Page 1 BARCO PROJECTION SYSTEMS GRAPHICS 8200LC R9001338 R9001339 OWNER'S MANUAL Art. No. :R5975288A Date: 150597...
Page 2 Due to constant research, the information in this manual is subject to change without notice. Produced by BARCO NV, May 1997. All rights reserved. Trademarks are the rights of their respective owners. Printed in Belgium...
Page 3: Table Of Contents
Table of Contents WARNINGS & SAFETY INSTRUCTIONS ............................1-1 AVERTISSEMENTS & PRESCRIPTIONS DE SECURITE ....................... 1-1 UNPACKING & DIMENSIONS ................................. 2-1 Unpacking ..................................... 2-2 Projector dimensions ................................2-3 Battery installation in the RCU.............................. 2-4 INSTALLATION GUIDELINES ................................. 3-1 Installation guidelines ................................3-2 * Environment ..................................
Page 4 Table of Contents RGB analog input module..............................7-6 Component input module..............................7-9 RGB3S/RG3sB input module.............................. 7-11 Connecting a computer, e.g. IBM PC (or compatible), Apple Macintosh to the RS 232 input of the projector....... 7-13 Set up of the baud rate for communication with a computer....................7-13 Connecting a RCVDS 05 to the projector.
Page 5 Table of Contents Gamma .................................... 11-15 Geometry ..................................11-16 Shift ....................................11-16 Size ....................................11-17 Side keystone ................................... 11-18 Blanking ................................... 11-19 Options ..................................... 11-21 INSTALLATION ..................................... 12-1 Starting up the Installation Mode ............................12-2 Input Slots ..................................12-3 Convergence ..................................12-4 Configuration ..................................
Page 6 Table of Contents Hardwired RCU................................... 14-2 RCVDS 05 ..................................14-3 VS05 ....................................14-3 MAGIK Interface ................................. 14-4 Adapter and communication cables ............................ 14-4 Ceiling Mount Kit CM100 ..............................14-5 Projector Transport Handle ..............................14-6 Projector Frame for Dual or Triple Configurations ........................ 14-6 Multifunctional flight case ..............................
Page 7 Safety Instructions WARNINGS AVERTISSEMENTS Safety instructions Prescriptions de securite On safety Securite On installation Installation On servicing Entretien et reparation On cleaning Nettoyage On repacking R e-emballage On illumination E clairage 5975288A BARCOGRAPHICS 8200LC 150597...
Page 8 Lire ce manuel complètement avant de mettre l’appareil en fonction- nement et le conserver pour consultation ultérieure. L’installation et les réglages préliminaires devraient être faits par du personnel qualifié BARCO ou par des agents autorisés du service BARCO. 5975288A BARCOGRAPHICS 8200LC 150597...
Page 9 Record these numbers in the spaces provided below. Refer international safety standards IEC950, UL 1950 and CSA C22.2 No. to them whenever you call upon your BARCO dealer regarding this 950, which are the safety standards of information technology equip- product.
Page 10 Prescription de sécurtié ATTENTION RISQUE D'ELECTRO- CUTION NE PAS OUVRIR ATTENTION : AFIN DE REDUIRE LE RISQUE DE CHOCS ELECTRIQUES, NE PAS ENLEVER LE COUVERCLE (OU LE DOS) IL N'Y A PAS DE PIECES REPARABLES PAR L'UTILISATEUR A L'INTERIEUR LE SERVICE NE PEUT ETRE EFFECTUE QUE PAR DU PERSONNEL QUALIFIÉ...
Page 11 Safety Instructions The lightning flash with an arrowhead within a The exclamation point within a triangle is in- triangle is intended to tell the user that parts tended to tell the user that important operating inside this product are risk of electrical shock and/or servicing instructions are included in the to persons.
Page 12 Prescription de sécurtié Instructions pour l’utilisateur : type avec terre. Ceci est une mesure de sécurité. Si le connecteur ne s’adapte pas dans la prise, contacter votre électricien pour Si cet équipement cause des interférences de radio ou de télévision, remplacer la prise non valable.
Page 13 Safety Instructions Instructions to the user : plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-type if this equipment does cause interference to radio or television plug. reception, the user may try to correct the interference by one or more WARNING FOR THE CUSTOMERS: THIS APPARATUS MUST BE of the following measures : GROUNDED (EARTHED) via the supplied 3 conductor AC power...
Page 14 Prescription de sécurtié * Pour débrancher le cordon, le tirer par le connecteur, jamais par le * Ne pas utiliser le projecteur à proximité d’eau. cordon lui-même. * N’utiliser que le cordon d’alimentation fourni avec votre projecteur. * Si on utilise une rallonge, vérifier que le total des courants des Bien qu’ils se ressemblent, d’autres cordons d’alimentation n’ont appareils raccordés à...
Page 15 Safety Instructions * To disconnect the cord, pull it out by the plug. Never pull the cord * Use only the power cord supplied with your projector. While itself. appearing to be similar, other power cords have not been safety tested at the factory and may not be used to power the projector.
Page 16 N’utili- - Si on a répandu du liquide dans le projecteur. ser que des lampes de projection indiquées par BARCO ou un agent autorisé de BARCO ou un service. - Si l’appareil a été exposé à la pluie ou à de l’eau.
Page 17 Refer all projector service to a qualified BARCO service center. The projecor uses a metal halide projection lamp. Replacing the...
