Table of Contents
Advertisement
7.5 Inverse Time Feed; G93 .....................................................................................................112
7.6 Feedrate Designation and Effects on Control Axes ............................................................116
7.7 Rapid Traverse Constant Inclination Acceleration/Deceleration .........................................120
7.8 Rapid Traverse Constant Inclination Multi-step Acceleration/Deceleration ........................122
7.9 Exact Stop Check; G09.......................................................................................................131
7.10 Exact Stop Check Mode; G61...........................................................................................134
7.11 Deceleration Check...........................................................................................................134
7.11.1 G1 -> G0 Deceleration Check.....................................................................................136
7.11.2 G1 -> G1 Deceleration Check.....................................................................................137
7.12 Automatic Corner Override ...............................................................................................138
7.13 Tapping Mode; G63 ..........................................................................................................143
7.14 Cutting Mode; G64 ............................................................................................................143
8. Dwell...........................................................................................................................................144
8.1 Per-second Dwell ; G04 ......................................................................................................144
9. Miscellaneous Functions .........................................................................................................146
9.1 Miscellaneous Functions (M8-digits BCD) ..........................................................................146
9.2 Secondary Miscellaneous Functions (B8-digits, A8 or C8-digits) .......................................148
9.3 Index Table Indexing...........................................................................................................149
10. Spindle Functions...................................................................................................................151
10.1 Spindle Functions (S6-digits Analog) ................................................................................151
10.2 Spindle Functions (S8-digits) ............................................................................................151
10.3 Constant Surface Speed Control; G96, G97.....................................................................152
10.3.1 Constant Surface Speed Control ................................................................................152
10.4 Spindle Clamp Speed Setting; G92 ..................................................................................153
10.5 Spindle/C Axis Control ......................................................................................................154
10.6 Multiple Spindle Control ....................................................................................................157
10.6.1 Multiple Spindle Control II ...........................................................................................158
11. Tool Functions (T command).................................................................................................160
11.1 Tool Functions (T8-digit BCD)...........................................................................................160
12. Tool Compensation Functions ..............................................................................................161
12.1 Tool Compensation ...........................................................................................................161
12.2 Tool Length Compensation/Cancel; G43/G44 ..................................................................165
12.3 Tool Length Compensation in the Tool Axis Direction ; G43.1/G44..................................168
12.4 Tool Radius Compensation; G38, G39/G40/G41,G42......................................................175
12.4.1 Tool Radius Compensation Operation........................................................................176
12.4.2 Other Commands and Operations During Tool Radius Compensation ......................185
12.4.3 G41/G42 Commands and I, J, K Designation.............................................................194
12.4.4 Interrupts During Tool Radius Compensation.............................................................200
12.4.5 General Precautions for Tool Radius Compensation..................................................202
12.4.6 Changing of Compensation No. During Compensation Mode ....................................203
12.4.7 Start of Tool Radius Compensation and Z Axis Cut in Operation...............................205
12.4.8 Interference Check .....................................................................................................207
12.4.9 Diameter Designation of Compensation Amount........................................................214
12.4.10 Workpiece Coordinate Changing During Radius Compensation ..............................216
12.5 Three-dimensional Tool Radius Compensation ; G40/G41,G42.......................................218
12.6 Tool Position Offset; G45 to G48 ......................................................................................229
12.7 Programmed Compensation Input; G10, G11.1................................................................236
12.8 Compensation Data Input to Variable by Program; G11...................................................241
12.9 Inputting the Tool Life Management Data; G10, G11 .......................................................242
12.9.1 Inputting the Tool Life Management Data by G10 L3 Command................................242
12.9.2 Inputting the Tool Life Management Data by G10 L30 Command..............................244
12.9.3 Precautions for Inputting the Tool Life Management Data..........................................247
Hide quick links:
Advertisement
Table of Contents
