Position Request Call; Distress Call - Icom IC-M802 Instruction Manual

■ Position request call

q When "Position REQ" is displayed, as shown
below, push [ENT].
* * * * * * * * * * * * * * * * * * * * * * * *
* P o s i t i o n R E Q
* I C O M M 8 0 2
* * * * * * * * * * * * * * * * * * * * * * * *
E x i t
Calling station's name appears when
the same ID is preprogrammed.
w Push [ENT] to display the call contents for ac-
knowledgement preparation.
* * * * * * R X m e m o r y * * * * * * *
- - - - - P o s i t i o n R E Q - - - - -
F r o m : I C O M M 8 0 2
R X F r e q : T X 1 2 3 4 5 . 0 k H z
R X 1 2 3 4 5 . 0 k H z
C a n c e l

■ Distress call

When receiving a distress call, an emergency
q
alarm sounds and the display below appears.
* * * * * * * * * * * * * * * * * * * * * * * *
* D i s t r e s s
* 1 2 3 4 5 6 7 8 9
* * * * * * * * * * * * * * * * * * * * * * * *
E x i t
w Push [CANCEL/CALL] to stop the alarm.
• One distress call sequence is sent 5 times repeat-
edly within approximately 30 seconds. The emergency
alarm sounds at each reception.
e Push [ENT] to set the transceiver to the distress
phone frequency, then monitor the communication
from the coast station to the ship in distress.
< T r a f f i c >
R X
G P S
S P
E x i t
*
*
A C K
A C K
*
*
T r a f f i c
J 3 E
L a t 3 4 3 4 ' N
L o n 1 3 5 3 4 ' E
1 2 : 3 4
WHEN RECEIVING A CALL
e Verify your position and time, then push [ENT].
• When the position or time requires a change, use the
keypad and [CH] for settings.
• [CH] moves the cursor.
* * * * * P o s i t i o n A C K * * * * *
- - - P o s i t i o n & t i m e - - - -
L a t i t u d e
L o n g i t u d e
U T C
N u l l
r Hold down [CANCEL/CALL] 1 second to transmit
the Position request acknowledgement.
• Returns to DSC watch mode after the transmission,
automatically.
* * * * * P o s i t i o n A C K * * * * *
- - - - - - - - - C a l l - - - - - - - - -
T o : I C O M M 8 0 2
P o s i t i o n : L a t 3 4 3 4 . 3 4 3 N
L o n 1 3 4 3 4 . 3 4 3 E
U T C 1 2 : 3 4
C a l l F r e q : T X 1 2 3 4 5 . 0 k H z
R X 1 2 3 4 5 . 0 k H z
C a l l
r Select the received distress call memory channel
to check the position of the ship in distress.
➥ Push [FREQ/CH] then [RX
memory" screen.
➥ Select "Distress" with [CH] then push
[ENT].
➥ Push [ENT] again.
• The received distress call memory is displayed at
the top line with "*" symbol.
• When the ship is close to you, communication should
be monitored continuously.
• The traffic frequency is monitored even when the mem-
ory contents are displayed.
* * * * * * R X m e m o r y * * * * * * *
- - - - - - - D i s t r e s s - - - - - - -
D i s t r e s s I D : 1 2 3 4 5 6 7 8 9
U n d e s i g n a t e d
P o s i t i o n : L a t 3 4 3 4 . 3 4 3 N
L o n 1 3 4 3 4 . 3 4 3 E
U T C 1 2 : 3 4
T r a f f i c : R a d i o t e l e p h o n e
T X
R X
R X F r e q : T X
R X
D E L C a n c e l
8
3 4 3 4 . 3 4 3 N
1 3 4 3 4 . 3 4 3 E
1 2 : 3 4
O K
] to select "RX
clar
2 1 8 2 . 0 k H z
2 1 8 2 . 0 k H z
2 1 8 7 . 5 k H z
2 1 8 7 . 5 k H z
O K
8
41