Page 18 Prescription de sécurtié Pour garantir les meilleures performance et définition, les objectifs de Eclairage projection sont spécialement traités avec un revêtement anti-reflets. En conséquence : éviter de toucher les objectifs. Pour enlever la Pour garantir la meilleure qualité possible de l’image projetée, il est poussière de l’objectif, utiliser un chiffon sec et doux.
Page 19 Safety Instructions To ensure the highest optical performance and resolution, the On illumination projection lenses are specially treated with an anti-reflective coating, therefore : avoid touching the lens. To remove dust on the lens, use In order to obtain the best quality for the projected image, it is essential a soft dry cloth.
Page 20 Prescription de sécurtié 1-14 5975288A BARCOGRAPHICS 8200LC 150597...
Page 21: Unpacking & Dimensions
Unpacking & Dimensions UNPACKING DIMENSIONS BATTERY INSTALLATION ON THE RCU 5975288A BARCOGRAPHICS 8200LC 150597...
Page 22: Unpacking
Unpacking & Dimensions Unpacking To open the banding, pull on the clip as shown in the first drawing. Pull To open Take the projector out of its shipping carton and place it on a table. For transportation, the projector is mounted on a wooden board with 3 bolts. Use a 13 mm wrench to remove these bolts. When using the projector as a table mounted configuration, always mount the 3 supporting feet (see drawing below).
Page 23: Projector Dimensions
Unpacking & Dimensions Projector dimensions (units : mm) Some examples of lenses : Name lens L min L max mm(inch) mm(inch) HD(1.2:1) 1072 (42.20) 1087 (42.79) HD(2.2:1) 1043 (41.06) 1070 (42.12) HD(3.3:1) 1017 (40.04) 1072 (42.20) HD(3.9:1) 1022 (40.24) 1162 (45.75) HD(5:1) 1082 (42.60) 1202 (47.32)
Page 24: Battery Installation In The Rcu
Unpacking & Dimensions Battery installation in the RCU. A battery is delivered inside the plastic bag with the power cord. To install the battery, remove the battery cover on the backside of the remote control by pushing the indicated handle a little to the bottom of the RCU.
Page 25: Installation Guidelines
Installation Guidelines INSTALLATION GUIDELINES Environment What about ambient light? Which screen type? What image size? How big should the image be? Where to install the projector? How to install the projector? 5975288A BARCOGRAPHICS 8200LC 150597...
Page 26: Environment
Installation Guidelines Installation guidelines Careful consideration of things as image size, ambient light level, projector placement and type of screen to use are critical to the optimum use of the projection system. Max. ambient temperature : 104°F. Min. ambient temperature : 32°F. The projector will not operate if ambient temperature falls ouside this range (32°F-104°F).
Page 27: Which Screen Type
Installation Guidelines * Which screen type? There are two major categories of screens used for projection equipment. Those used for front projected images and those for rear projection applications. Screens are rated by how much light they reflect (or transmit in the case of rear projection systems) given a determined amount of light Screen width projected toward them.
Page 28: Where To Install The Projector
Installation Guidelines * Where to install the projector? Inputs and computer video format input compatibility : Some examples : Definitions of the Abbreviation on drawings B = Distance between ceiling and top of the screen or between VIDEO and S-VIDEO floor and bottom of the screen.
Page 29 Installation Guidelines Ceiling mounting of the BARCOGRAPHICS 8200LC Table mounting of the BARCOGRAPHICS 8200LC Ceiling Optical axis projection lens CD = B - A Projector Screen Screen Projector CD = B - A Optical axis projection lens SIDE VIEW Floor SIDE VIEW Screen Screen...
Page 30: How To Install A Projection Lens
The following lenses are available as an option : The installation instruction for this support is enclosed in the packet HD(0.9:1) (only for on-axis) of the set. You can order these instructions also from BARCO. HD(1.2:1) (BARCO order number R5975693) HD(2.2:1)
Page 31: Installation Set Up
Installation Set Up INSTALLATION SET UP Projector configuration 5975288A BARCOGRAPHICS 8200LC 150597...
Page 32 Installation Set Up The BARCOGRAPHICS 8200LC can be installed to project images in four different configurations : front/table, front/ceiling, rear/table and rear/ceiling. Rear/Ceiling Front/Ceiling Rear/Table Front/Table 5975288A BARCOGRAPHICS 8200LC 150597...
Page 33 Installation Set Up To change the Configuration, enter the adjustment mode by pushing ADJUST or ENTER . ADJUSTMENT MODE Highlight Installation by pushing the control disk up or down and press ENTER to select. The installation menu will be displayed. Select a path from below : GUIDED RANDOM ACCESS...
Page 34 Installation Set Up 5975288A BARCOGRAPHICS 8200LC 150597...
Page 35: Location And Function Of Controls
Location and Function of Controls LOCATION AND FUNCTION OF CONTROLS Front panel terminology Local keypad Remote control 5975288A BARCOGRAPHICS 8200LC 150597...
Page 36: Front Panel Terminology
Location and Function of Controls Front panel terminology PROJECTOR MODE : Th is de vice co mplies w ith Part 1 5 o f the F CC rules. Op era tion is su bje ct to fo llo win g two co nd itions : (1 ) Th is de vice ma y not cau se ha rmful int erf eren ce DIAGNOSTICS (2 ) Th is de vice must a ccept a ny inte rf eren ce re ce ived...
