Position And Time Programming - Icom IC-M802 Instruction Manual

6
DSC PREPARATION

■ Position and time programming

When no GPS receiver is connected to the [GPS] con-
nector, the position and the UTC time should be manu-
ally input for the DSC operation.
q The transceiver must be OFF. Then, while holding
down [MODE
set
set mode.
w Rotate [GRP] to select the "GPS DISPLAY" then
rotate [CH] to select the desired position display
type either Simple or Detail.
* * * S E T M O D E * * *
S I M P L E
ÇÇ
D E T A I L
I T E M
e Rotate [GRP] to select the "OFFSET TIME", then
rotate [CH] to set the time difference between local
and the UTC time, between –12 to +12 hours, in
10 minute steps.
* * * S E T M O D E * * *
I T E M
r Turn OFF the power once, then ON again to exit
the Quick set mode.
• Simple position display
R X
1 2 . 3 4 5 . 0
S P
E x i t
16 16
] push [POWER] to enter initial
[MODE ] [POWER]
SET
S E L
S E L
J 3 E
M N L L a t 3 4 3 4 ' N
L o n 1 3 5 3 4 ' E
1 2 : 3 4
IMPORTANT!
The manually programmed position and the UTC
time settings will be cleared once the power is
turned OFF. They are never renewed during the voy-
age when the position is set manually.
✔ When a GPS receiver is connected to [GPS],
the following steps are not necessary.
t Push [DSC] to select the DSC watch mode.
y Push [MODE ] to open the DSC menu.
set
• The DSC menu is displayed, as shown below.
u Rotate [CH] to select "Position," then push
[ENT].
* * * * * * * D S C M E N U * * * * * * *
- - - - - - - - S e l e c t - - - - - - - -
P o s i t i o n
Ç
I n d i v i d u a l
G r o u p
G e o g r a p h i c a l
P o s i t i o n R E Q
D i s t r e s s
S E L O K
i Enter your position and the UTC time using the
keypad, then push [ENT].
• Push [3 ] for the 'East,' [9
scan
for the 'North' and [7 ] for the 'South' setting.
l o
• The degree and minute digits can only be entered
when "DETAIL" is selected as the position display in
step w. The seconds digit shows only "0".
• Rotate [CH] to move the cursor.
* * * * * * * P o s i t i o n * * * * * * *
- - - P o s i t i o n & t i m e - - - -
L a t i t u d e
L o n g i t u d e
U T C
N u l l
o Push [ENT] to program the position and time.
• Return to the "DSC MENU" display as in step u.
!0 Push [MODE ] to exit the DSC menu.
set
• Rotate [CH] to select "Exit", then push [ENT] will
also exit the set mode.
• "MNL" appears instead of "GPS."
• Detail position display
R X
1 2 . 3 4 5 . 0
S P
E x i t
] for the 'West,' [6 -
h i rf g
3 4 3 4 . 3 4 3 N
1 3 5 3 4 . 3 4 3 E
1 2 : 3 4
O K
J 3 E
3 4 3 4 . 0 0 0 N
M N L
1 3 5 3 4 . 0 0 0 E
1 2 : 3 4
]