Routine Call - Icom IC-M802 Instruction Manual

7
CALL PROCEDURE

■ Routine call

When you use DSC for general selective calling, use
"Routine" as the category.
q Push [MODE
set
w Rotate [CH] to select "Individual" then push
[ENT].
e Select "Routine" as the category using [CH],
then push [ENT].
* * * * * * I n d i v i d u a l * * * * * *
- - - - - - - C a t e g o r y - - - - - - -
R o u t i n e
Ç
S a f e t y
U r g e n c y
D i s t r e s s
S E L
r Select the desired 9-digit ID code, then push
[ENT].
• Use [CH] to select the ID code when the desired ship's
ID is pre-programmed.
* * * * * * I n d i v i d u a l * * * * * *
- - - - - - A d d r e s s I D - - - - - -
M a n u a l s e t
Ç
I C - M 8 0 2 - 1
I C - M 8 0 2 - 2
I C - M 8 0 2 - 3
I C - M 8 0 2 - 4
I C - M 8 0 2 - 5
S E L
• Select "Manual set" with [CH] then push [ENT].
After that, enter the desired 9-digit ID using the keypad.
* * * * * * I n d i v i d u a l * * * * * *
- - - - - - A d d r e s s I D - - - - - -
t Select either "
Frequency
[CH], then push [ENT].
* * * * * * I n d i v i d u a l * * * * * *
- - - - - - - M e s s a g e - - - - - - - -
F r e q u e n c y
Ç
P o s i t i o n
S E L
- When "Frequency" is selected, go to step y.
32
] to select the DSC menu.
O K
1 2 3 4 5 6 7 8 9
1 2 3 4 5 6 7 8 8
1 2 3 4 5 6 7 8 7
1 2 3 4 5 6 7 8 6
1 2 3 4 5 6 7 8 5
O K
9 8 7 6 5 4 3 2 1
O K
" or "
Position
O K
- When "Position" is selected, enter the posi-
tion information (latitude and longitude) using the
keypad, then push [ENT].
* * * * * * I n d i v i d u a l * * * * * *
- - R T w i t h P o s n u m b e r - -
y Rotate [CH] to select the desired pre-programmed
traffic frequency, or "Manual set" then push
[ENT].
✔ When pre-programmed traffic frequency is se-
lected, go to step i.
* * * * * * I n d i v i d u a l * * * * * *
- - T r a f f i c f r e q u e n c y - - -
M a n u a l s e t
Ç
T : 4 5 6 7 . 0 k H z I C - M 8 0 2 - 1
R : 4 5 6 7 . 0 k H z
T : 1 2 3 4 5 . 0 k H z I C - M 8 0 2 - 2
R : 1 2 3 4 5 . 0 k H z
u Enter the desired transmit and receive traffic fre-
quency using the keypad, then push [ENT].
• One of the voice channels, such as Tx/Rx: 2082.5 kHz,
4146.0 kHz, should be used.
* * * * * * I n d i v i d u a l * * * * * *
- - T r a f f i c f r e q u e n c y - - -
" using
i Rotate [CH] to select the desired pre-programmed
calling frequency, or "Manual set" then push
[ENT].
✔ When the pre-programmed call frequency is se-
lected, go to step !0 .
* * * * * * I n d i v i d u a l * * * * * *
- - - - C a l l f r e q u e n c y - - - -
M a n u a l s e t
Ç
T : 2 3 4 5 . 0 k H z I C - M 8 0 2 - 1
R : 2 3 4 5 . 0 k H z
T : 2 1 7 7 . 0 k H z S H I P
R : 2 1 7 7 . 0 k H z
L a t i t u d e 3 4 3 4 ' N
L o n g i t u d e 1 3 5 3 4 ' E
N u l l O K
S E L O K
T X : _ 4 5 6 7 . 0 k H z
R X : _ 4 5 6 7 . 0 k H z
S E L O K
S E L O K