Installation Instructions - Monogram ZIF36N RH Custom Options Manual And Installation Instructions

Step 1
Remove
Packaging
• Remove outer carton.
• Slide out back corner posts (2).
• Slide carton off top of cabinet.
NOTE: IT IS NOT NECESSARY TO LAY CABINET DOWN
IN ORDER TO REMOVE SKID!
• The unit is secured to the skid with 4 slotted tie-down
• Protect the flooring. Cut a large piece of the card-
• Support blocks on the bottom must be removed before
• A cold water supply is required for automatic icemaker
Step 2
Install
Water Line
• Route 1/4" OD copper tubing between house cold
• Copper tubing should be long enough to extend to the
Shut off the main water supply.
Turn on the nearest faucet long enough to clear the line
of water.
• Install a shut-off valve between the icemaker water
NOTE: It is best to install the valve into a vertical water
pipe. If installed into a horizontal water pipe, make the
connection at the top or side, rather than at the bottom,
to avoid drawing off any sediment from the water pipe.
• Drill a 1/4" hole in the water pipe.
• Fasten the shut-off valve to the pipe with pipe clamp.
• Tighten the clamp screws until the sealing washer
• Place a compression nut and ferrule (sleeve) onto the
• Turn on the main water supply and flush debris from
NOTE: Saddle type shut-off valves are included in many
water supply kits. Before purchasing, make sure a
saddle type valve complies with local plumbing codes.
CAUTION
Refrigerator and freezer is much heavier at the top
than at the bottom – be careful when moving. When
using a hand truck, handle from side only.
PRUDENCE
Le réfrigérateur est beaucoup plus lourd en haut
qu'en bas. Il faut être prudent lors des
déplacements. Si un diable est utilisé, il faut
soulever le réfrigérateur sur le côté seulement.
– Carefully cut banding at the top and bottom.
straps. First remove the 5/16" bolts from the base
channels in the tie-downs, then remove the 7/16" bolts
securing the straps to the skid.
board carton and place under the product.
sliding unit off skid. Remove support blocks by
carefully tilting cabinet to side and sliding out.
operation. The water pressure must be between 20 and
120 p.s.i.
water line and the water connection location.
front of the refrigerator. Allow enough to accommodate
bend leading into the water valve.
valve and cold water pipe in a basement or cabinet.
The shut-off valve should be located where it will be
easily accessible.
begins to swell. Do not over tighten.
end of the tubing and connect it to the shut-off valve.
Make sure the tubing is fully inserted into the valve
and ferrule is tightened.
the line. Run about a quart of water through the tubing
into a bucket. Shut off water at the shut-off valve.
Installation
36" Refrigerators, Freezers
• Carefully slide until off skid.
CAUTION
DO NOT ATTEMPT TO ROLL UNIT OFF SKID.
PRUDENCE
IL NE FAUT PAS ESSAYER DE FAIRE ROULER LE
RÉFRIGÉRATEUR POUR L'ENLEVER DE LAY PALETTE.
Floor
Copper Tubing
Washer
Saddle Type
Shutoff Valve
Packing Nut
Outlet Valve
• Install optional water filter in the water line near the
refrigerator. A water filter is recommended in areas
where water supply contains sand or particles.
Installation instructions are packed with the filter.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
7/16" Bolt
Inlet End
Pipe Clamp
Compression Nut
Ferrule
(Sleeve)
13