Left License Plate Lamp - X4- in the direction of the -arrow A- using a suitable tool.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Disconnect the connector -2-. Installing Install in the reverse order of removal while paying attention to the following: Insert the Left License Plate Lamp - X4- into the rear lid so that the connector is facing toward the right side of the vehicle.
Page 172
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Turn the lamp socket -1- in the direction of -arrow- to release it and pull it out of the license plate lamp. Installing Installation is performed in the reverse order of removal, noting...
Page 173
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the glass base bulb -1- from the bulb socket. Installing Install in reverse order of removal. Note the following: Caution There is a risk of damaging the lamp.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 7.2.3 Component Location Overview - Rear Keyless Access Authorization Sys‐ tem, Wagon 1 - Access/Start System An‐ tenna in Rear Bumper - R136- ❑ Removing and instal‐...
Page 179
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the footwell cover on the driver side. Refer to ⇒ Body Interior; Rep. Gr. 68 ; Storage Compartments and Covers; Driver Side Footwell Cover, Removing and Installing .
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 integrated in the exterior door handle and cannot be replaced in‐ dividually if faulty. – Door handle removing and installing. Refer to ⇒ Body Exterior; Rep. Gr. 57 ; Door Components; Door Handle, Removing and Installing .
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Pry out the antenna -1- with the -80-200- in the direction of the -arrow A- from the body. – Disconnect the connector -2-. Installing Install in reverse order of removal.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Push in -T40011- or a suitable welding wire until stop in the hole -2-. – Remove the lock cylinder -1- from the steering lock housing. WARNING Risk of steering lock seizing.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Release the retainer in direction of -arrow A- and remove the Ignition Switch Key Lock Solenoid - N376- -2- from the steering lock housing -1- in direction of -arrow B-.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the Ignition/Starter Switch - D- -5- from the steering lock housing. The jeweler's screwdriver or wire hooks must remain inserted. Installing Install in the reverse order of removal while paying attention to the following: –...
Page 191
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Disconnect the connector -1-. – Remove the connector lock in the direction of the -arrow B- and press down. – Disconnect the connector -2-. – Push the connector lock in the direction of the -arrow C- and disconnect the connector -3-.
Page 192
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the bolt -2- on the bottom. – Remove the steering column switch module -1-. Installing Install in the reverse order of removal while paying attention to the following: –...
Page 193
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Disconnect the connector -1-. – Remove the connector lock in the direction of the -arrow B- and press down. – Disconnect the connector -2-. – Push the connector lock in the direction of the -arrow C- and disconnect the connector -3-.
Page 194
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Slightly remove the steering column switch module -2-. – Push the release -3- in the direction of the -arrow B-. – Remove the steering column switch module -2-.
Page 196
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Push the connector lock in the direction of the -arrow B- and disconnect the connector -2-. – Push the connector lock in the direction of the -arrow C- and disconnect the connector -3-.
Page 197
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the Steering Column Electronics Control Module - J527- -2- from the Steering Column Combination Switch - E595- . Installing Install in the reverse order of removal while paying attention to the following: –...
Page 198
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 WARNING Risk of destroying electronic components with static discharge. ♦ Before disconnecting the connector, discharge static elec‐ tricity from your body by touching a grounded vehicle component such as the door striker pin.
Page 199
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the connector lock in the direction of the -arrow F- and press down. – Disconnect the connector -6-. – Remove the screws -1-. – Remove the Steering Column Electronics Control Module - J527- -2- from the Steering Column Combination Switch - E595- .
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Before sliding the Steering Column Electronics Control Mod‐ ule - J527- -3- the following must be checked. ♦ The “arrows” -1- must align. ♦ The spiral spring -2- must be seen in the window between the “arrows”...
Page 201
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 8.7.2 Turn Signal Switch - E2- , Removing and Installing, Valeo Turn Signal Switch - E2- , Cruise Control Switch - E45- and the Windshield Wiper Intermittent Mode Switch - E22- together make up the Steering Column Combination Switch - E595- .
