Custom Panel Dimensions - Monogram ZIF36N RH Custom Options Manual And Installation Instructions

10-3/4" Max.
10" Min.
24-3/4"
26-3/4"
73-1/2"
4"
*Finished Width
2 1/2"
7"
Locate Grounded
Electrical outlet
5"
Within Solid
84 1/2" max Area Above
83 1/2" min
Finished
Opening
Locate Freezer Water
Supply Within
Shaded Aarea
5"
3 1/2"
* 36" Min. for a flush installation into an enclosure.
* 35-1/2" Min. for a semi-flush installation into an enclosure.
Note: Additional cutout width may be required when side panels are
used. Add side panel thickness to the finished cutout width to
calculate rough-in width. See installation examples, pages 4 and 5.
Clearances:
When installed into a corner: Allow 15" clearance on the
hinge side for a 130° opening and full extension of bottom
pans and pan removal.
Two products installed side-by-side, both with hinges on left
sides (or right sides) will require a 2" min. clearance
between the products. The 2" min. separation will prevent
one door handle striking the handle on the opposite product.

Custom Panel Dimensions

ZIR36N Refrigerator
ZIF36N Freezer
35" Case
36" Overall
Design Information
Designed to be installed flush or semi-flush with sur-
rounding cabinetry. Cutout dimensions, clearances and
side panel sizes are determined by the many installation
options available. Side panels must be used whenever the
sides of the refrigerator will be exposed. Side panels are
not required when installed into an enclosure or between
pantry and oven cabinets. IMPORTANT - Side panels, 1/2"
minimum thickness are required when using FRAMELESS
84-1/2" Max.
CABINETS.
83-1/2" Min.
• Field installed custom panels, Lexan
panels are required. The door and grille panel sizes vary
to accommodate the kit being used.
• The supplied toekick is vented and must remain
unobstructed for proper air circulation.
Optional Panel Kits:
• ZWBR36: Black Lexan
• ZWWR36: White Lexan
• ZWSR36: Stainless Steel Panel Kit
Optional Custom Trim Kits:
• ZKHR1: For installation of a custom handle of your
Wall View choice onto a 1/4" Panel.
(not to Scale)
• ZKTR36LH or ZKTR36RH: For installation of a 3/4" thick
custom panel.
• ZKHTR1: For installation of a custom handle of your
choice onto a 3/4" thick panel. (This kit must be used in
combination with ZKTR36LH or ZKTR36RH).
• ZKHRSS1: Tubular Stainless Steel handle for 1/4" thick
panel.
74" From
• ZKHTRSS1: Tubular Stainless Steel handle for 3/4" thick
Floor to
panel.
Bottom of
Electrical Area • ZGC2: 1/4" grille panel frame side pieces for 83-1/2" and
84-1/2" installation heights. (Factory set for 84").
• ZWT1: White toekick (supplied toekick is black).
• ZFC1: Trim strip for side-by-side installation of
two products.
5"
3 1/2"
• ZUG75: Unified 3/4" Grille Panel for side by side
installations. This kit must be used in combination with
ZKTR36LH and ZKTR36RH kits.
Additional Specifications
• A 115 volt 60Hz., 15 or 20 amp power supply is required.
An individual properly grounded branch circuit or circuit
breaker is recommended. Install a properly grounded 3-
prong electrical receptacle recessed into the back wall.
Electrical must be located on rear wall as shown.
• Water line can enter opening through the floor or back
wall. The water line should be 1/4" O.D. copper tubing
between the cold water line and water connection
location, long enough to extend to the front of the
refrigerator. Installation of an easily accessible shut off
valve is recommended.
36" Refrigerators, Freezers
®
or stainless steel
®
Panel Kit
®
Panel Kit
7