Page 37: Control Panel Terminology
Location and Function of Controls Control Panel Terminology a. Local keypad Gaining access The keypad is located behind a door, screened with the name of the projector. To open the door, push once on the indicated side of the door and turn it to the front side of the projector.
Page 38 Location and Function of Controls Remote Control (RCU) Local keypad EXIT ENTER STBY PAUSE TEXT FREEZ HELP PHASE SHARPNESS STANDBY EXIT TINT ENTER COLOR TEXT PAUSE BRIGHTNESS SHARPN TINT BRIGHTN CONTRAST PHASE COLOR CONTRAST 5975288A BARCOGRAPHICS 8200LC 150597...
Page 39 Location and Function of Controls Terminology TEXT : when adjusting one of the image, e.g. controls during a meeting, the displayed bar scale can be removed by pressing 'TEXT' key first. To re-display the bar scale on Back light key : when activated, all keys will be lighted up the screen, press 'TEXT' key again.
Page 40 Location and Function of Controls 5975288A BARCOGRAPHICS 8200LC 150597...
Page 41: Power Connection
Power Connection POWER CONNECTION 5975288A BARCOGRAPHICS 8200LC 150597...
Page 42: Fuses
Power Connection Power (mains) cord connection Use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector at the front of the projector. The power input is auto-ranging from 100 to 240 VAC. This projector may be connected to an IT-power system.
Page 43 Power Connection When switching on with the power switch, the projector starts in the stand by mode. The projector mode indication lamp is red. To start image projection : a. press the 'Stand by' button on the local keypad or on the remote PROJECTOR MODE : GREEN - OPERATION control.
Page 44: Switching To Stand-By
(normal power mode). Do not use it longer. Replace always with a Operating the lamp longer than 1000 hours may damage same type of lamp. Call a BARCO authorized service technician for the projector. Please replace the lamp lamp replacement.
Page 45: Input Module Connections
Connections INPUT MODULE CONNECTIONS Module insertion into the projector. Video/S-Video input module RGB analog input module Component input module RGB3S/RG3sB input module Peripheral equipment connection Connecting a computer Connecting a RCVDS05 Connecting a VS05 Connecting an IR Remote Receiver 800 5975288A BARCOGRAPHICS 8200LC 150597...
Page 46: Input Connections
Connections Input connections. The projector has modular input facilities. The input slots can be filled up with the following modules : DIAG NO STICS CO DE IR- RECEIVER IR-ACKNO WLEDGED Video, S-video input 1 00 - 23 0 V RS232 OUT 9 - 4 A 60 - 50 H z IR- RECEIVED...
Page 47: Video/S-Video Input Module
Connections Video/S-video input module To the Video input : Composite video signals from a VCR, OFF air signal decoder, etc... 1 x BNC 1.0Vpp ± 3 dB VIDEO/S-VIDEO INPUT To the S-Video input : Audio input not S-Video input available Video input Separate Y-luma/C-chroma signals for higher quality playback of Super VHS-signals.
Page 48 Connections Push the Control disk up or down to highlight Installation and press ENTER to display the Installation menu. ADJUSTMENT MODE EXIT returns to operational mode. Select a path from below : GUIDED RANDOM ACCESS INSTALLATION SERVICE Use the control disk to select Input Slots by pushing it up or down and Source 01 Select with press ENTER .
Page 49 Connections Straps on module level. Floating or non-floating input. Video input : J11 : strap "yes" : non floating strap "no" : floating S-Video input : J12 : strap "yes" : non floating strap "no" : floating J13 : strap "yes" : non floating strap "no" : floating Factory preset : strap on, input non floating.
Page 50: Rgb Analog Input Module
Connections RGB analog input module. RGBS/RGsB analog : 5 x BNC Red : 0.7 Vpp ± 3 dB RGB analog input terminals with separate Horizontal and Vertical Blue : 0.7 Vpp ± 3 dB sync inputs(RGB-HV), with Composite sync input(RGB-S) or with Green : 0.7 Vpp ±...
Page 51 Connections RGB input selection : Sync selection Separate sync Sync on green Key in the corresponding slot number on the RCU or the local keypad. Straps on module level : Floating or non-floating input. Red : J3 : strap "yes" : non floating strap "no"...
Page 52 Connections Push the control disk up or down to select Installation and press ENTER . ADJUSTMENT MODE Select a path from below : GUIDED RANDOM ACCESS INSTALLATION SERVICE Use the control disk to select Input Slots by pushing up or down and Source 01 Select with press ENTER .
Page 53: Component Input Module
Connections Component input module. Connect your component signals (Y-luma, R-Y and B-Y), e.g. a professional VCR to the Component input module. Component video : 4 x BNC R-Y : 0.7 Vpp ± 3 dB B-Y : 0.7 Vpp ± 3 dB 0.7 Vpp ±...
Page 54 Connections Component input selection : Floating or non floating input Non-Floating Key in the corresponding slot number on the RCU or the local keypad. Floating Indication on the input slot menu : Component Video-SS = Component video with separate sync Component Video-SOY = Component video with sync on Y Component Video-3LSS = Component video with 3 level separate sync...
Page 55: Rgb3S/Rg3Sb Input Module
Connections RGB3S/RG3sB input module. Connect your RGB signals with Tri-level sync, e.g. a professional H / C VCR to the RGB 3 level sync input module. RGB3S/RG3sB analog : 5 x BNC Red :0.7 Vpp ± 3 dB Blue : 0.7 Vpp ± 3 dB Green : 0.7 Vpp ±...
