Mitsubishi Electric M700V Series Programming Manual page 267

13. Program Support Functions
Operation1
Operation2
Operation3
Fig. 2 Operation in fixed cycle modal
Setting values of synchronous tap in-position check parameters and tap axis movement
(1) Synchronous tap in-position check settings
#1223 aux07
Bit3 Bit4
Synchronous
tapping At hole
in-position bottom
R point
check
0 —
1 —
1 1
1 1
1 0
1 0
1 1
1 1
1 0
1 0
(Note 1) The I point refers to the initial point.
Operation5
-10.
-50.
Opera-
tion6
Opera-
tion7
Operation4
Operation8
Bit5 Bit2
"P" designation of
→
G84/G74 command
At I point
R point
— —
No "P" designation
— —
Example: G84 F1. Z-5.
"P" designation
Example: G84 F1. Z-5.
1 1
"P" designation
Example: G84 F1. Z-5.
0 1
"P" designation
Example: G84 F1. Z-5.
1 1
"P" designation
Example: G84 F1. Z-5.
0 1
"P" designation
Example: G84 F1. Z-5.
1 0
"P" designation
Example: G84 F1. Z-5.
0 0
"P" designation
Example: G84 F1. Z-5.
1 0
"P" designation
Example: G84 F1. Z-5.
0 0
Operation9
-10.
Opera-
tion10
Opera-
tion11
Opera-
tion12
Carry out in-position check at I point → R point/R
—
point/hole bottom.
Hole bottom:
R point:
I point → R point:
S1000 R-5.
Hole bottom:
R point:
S1000 PO
I point → R point:
R-5.
Hole bottom:
R point:
S1000 PO
I point → R point:
R-5.
Hole bottom:
R point:
I point → R point:
S1000 PO
R-5.
Hole bottom:
R point:
I point → R point:
S1000 PO
R-5.
Hole bottom:
R point:
S1000 PO
I point → R point:
R-5.
Hole bottom:
R point:
S1000 PO
I point → R point:
R-5.
Hole bottom:
R point:
I point → R point:
S1000 PO
R-5.
Hole bottom:
R point:
I point → R point:
S1000 PO
R-5.
255
13.1 Fixed Cycles
Operation
,I
pattern
Operation 1 Valid
Operation 2 – Invalid
Operation 3 – Invalid
Operation 4 –
Operation 5 Invalid
Operation 6 – Invalid
Operation 7 – Invalid
Operation 8 –
Operation 9 Valid
Operation 10 – Invalid
Operation 11 – Invalid
Operation 12 –
In-position check
during synchronous tapping
Do not carry out in-position check.
Do not carry out in-position check.
Do not carry out in-position check.
Carry out in-position check by tap
in-position width.
Carry out in-position check.
Carry out in-position check.
Carry out in-position check by tap
in-position width.
Do not carry out in-position check.
Carry out in-position check.
Do not carry out in-position check.
Carry out in-position check.
Carry out in-position check.
Do not carry out in-position check.
Do not carry out in-position check.
Carry out in-position check.
Carry out in-position check by tap
in-position width.
Carry out in-position check.
Do not carry out in-position check.
Carry out in-position check by tap
in-position width.
Do not carry out in-position check.
Do not carry out in-position check.
Do not carry out in-position check.
Carry out in-position check.
Do not carry out in-position check.
Do not carry out in-position check.
Do not carry out in-position check.
Do not carry out in-position check.
,J
–
Valid
–
Valid
–
Valid