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Push the release -3- in the direction of the -arrow B-. – Remove the Steering Column Combination Switch - E595- -2-. Installing Install in reverse order of removal.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Position the steering wheel as far back as possible. Use the entire adjustment range of the steering column adjustment for this. – Remove the lower steering column trim panel. Refer to ⇒ Body Interior;...
Page 204
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Tighten the new bolts -arrows- until the head shears off. Rep. Gr.94 - Exterior Lights, Switches...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Removing – Turn off the ignition and all electrical equipment. – Remove the ignition key, if equipped. – Remove the trim panel under the instrument panel. Refer to ⇒...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the Front Parking Aid Warning Buzzer - H22- -3- with a narrow screwdriver -1- from the mount -2- in direction of -arrows-. – Remove the Front Parking Aid Warning Buzzer - H22- .
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Pry of the expanding clip -1 and 3-. – Remove the Rear Parking Aid Warning Buzzer - H15- -4-. – Disconnect the connector -2-. Installing Install in reverse order of removal.
Page 212
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the bolts between the bumper cover and lock carrier from below. – If equipped, remove the bolts -1-. – Detach the bumper cover -2- from the fender and remove in the direction of the -arrow A-.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Rear Parking Aid Sensor, Removing and Installing Removing – Turn off the ignition and all electrical equipment. – Remove the ignition key, if equipped. Outer Sensors The outer rear parking aid sensor can be remove and installed without removing the rear bumper.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 10.3 Front Sensor, Removing and Installing Removing – Turn off the ignition and all electrical equipment. – Remove the ignition key, if equipped. – Remove the wheel housing liner. Refer to ⇒ Body Exterior;...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 11.2 Control Module for Headlamp Range/ Cornering Lamp and Headlamp Range, Removing and Installing If the control module is being replaced, use the Vehicle Diagnostic Tester and select the “Replacing” function for the respective con‐...
Page 220
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Push the expanding clip -2- in the opening -3- on the control module -1-. – Lock the expanding clip by turning 90° in direction of -arrow-.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 12.3 Towing Recognition Control Module - J345- , Removing and Installing ⇒ “12.3.1 Towing Recognition Control Module J345 , Removing and Installing, Sedan”, page 215 ⇒ “12.3.2 Towing Recognition Control Module J345 , Removing and Installing, Wagon”, page 215...
Page 224
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the screws -1-. – Pull the vehicle tools bracket in the direction of -arrow A-. – Disconnect the connectors -2-. – Remove the vehicle tools bracket in the direction of -arrow B- from the side panel.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the bolt -3-. – Remove the Blind Spot Detection Control Module - J1086- / Blind Spot Detection Control Module 2 - J1087- -2- from the bracket -1-.
Page 231
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 1 - Volkswagen Logo ❑ The laser pointer is aligned on the center of the Volkswagen logo 2 - Calibration Tool - Wheel Center Mountings - VAS6350/1- ❑...
Page 232
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 10 - Catch Bracket ❑ To mount the Calibration Tool - Spacing Laser - VAS6350/2- for the distance measurement ❑ Distance to the Calibration Tool - Wheel Center Mountings - VAS6350/1- on the rear wheels: dimension -a- = 1700 ±...
Page 233
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Position the -VAS6350A- at distance -a- to the rear wheels. • Dimension -a- = 1700 ± 2 mm – Switch on the -VAS6350/2- with the button.
Page 234
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Secure the Calibration Tool - Lane Change Calibration Tool - VAS6350/4- to the Calibration Unit - VAS6350A- mount on the rear left side. • When installed correctly, the vehicle electrical system voltage line must be connected at bottom left of calibration device (as seen in direction of travel).
Page 235
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Check right and left distance between catch bracket on the Calibration Unit - VAS6350A- and measuring paddle -1- on wheel mountings again. • Specified value: 1700 ± 2 mm Blind Spot Detection Control Module, Calibrating.
Page 236
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 During the program sequence, there is a prompt to switch the Calibration Tool - Lane Change Calibration Tool - VAS6350/4- from the left to the right side of the Calibration Tool - VAS6350- .