Page 56 Connections Straps on module level : Sync selection Separate sync Sync on green Floating or non-floating input. Red : J3 : strap "yes" : non floating strap "no" : floating Green : J4 : strap "yes" : non floating strap "no" : floating Blue : J5 : strap "yes"...
Page 57: Connecting A Computer, E.g. Ibm Pc (Or Compatible), Apple Macintosh To The Rs 232 Input Of The Projector
Connections Connecting a computer, e.g. IBM PC (or compatible), Apple Macintosh to the RS 232 input of the projector. This device co mplies w ith Part 15 of the FCC rul es. Oper ation is subject to fol lowing two co nditio ns : (1) T his device may not cause harmf ul interfe rence DIAGNOSTICS (2) This device must accept any in terfere nce rece ived...
Page 58: Connecting A Rcvds 05 To The Projector
In addition, the audio signal proper to the source, can be switched to an audio amplifier. Order number : R9827890 For more information about the use of the VS05, consult the VS05 Control room Projection room owner's manual, BARCO order number : R5975245. 7-14 5975288A BARCOGRAPHICS 8200LC 150597...
Page 59: Controlling
Controlling CONTROLLING How to use the RCU. Projector address How to display a projector address. How to program an address into the RCU. Picture controls with direct access. 5975288A BARCOGRAPHICS 8200LC 150597...
Page 60: How To Use The Rcu
Controlling The BARCOGRAPHICS 8200LC can be controlled with b) RCU used in a hardwired configuration. a. the RCU b. the hardwired RCU (cable is not included) c. the local keypad. Controlling the projector with the RCU and the hardwired RCU is equal.
Page 61: Projector Address
Controlling c) Point the front of the RCU directly at one of the IR sensors of the Projector address projector. a. Software set up of the projector address. IR sensor IR sensor Ceiling See 'Change projector address' in chapter 'Service mode'. Every projector requires an individual address between 0 and 255 which can be set in the Service mode.
Page 62: How To Display A Projector Address
Controlling How to display a projector address? Press the ADDRESS key (recessed key on the RCU) with a pencil. The projector's address will be displayed in a 'Text box'. This text box disappears after a few seconds. To continue using the RCU, it is necessary to enter the same address with the digit buttons (address between 0 and 9).
Page 63 Controlling Contrast Control Tint Control A correct 'contrast' setting is important for good image reproduction. Tint is only active for Video and S-Video when using the NTSC 4.43 Adjust the contrast to the level you prefer, according to room lighting or NTSC 3.58 system.
Page 64 Controlling 5975288A BARCOGRAPHICS 8200LC 150597...
Page 65: Start Up Of The Adjustment Mode
Start Up of the Adjustment Mode START UP OF THE ADJUSTMENT MODE 5975288 BARCOGRAPHICS 8200 110497...
Page 66: Adjustment Mode
Start Up of the Adjustment Mode Adjustment Mode All source set ups, picture tunings and geometry are made while in the 'Adjustment mode' . Press the ADJUST or ENTER key to enter the 'Adjustment mode'. ADJUSTMENT MODE Select a path from below : You are now in the 'Adjustment mode'.
Page 67 Start Up of the Adjustment Mode Some items in the Adjustment mode are password protected. While selecting such an item, the projector asks to enter your password (Password protection is only available when the password strap on the controller module is ON, see 'Change password' in chapter 'Service mode'.
Page 68 Start Up of the Adjustment Mode 5975288 BARCOGRAPHICS 8200 110497...
Page 69: Guided Adjustment Mode
Guided Adjustment Mode GUIDED ADJUSTMENT MODE 10-1 5975288A BARCOGRAPHICS 8200LC 150597...
Page 70 Guided Adjustment Mode The Guided Adjustment Mode is not active. ADJUSTMENT MODE Select a path from below : GUIDED RANDOM ACCESS INSTALLATION SERVICE Source 01 Select with then <ENTER> <EXIT> to return. 10-2 5975288A BARCOGRAPHICS 8200LC 150597...
Page 71: Random Access Adjustment Mode
Random Access Adjustment Mode RANDOM ACCESS ADJUSTMENT MODE File Service Picture Tuning Geometry 11-1 5975288A BARCOGRAPHICS 8200LC 150597...
Page 72: Starting Up The Random Access Adjustment Mode
Random Access Adjustment Mode Starting up the Random Access Adjustment Mode ADJUSTMENT MODE Push the control disk up or down to highlight 'Random Access' and then press ENTER . Select a path from below : GUIDED RANDOM ACCESS INSTALLATION SERVICE Source 01 Select with then <ENTER>...
Page 73: File Service
Random Access Adjustment Mode File service File annotation : xxxxxxxx.xxx x xxxxXxxxxi Before using a new source, a correct file has to be installed. The projector's memory contains a list of files corresponding to the most i or blanc : i = interlaced, blanc = not used sources.
Page 74: Load File
Random Access Adjustment Mode Load file Push the control disk up or down to select LOAD and press ENTER to display the Load menu. FILE SERVICE The Load menu displays the corresponding files depending on the LOAD installed filter. EDIT RENAME COPY This filter can be "Fit"...
Page 75: Edit File
Random Access Adjustment Mode Edit file The Edit file menu makes it possible to change the settings of the file according to the actual settings of the connected source. Consult the FILE SERVICE source specification before entering the data. To start up the EDIT menu, push the control disk up or down to select LOAD EDIT EDIT in the FILE menu and press ENTER .
