Related Manuals for Monogram ZIRP360NXARH
Summary of Contents for Monogram ZIRP360NXARH
- Page 1 Installation Instructions 36" Built-In All-Refrigerators and All-Freezers 31-/461/48 22/402601PO01 06-08 JR monogram.com...
-
Page 2: Table Of Contents
Read these instructions completely and carefully. installation is the responsibility of the installer. Product failure due to improper installation is not covered •IMPORTANT- Save these instructions under the GE Appliance Warranty. See the Owner's forlocal i nspector's use.Observeall governing Manualfor warranty information. codes and ordinances. -
Page 3: Theinstallation Space
The water line should be 1/4" O.D. Allow 25" minimum cleoronce for o full copper tubing or GE QuickConnect T"kit between the 1]0 ° door swing. Allow 15" for pon removal. cold water line and water connection location, long For o go°... - Page 4 Design Guide CLEARANCES 4" Min. to Wall 2" 130 ° Door Swing 0 DoorSwing 36-3/4" ..130 ° ..Clearances for two products installed side-bg-side These units are equipped with a 2-position door stop. with the same (left or right) door swing The factory set 1]0 °...
-
Page 5: 130° Door Swing
Design Guide Frameless Cabinets: The case trim overlaps cabinets at the top and sides. Therefore, frameless cabinets mag require filler strips to )revent interference with cabinet door Refrigerator swing. The opening must allow for filler strips. 23-7/8"From or Freezer Rearof Unit 3"... -
Page 6: 90 ° Door Swing
Design Guide Frameless Cabinets: Refrigerator or Freezer The case trim overlaps CaseTrim cabinets at the top and sides. Therefore, frameless cabinets mag require filler strips to prevent interference with cabinet door swing. 23-7/8" The opening must allow From Rearof for filler strips. Unit Door Top View... -
Page 7: Customizationbasics
Design Guide CUSTOMIZATION BASICS: Framed Or Overlag Panels, Custom Handles and Accessorg Kits Professional Stgle Stainless Steel Models Overlag panels Stainless steel wrapped refrigerators have beveled edges You may also choose to install custom overlay panels and professional-stgle handles. These models are shipped from gour cabinet manufacturer. -
Page 8: Panel Dimensions
Design Guide 1/4" FRAMED PANEL DIMENSIONS If you choose to install framed panels, they must be cut to 5/16" the dimensions shown. The panels will slide into the frame Trim on the door and grille. Door Reveal If the custom panel is less than 1/4" thick and if it fits loosely in the door frame, it can be backed up with a piece 1/4"... -
Page 9: Sidepanels
Desiqn Guide SIDE PANELS ZUG2 GRILLE PANEL DIMENSIONS Side panels must be used whenever the sides The ZUG2 unified grille panel kit provides of the unit will be exposed, The 1/4" side panels will slip for the installation of a framed or overlay grille panel. into the side case trim. -
Page 10: Grounding The Unit
Bucket _ 1/4", 1/2", 5/16", 7/16" socket 4 Washers (Securedto side of unit.) MATERIALS REQUIRED Level • 1/4" copper water line tubing or GE SmartConnect T" Safety glasses Refrigerator Tubing kits Appliance • Water shut-off valve (optional but recommended) hand truck •... -
Page 11: Step 2, Install Water Line
• A cold water supply is required for automatic icemaker operation. The water pressure must be between 40 and 120 p.s.i. • Route 1/4" OD copper or GE SmartConnect T" plastic tubing between house cold water line and the water connection location. -
Page 12: Step 4, Install Anti-Tip Bracket
Installation Instructions STEP 4 INSTALL ANTI-TIP BRACKET WARNING: ANTI-TIP PRECAUTIONS The unit is top-heavy and must be secured to prevent the possibility of tipping forward. ATTENTION: PRECAUTIONS CONTRE LESBASCULEMENTS L'appareil m_nager est beaucoup plus Iourd en haut et il faut le maintenir en place pour _viter la possibilit_ de son basculement vers I'avant. - Page 13 Installation Instructions STEP 4 INSTALL ANTI-TIP BRACKET (cont.} Install Screwsand Bolts: Install Wall Toggles: • Have someone holdthe wallbracket centered The wall toggles and bolts con be ordered as Service Kit #WR49X10193. Wall toggles ore installed in the in place with each of the holes aligned with drywall and metal studs for stability.
- Page 14 Installation Instructions Power Cord STEP 4 INSTALL ANTI-TIP BRACKET Locate the power cord inside the left cavitg. If it has (cont.) not been adjusted so the plug is easilg accessible, do so now. Remove Grilles for Access to Power Cord and Anti-tip Locking Hooks "L"...
-
Page 15: Step 5, Level Unit
Installation Instructions STEP 5 LEVEL UNIT All models have 4-point leveling. The front is supported bu leveling legs; the rear is supported bu adjustable wheels. Both are accessible from the front of the unit. • To level the back of the unit, turn the 7/16" hex nut located above the front wheels. -
Page 16: Step 6, Secure Unit To Wall
Installation Instructions STEP 61SECURE UNIT TO WALL • The "L" rods con be found in the upper left and right corners of the unit in the access comportment. Look through the access comportment to make i - s-:.- ....i:: _'_-__ -_-_-, , - ..... -
Page 17: Step 7, Adjust Door Swing
Installation Instructions [STEP 7 ADJUST DOOR SWING STEP 8 INSTALL GRILLE PANEL (TRIMMED MODELS ONLY) NOTE:This refrigerotor hos o 2-position door stop. When spoce does not ollow the door to swing open • Roise the occess ponel to the stop position. fullg to 130°, gou mog chonge the door swing to o 90°... -
Page 18: Step 9, Install Framed Panels
Installation Instructions Right hand models shown. Use the same instructions [STEP 9] INSTALL FRAMED PANELS for left hand models. (TRIMMED MODELS ONLY) IF YOU ARE INSTALLING OVERLAY PANELS, GO TO STEP IOA. Handle Door Trim Trim Door useFr0ntH k\\\\\\\\\\\\\\\\\\\%/ to SecureTrim Rear Holes Standardsuppliedhandleshown to Secure Handle... -
Page 19: Step 9A Install Overlay Panels
Installation Instructions Right hand models shown. Use the same instructions STEP 9A INSTALL OVERLAY PANELS for left hand models. Door T rim Handle Trim Door Move Forward For3/4" Panel Use Front Holes to Secure Handle UseRearHoles to SecureTrim Supplied h andle shown intheoverlay panel p osition. -
Page 20: Step 10 Connect Water Supply
• Turn on the water to check for leaks. I STEP 12 INSTALL TOEKICK GE SmartConnect Tubing: • Locate the supplied toekick (shipped taped to the side • Insert the molded end of the tubing into of the product). - Page 21 Notes...
- Page 22 Notes...
- Page 23 Notes...
- Page 24 1.800.444.1845. NOTE: Product improvement is a continuing endeavor General Electric. Therefore, materials, appearance specifications are subject to change without notice. GE Consumer & Industrial ]1-46148 Appliances 22402601PO01 General Electric Company Louisville, KY/40225 06-08 JR ge.com Printed in the United States...
Need help?
Do you have a question about the ZIRP360NXARH and is the answer not in the manual?
Questions and answers