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Removing – Turn off the ignition and all electrical equipment. – Remove the ignition key, if equipped. – Push the retaining tab -1- with a flat-head screwdriver and pry up the glove compartment lamp -2-.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 1.10 Left/Right Front Footwell Illumination Bulb -L151- / -L152- , Removing and In‐ stalling For a front footwell lamp the lamp must be replaced if there is a faulty LED.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Press the tabs -arrows- and remove the Central Locking -Safe- Indicator Lamp - K133- -1- from the door trim panel. – Release and disconnect the connector -1- from the Central Locking -Safe- Indicator Lamp - K133- -2-.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Disconnect the connector and remove the lamp. Installing Install in reverse order of removal. 1.13 Entry Lamp Bulb, Removing and Instal‐ ling Removing – Remove the front entry lamp. Refer to ⇒...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Caution There is a risk of damaging the fiber-optic cable. ♦ Only touch the fiber-optic cable on the light fittings in the area of the interior door mechanism.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Entry Lamp, Removing and installing. Refer to ⇒ “1.12 Left/Right Front Entry Lamp W31 / W32 , Removing and Installing”, page 245 1.18 Left/Right Rear Door Warning Lamp - W37- / -W38- , Removing and Installing The door warning lamp and the entry lamp make up one compo‐...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Push the retaining tab -1- with a flat-head screwdriver and pry up the Luggage Compartment Lamp - W3- -2-. – Disconnect the connector -3-. Installing Install in the reverse order of removal while paying attention to the following: –...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Pry up the heat shield -2- when necessary on both sides at both arrows -A-. – Remove the heat shield -2- from the Luggage Compartment Lamp - W3- -1-.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Caution Risk of damaging the component surfaces. ♦ When positioning a prying tool, put commercially available adhesive tape over the component in the visible area. Removing – Turn off the ignition and all electrical equipment.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Caution Risk of damaging the component surfaces. ♦ When positioning a prying tool, put commercially available adhesive tape over the component in the visible area. Removing – Turn off the ignition and all electrical equipment.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Removing – Turn off the ignition and all electrical equipment. – Remove the ignition key, if equipped. – Pry up the diffusion lens -3- for the Rear Interior Lamp - W43- using the -3409- .
Page 263
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Note The entire interior lamp must be replaced if there is a defective bulb in the Left Rear Interior Lamp - W47- / Right Rear Interior Lamp - W48- .
Page 264
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Unclip the interior lamp -1- at the pivot points -arrow- on both sides of the lamp out of the bracket -2- using the -3409- . – Disconnect the connector from the interior lamp.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 ♦ Child Safety Lock Button - E318- ❑ Removing and installing. Refer to ⇒ “2.19 Power Window Control Head in Driver Door E512 , Removing and Installing”, page 270 No Illustration ♦...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the bolt -1-. – Remove the trim -2- using the Headlamp Range Control Ad‐ juster - E102- from the instrument panel. – Release and disconnect the connectors.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Lift the driver side button module -1- or the front passenger side button module -2- upward from the center console. – Release and disconnect the connector -1-.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Removing – Turn off the ignition and all electrical equipment. – Remove the ignition key, if equipped. – Carefully release the retainers using a small screwdriver -arrows-.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the Power Window Control Head in Driver Door - E512- -2- from the trim -1-. Installing Install in reverse order of removal. – Perform a function test.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the Driver Interior Locking Button - E308- -1- from the Exterior Rearview Mirror Adjuster - EX11- -2- trim. Installing Install in the reverse order of removal while paying attention to the following: –...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 2.23 Driver and Front Passenger Door Con‐ tact Switch - F2- / -F3- , Removing and Installing The door contact switch is installed in the door lock and cannot be replaced individually when faulty.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the selector lever boot. Refer to ⇒ Rep. Gr. 34 ; Selector Mechanism; Selector Lever Handle, Removing and Installing . – Remove the Start System Button - E378- -1- from below out of the center console -2-.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 2.30 Front Interior Lamp/Reading Lamp, Re‐ moving and Installing Special tools and workshop equipment required ♦ Trim Removal Wedge - 3409- The switch module is a component of the Front Interior Lamp - WX1- and cannot be removed separately.