Page 76 Random Access Adjustment Mode up or down to scroll to desired digit. When finished press ENTER to of the projected image. This value is normally given in the specifica- confirm. tion of the source. If not, adjust until full image height is displayed (no c.
Page 77 Random Access Adjustment Mode Options Source number : The source number of a non-active source can be changed to any other source number. This makes it possible to EDIT FILE OPTIONS Source number create a file for future source numbers. Clamp position [leading] Clamp delay...
Page 78 Random Access Adjustment Mode Vertical refresh [sync/async] : The way of updating the image information on the LCD panels. * For sources with a vertical frequency up to 60 Hz : the vertical refresh rate is the same as the vertical frequency of the incoming source. This is a necessity to project moving images without 'motion artifacts'.
Page 79: Rename
Random Access Adjustment Mode Rename FILE SERVICE To change the name of a selected file. LOAD Use the control disk to select RENAME and press ENTER . The EDIT Rename selection menu will be displayed. RENAME COPY DELETE OPTIONS Use the control disk to select a file name and press ENTER to select. Select with then <ENTER>...
Page 80: Copy
Random Access Adjustment Mode Copy FILE SERVICE To copy a selected file into a new file. LOAD Use the control disk to select COPY and press ENTER . The Copy EDIT RENAME selection menu will be displayed. COPY DELETE Use the control disk to select a file name and press ENTER to select. OPTIONS The Copy menu will be displayed with the selected file name already Select with...
Page 81: Delete
Random Access Adjustment Mode Delete FILE SERVICE To delete a selected file out of the list of files. LOAD Use the control disk to select DELETE and press ENTER . The delete EDIT RENAME selection menu will be displayed. COPY DELETE OPTIONS Push the control disk up or down to select a file and press ENTER .
Page 82: File Options
Random Access Adjustment Mode File Options FILE SERVICE Use the control disk to select OPTIONS and press ENTER . The LOAD option selection menu will be displayed. EDIT RENAME COPY DELETE OPTIONS Select with Press ENTER to toggle between [name] and [index] then <ENTER>...
Page 83: Sync Slow/Fast
Random Access Adjustment Mode Sync slow/fast PICTURE TUNING Highlight sync by pushing the control disk up or down and press ENTER to toggle SYNC [SLOW] between SLOW and FAST. STILL VIDEO [ON] COLOR BALANCE GAMMA Note : Sync is normally used in the SLOW position. The FAST position is used to compensate for unsteady sync pulses from older video playback equipment.
Page 84: Color Balance
Random Access Adjustment Mode Color Balance PICTURE TUNING Highlight Color Balance by pushing the control disk up or down and SYNC : SLOW press ENTER to select the color balance selection menu. STILL VIDEO : ON COLOR BALANCE GAMMA The next choices are possible : Fixed color balance : Select with COLOR BALANCE...
Page 85: Gamma
Random Access Adjustment Mode Gamma PICTURE TUNING With the gamma correction adjustment, it is possible to bring the SYNC [SLOW] details in dark image parts more to the front (lower image values) or STILL VIDEO [ON] COLOR BALANCE to reduce the importance of these details (higher gamma values). GAMMA To change the gamma value, highlight Gamma by pushing the control disk up or down and press ENTER .
Page 86: Geometry
Random Access Adjustment Mode Geometry RANDOM ACCESS ADJUSTMENT MODE Highlight Geometry by pushing the control disk up or down and press FILE SERVICE ENTER to select the geometry selection menu. PICTURE TUNING The following adjustment are possible : GEOMETRY - horizontal and vertical image shift. - horizontal and vertical image size - side keystone (only necessary if the projector is mounted under Select with...
Page 87: Size
Random Access Adjustment Mode Size GEOMETRY Highlight Size by pushing the control disk up or down and press SHIFT ENTER to select. SIZE SIDE KEYSTONE BLANKING OPTIONS Select with then <ENTER> <EXIT> to return. The size can be adjusted in a vertical or horizontal way. Fixed sides When adjusting the vertical size, Horizontal size...
Page 88: Side Keystone
Random Access Adjustment Mode Side keystone GEOMETRY Highlight Side Keystone by pushing the control disk up or down and SHIFT press ENTER to select. SIZE SIDE KEYSTONE BLANKING The side keystone adjustment is used to align the image if the OPTIONS projector is mounted as a non standard projection angle.
Page 89: Blanking
Random Access Adjustment Mode Blanking GEOMETRY Highlight Blanking by pushing the control disk up or down and press SHIFT ENTER to select. SIZE SIDE KEYSTONE BLANKING OPTIONS Blanking adjustments affect only the edges of the projected image Select with then <ENTER> and are used to frame the projected image on to the screen and to <EXIT>...
Page 90 Random Access Adjustment Mode Adjustment of the blanking on the of the image BLANKING Adjustment of the blanking on the bottom of the image BOTTOM LEFT Correct by pushing the control disk up or down RIGHT Select with then <ENTER> <EXIT>...
Page 91: Options
Random Access Adjustment Mode Options GEOMETRY Highlight Options by pushing the control disk up or down and press SHIFT ENTER. The Geometry Options menu will be displayed. SIZE The next question will be asked by the projector : SIDE KEYSTONE BLANKING 'Use the same side keystone correction for all files ? [YES] or [NO].
Page 92 Random Access Adjustment Mode 11-22 5975288A BARCOGRAPHICS 8200LC 150597...
Page 93: Installation
Installation INSTALLATION Convergence Configuration Internal Patterns 12-1 5975288A BARCOGRAPHICS 8200LC 150597...
Page 94: Starting Up The Installation Mode
Installation Starting up the Installation Mode ADJUSTMENT MODE Push the control disk up or down to highlight Installation and then Select a path from below : press ENTER . GUIDED RANDOM ACCESS INSTALLATION SERVICE ENTER continues to the Installation mode selection menu. Source 01 EXIT returns to operational mode.
Page 95: Input Slots
Installation Input Slots INSTALLATION Highlight Input Slots by pushing the control disk up or down and press ENTER . INPUT SLOTS CONVERGENCE The internal system will scan the input slots and displays the result CONFIGURATION INTERNAL PATTERNS in the Input Slots menu. Source indication Select with...
Page 96: Convergence
Installation Convergence INSTALLATION Highlight "Convergence" by pushing the control disk up or down and INPUT SLOTS CONVERGENCE press ENTER to display the convergence selection menu. CONFIGURATION Every LCD panel has 6 adjustment screws. By turning these screws INTERNAL PATTERNS you change the relative position of the panels and converge the image.
Page 97 Installation To adjust the convergence, there are test patterns provided in the convergence menu. CONVERGENCE GREEN Use the control disk to hightlight Convergence and press ENTER to BLUE ON GREEN display the Convergence menu. RED ON GREEN HATCH Start with the Green test pattern and continue with the Red on green and finish with the Blue on green.
Page 98 Installation The three alignments influence each other, therefore repeat if neces- sary the above three steps (b,c and d). When the green pattern is correctly focused, press EXIT to return to the Convergence menu. Red on green convergence. CONVERGENCE Use the control disk to hightlight Red on green and press ENTER to display the Red on green test pattern.
Page 99 Installation If both lines are correctly converged, continue with screw 4. Adjust screw 4 until line 4 is correctly converged. It is possible that line 2 and 3 have to be reconverged. If so, repeat procedure for screw 2 and 3 (step b and c) If line 2, 3 and 4 are converged, continue with line 1 (screw 1).
Page 100 Installation Blue on green convergence. CONVERGENCE Use the control disk to highlight Blue on green and press ENTER to GREEN display the Blue on green test pattern. BLUE ON GREEN RED ON GREEN HATCH Repeat the same procedure as for Red on green lines but read blue when red is indicated.
Page 101: Configuration
Installation Configuration INSTALLATION Highlight "Configuration" by pushing the control disk up or down and INPUT SLOTS press ENTER to select. CONVERGENCE CONFIGURATION INTERNAL PATTERNS For more information, see Projector configuration in chapter Installa- tion Set Up. Select with then <ENTER> <EXIT>...
Page 102 Installation 12-10 5975288A BARCOGRAPHICS 8200LC 150597...
Page 103: Service Mode
Service Mode SERVICE MODE Identification Change Password Change Language Change Projector Address Change Baudrate PC Reset Lamp Run Time Lamp Run Time History Panel Adjustments Preset Color Balance I²C Diagnosis 1 3 - 1 5975288A BARCOGRAPHICS 8200LC 150597...
Page 104: Starting Up The Service Mode
Service Mode Starting up the Service Mode ADJUSTMENT MODE Push the control disk up or down to highlight Service and then press Select a path from below : ENTER . GUIDED RANDOM ACCESS Some items in the Service mode are password protected (when the INSTALLATION SERVICE password function is active).
Page 105 Service Mode SERVICE BARCO CHANGE PASSWORD CHANGE LANGUAGE GRAPHICS 8200 IDENTIFICATION Enter new password ENGLISH CHANGE PASSWORD Proj. address : 001 0000 CHANGE LANGUAGE Soft. version : 3.0 CHANGE PROJ. ADDRESS Config : front/ CHANGE BAUDRATE PC ceiling RESET LAMP RUNTIME...
Page 106 Service Mode SERVICE PANEL ADJUSTMENT PRESET INPUT BALANCE RED COARSE IDENTIFICATION WHITE BALANCE CHANGE PASSWORD FIELD FLICKER CHANGE LANGUAGE BLACK LEVEL TOP CHANGE PROJ. ADDRESS BLACK LEVEL BOTTOM CHANGE BAUDRATE PC GAIN TOP RESET LAMP RUNTIME GAIN BOTTOM Select with <ENTER> <EXIT>...
Page 107: Identification
Service Mode Identification To display the Identification sreen, push the control disk up or down to highlight SERVICE Identification and press ENTER to display the Identification screen. IDENTIFICATION CHANGE PASSWORD The Identification screen gives an overview of : CHANGE LANGUAGE CHANGE PROJ.
Page 108 Service Mode - Baud rate : transfer speed for communication with a IBM PC (or - Projector Run Time : gives the total run time since the first start up. compatible) or MAC. The baud rate of the projector must be the same All projectors leave the factory with a run time of approximately 24 as the baud rate of the connected computer.
Page 109: Change Password
Service Mode Change Password Loosen the locking This item is password protected when the password strap is installed. screws. How to enable or disable the password function ? The password function is enabled when the password strap on the This device complies with Part 15 of the FCC rules. Operation is subject to following two conditions : (1) T his device may not c ause harmf u l interference DI AGNOSTICS...