Page 284
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the ignition key, if equipped. – Pry the diffusion lens -1- with a narrow screwdriver in the di‐ rection of the -arrow A-. – Remove the diffusion lens -1- from the Rear Interior Lamp - WX2- -2-.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 2.32 Left/Right Front Reading Lamp Button - E633- / -E634- , Removing and Installing The Left Front Reading Lamp Button - E633- / Right Front Read‐ ing Lamp Button - E634- is a component of the Front Interior Lamp - WX1- and cannot be replaced separately.
Page 288
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the Front Interior Lamp - WX1- . Refer to ⇒ “2.30 Front Interior Lamp/Reading Lamp, Removing and In‐ stalling”, page 275 – Remove the screws -2-.
Page 289
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 3.3.2 Anti-Theft Alarm System Sensor - G578- , Removing and Installing, Ver‐ sion with Four Screws Special tools and workshop equipment required ♦ Trim Removal Wedge - 3409- Caution Risk of damaging the component surfaces.
Page 290
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the individual sensor -1- from the roof module. Installing Install in the reverse order of removal while paying attention to the following: If the Anti-Theft Alarm System Sensor - G578- is being replaced, then it must be adapted using the Vehicle Diagnostic Tester .
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Driver Assistance Systems Front Camera ⇒ “4.1 Driver Assistance Systems Front Camera, Removing and Installing”, page 283 Driver Assistance Systems Front Cam‐ era, Removing and Installing Removing –...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Cigarette Lighter - U1- , Removing and Installing All instructions and information on this chapter. Refer to ⇒ Elec‐ trical Equipment General Information; Rep. Gr. 96 ; Cigarette Lighter and Socket .
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the right luggage compartment side trim panel. Refer to ⇒ Body Interior; Rep. Gr. 70 ; Luggage Compartment Trim Panels; Luggage Compartment Side Trim Panel, Removing and Installing .
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 1.1.2 Relay Carrier and Instrument Panel/A-Pillar Fuse Panel Note The Sedan is shown. The Wagon is identical. 1 - Bracket ❑ For Parking Aid Control Module - J446- / Parallel...
Page 299
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Push the release button in direction of -arrows-. – Remove the engine compartment E-box cover -1-. – Release the mounting tab -2- with a screwdriver, and remove the front cover -1- upward in direction of -arrow-.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Overview - Data Bus On Board Diagnostic Interface 1 - Connector ❑ For Data Bus On Board Diagnostic Interface - J533- 2 - Data Bus On Board Diag‐...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Release and disconnect the connectors -1, 2, and 3-. – To disconnect the connector press the circlip -1-. – Pivot the retaining bracket in direction of -arrow- and remove the connector.
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Removing – Turn off the ignition and all electrical equipment. – Remove the ignition key, if equipped. – Remove the footwell cover on the driver side. Refer to ⇒ Body Interior;...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – Remove the bolts -2, 3, and 6-. – Push the bracket -1- as far as possible out of the central tube until the alignment pins -4- and -5- are disengaged.
Page 311
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 – If equipped: remove the Parking Aid Control Module - J446- / Parallel Parking Assistance Control Module - J791- . Refer to ⇒ “9.2 Parking Aid Control Module J446 , Removing and In‐...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Connector Housings, Releasing and Disassembling All instructions and information on this chapter. Refer to ⇒ Elec‐ trical Equipment General Information; Rep. Gr. 97 ; Connectors . 4. Connector Housings, Releasing and Disassembling...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Fiber-Optic Cable All instructions and information on this chapter. Refer to ⇒ Elec‐ trical Equipment General Information; Rep. Gr. 97 ; Connectors . 6. Fiber-Optic Cable...
Golf 2015 ➤ , Golf Variant 2015 ➤ Electrical Equipment - Edition 12.2015 Revision History DRUCK NUMBER: K0059241521 Fac‐ Edit Notes Quality tory Edi‐ Type ed‐ Checke Edi‐ tion d By tion 12.2 1/15/ Fac‐ Added MRPs and deleted Jim H...
Page 318
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Page 319
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Page 320
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.