Page 110 Service Mode When the strap is on leg 2-3 or no strap is mounted, the password function is enabled, when the strap is on leg 1-2, the password function is disabled. Password enabled Password disabled strap on leg 2-3 strap on leg 1-2 1 3 - 8 5975288A BARCOGRAPHICS 8200LC 150597...
Page 111: How To Change The Password
Service Mode How to change the password ? SERVICE IDENTIFICATION Highlight Change password by pushing the control disk up or down CHANGE PASSWORD and press ENTER to display the Change Password menu. CHANGE LANGUAGE CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUNTIME LAMP RUNTINE HISTORY ENTER displays the Change Password menu...
Page 112: Change Projector Address
Service Mode Change Projector Address SERVICE IDENTIFICATION Every projector requires an individual address between 0 and 255. CHANGE PASSWORD CHANGE LANGUAGE This address can be software installed. CHANGE PROJ. ADDRESS To change that address, push the control disk up or down to highlight CHANGE BAUDRATE PC RESET LAMP RUNTIME Change Proj.
Page 113: Reset Lamp Runtime
Service Mode The following baud rates are available : - 9600 CHANGE BAUDRATE PC - 4800 9600 - 2400 4800 2400 - 1200 1200 - 600 - 300 - 150 Select with - 75 <ENTER> to accept The actual baud rate will be highlighted. To change the baud rate, <EXIT>...
Page 114: Lamp Run Time History
Service Mode Lamp Run Time History To get an overview of the different lamp run times, highlight Lamp SERVICE Run Time History by pushing the control disk up or down and press IDENTIFICATION ENTER . CHANGE PASSWORD CHANGE LANGUAGE A listing with the lamp serial number and the corresponding run time CHANGE PROJ.
Page 115: Panel Adjustments
Service Mode Panel Adjustments SERVICE PANEL ADJUSTMENTS Changing these settings may seriously affect the performance PRESET INPUT BALANCE of the projector. 60Hz TRACKING I2C DIAGNOSIS All panel adjustments are factory adjusted. If not really necessary, do MORE... not touch one of these adjustments. They are useful when a new panel is installed.
Page 116: Preset Input Balance
Service Mode Preset Input Balance SERVICE PANEL ADJUSTMENTS Highlight White Balance by pushing the control disk up or down and PRESET INPUT BALANCE press ENTER to select. 60Hz TRACKING I2C DIAGNOSIS With the white balance adjustment, the gain of the red and blue MORE...
Page 117: 60 Hz Tracking
Service Mode 60 Hz Tracking 60 Hz tracking is used to adjust the 60 Hz by sychronious signals SERVICE Highlight 60 Hz Tracking by pushing the control disk up or down and PANEL ADJUSTMENTS PRESET INPUT BALANCE press ENTER. 60Hz TRACKING I2C DIAGNOSIS When 60 Hz Tracking is selected in the Service Mode selection MORE...
Page 118: I2C Diagnosis
Service Mode I2C diagnosis. Give an overview of the correct working of the I²C controlled IC's. SERVICE Highlight I2C diagnosis by pushing the control disk up or down and IDENTIFICATION press ENTER to display the overview. CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ.
Page 119: Optional Equipment
Optional Equipment OPTIONAL EQUIPMENT IR remote receiver Hardwired RCU RCVDS05 VS05 MAGIK interface Adapter and communication cables Ceiling mount kit CM100 Transport handle Frame for dual or triple projection Multifunctional flightcase Mechanical shutter Adjustable lensholder 1 4 - 1 5975288A BARCOGRAPHICS 8200LC 150597...
Page 120: Ir Receiver 800
Optional Equipment IR Receiver 800 Communication cable IR Remote Receiver 800 This infra red receiver unit makes it possible to control the BARCOGRAPHICS 8200 from another room. BARCOGRAPHICS 8100 Screen There is a communication line with cable between the IR receiver and the projector or the RCVDS. The control information from the RCU can now be sent to this IR receiver.
Page 121: Rcvds 05
BARCO's digitally controlled large screen projectors. It offers the possibility to connect and switch up to 5 different Video sources, 3 different S-Video sources and 1 RGB Analog source to a BARCO projector. In addition, the audio signal proper to the source, can be switched to an audio amplifier.
Page 122: Magik Interface
Optional Equipment MAGIK Interface Multifuctional Analog Graphics Interface Kit. BARCO's MAGIK interface allows the user to connect a presentation device such as a projector or a professional monitor to any computer with analog video signal with or without maintaining the connection with its own display.
Page 123: Ceiling Mount Kit Cm100
Optional Equipment number R9827640; and 30 m (100ft), order number R9827570 b. Din Mini8-D9 adapter cable. - To connect a Macintosh computer to the BARCOGRAPHICS 8200LC. (only if the optional RS232 port is installed.) Available length : 1 m, order number R9827640. c.
Page 124: Projector Transport Handle
Optional Equipment Projector Transport Handle 0.72 m 1.15 m Order number : R9829170 Projector Frame for Dual or Triple Configurations The frame is designed for use in table as well as ceiling mount configurations. The projector can be easily locked in the solid black frame via three bolts.
Page 125: Multifunctional Flight Case
Optional Equipment Multifunctional flight case BARCO's multifunctional flight case is a special designed flight case for temporary installations of a BARCOGRAPHICS 8200 projector. Due to the advanced mechanical design of the flight case and the built-in mirror, it is possible to install the projector in a horizontal as well as in a vertical position - in ceiling mount or table configuration - without removing the projector out of the flight case.
Page 126: Mechanical Shutter
- Reaction time less than 0.5 seconds. Order number : R9829270 Adjustable lensholder With BARCO's special adjustable lensholder, it is possible to shift the - Makes it possible to project a geometric non-distored picture from displayed picture of the BARCOGRAPHICS 8200LC projector up or a non-standard projection position.
Page 127 Appendix A : Standard Source Set Up Files Standard source set up files. Standard preprogrammed set up files NAME RESOLUTION FVERT FHOR FPIX PTOT PACT LTOT LACT Name : name of file, contains the settings 640 X 200 59,924 15,700 14,318 912 Resolution : image resolution, when fol- lowed by ...I means interlaced.
Page 128 Appendix A : Standard Source Set Up Files NAME RESOLUTION FVERT FHOR FPIX PTOT PACT LTOT LACT VGA75ISO 640 X 480 75,000 39,375 31,500 800 MAC_2 640 X 480 66,667 35,000 30,240 864 MAC_LC 640 X 480 66,619 34,975 31,338 896 MUSE 960 X 518I 30,000 33,750 37,125 1100...
Page 129 Appendix A : Standard Source Set Up Files NAME RESOLUTION FVERT FHOR FPIX PTOT PACT LTOT LACT INTER_GR 1184 X 886 67,170 61,796 92,941 1504 1184 EWS_50 280 X 1024 50,000 52,350 87,948 1680 1280 1047 1024 EWS_60 280 X 1024 60,000 63,900 107,352 1680 1280 1064...
Page 130: Appendix A : Standard Source Set Up Files
Appendix A : Standard Source Set Up Files NAME RESOLUTION FVERT FHOR FPIX PTOT PACT LTOT LACT PAM800 1120 X 375I 89,872 36,443 50,000 1372 1120 FMTO_2 640 X 400 55,370 24,370 21,060 864 640 X 400I 84,700 36,440 28,570 784 SUNXGA60 1024 X 768 59,984 48,287 64,125 1328 1024...
Page 131: Appendix B : Battery Replacement In The Rcu
Appendix B : Battery Replacement in the RCU Battery replacement in the RCU. Remove the battery cover on he backside of the remote control by pushing the indicated handle a little to the bottom of the RCU. Lift up the top side of the cover at the same time. (fig.
Page 132 Appendix B : Battery Replacement in the RCU 5975288A BARCOGRAPHICS 8200LC 150597...
Page 133: Appendix C : Focusing The Lens
Appendix C : Focusing the Lens Focusing the lens Loosen the fastener ring of the lens by turning counter clockwise. Focus the image by turning the lens barrel to the left or the right. Attention : Do not turn out the lens too far, otherwise it will fall out of the lens holder. When the image is focused, secure the correct position of the lens with the fastener ring by turning this ring clockwise.
Page 134 Appendix C : Focusing the Lens 5975288A BARCOGRAPHICS 8200LC 150597...
Page 135: Appendix D : Lens Cleaning Procedure
Appendix D : Lens Cleaning Procedure Lens Cleaning Procedure Cleaning procedure for the other HD lens Cleaning procedure for HD(1.5-3:1) lens and HD(3-5.3:1) lens. To minimize the possibility of damaging the optical coating or scratch- To minimize the possibility of damaging the optical coating or scratch- ing exposed lens surfaces, we have developed recommendations for ing exposed lens surface, we have developed recommendations for cleaning lenses.
Page 136 Appendix D : Lens Cleaning Procedure the lens. Wipe at a speed that is equal to the evaporation rate. This is very important to prevent streaking and spotting. Start your wiping at one side of the lens and, with successive wipes, move to the other side.
Page 137 Appendix E : Source Number 90 - 99 Source numbers 90 - 99 These source numbers do not correspond to physical inputs. They can only be used when the projector is equipped with a RCVDS 05 or VS05. An additional adjustment file can be created for these source numbers.
Page 138 Appendix E : Source Number 90 - 99 5975288A BARCOGRAPHICS 8200LC 150597...
Page 139: Appendix F : Lenses
Appendix F : Lenses Lenses This APPENDIX gives an overview of the tables and formulas for the available lenses for the BARCOGRAPHICS 8200LC. The next lenses are available : Name length lens diam. lens weight order number mm (inch) mm (inch) kg (lbs) HD(1.2:1) 253 (9.96)
Page 140 Appendix F : Lenses Lens formulas to calculate the projector distance. HD(1.2:1) Metric PD=1.264 x SW + 0.126 + (0.018/SW) Inch PD= 1.264 x SW + 4.961 + (27.90/SW) HD(2.2:1) Metric PD=2.0566 x SW + 0.16 + (0.029/SW) Inch PD=2.0566 x SW + 6.299 + (44.95/SW) HD(3.3:1) Metric PD=3.33 x SW + 0.386 + (0.046/SW) Inch...
Page 141 Insert card RCU INPUT SOURCES INPUT SOURCES PROJECTOR PROJECTOR INPUT SOURCES INPUT SOURCES RCVDS RCVDS 5975288A BARCOGRAPHICS 8200LC 150597...

This manual is also suitable for:

R9001339

Barco R9001338 Owner's Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Barco R9001338

Summary of Contents for Barco R9001338

This manual is also suitable for:

Table of Contents