Canon iR2422 series Service Manual page 277

[Detailed Discussions of BitSW14-6]
Select whether to enable or disable noise reduction mode during terminal temperature rises. Select "On" to start slowdown at a temperature lower than normal when
printing on smaller-sized paper than B4. Slowdown control thus enabled prevents the thermal degradation of the fusing film grease, assuring smooth sliding among
the fixing film, heater and film guide to cut squeaks.
[BitSwitch 15]
Setting item.
SW15-0
SW15-1
SW15-2
[Detailed Discussions of BitSW15-0]
Select whether to inhibit automatic delivery tray replacement while running jobs with an inner two-way tray mounted in position. Select "On" to inhibit automatic
tray replacement.
[Detailed Discussions of BitSW15-1]
Select whether to halt stapling job when a finisher installed has run out of staples. Select "On" to halt staple jobs when the finisher has run out of staples.
[Detailed Discussions of BitSW15-2]
Select whether to display a tray full message when the maximum allowable stapled document count is exceeded with a finisher installed. Select "On" not to display
the message.
[Fuser temp.-Bypass]
Lower the fixing temperature from the target temperature setting to reduce the chances of fixing offsets and curled or stuck delivered sheets occurring with paper
picked from a manual feed tray.
[Fuser temp.-Tray1]
Lower the fixing temperature from the target temperature setting to reduce the chances of fixing offsets and curled or stuck delivered sheets occurring with paper
picked from cassette 1.
[Fuser temp.-Tray2]
Lower the fixing temperature from the target temperature setting to reduce the chances of fixing offsets and curled or stuck delivered sheets occurring with paper
picked from cassette 2.
[Fuser temp.-Tray3]
Lower the fixing temperature from the target temperature setting to reduce the chances of fixing offsets and curled or stuck delivered sheets occurring with paper
picked from cassette 3.
[Fuser temp.-Tray4]
Lower the fixing temperature from the target temperature setting to reduce the chances of fixing offsets and curled or stuck delivered sheets occurring with paper
picked from cassette 4.
[Film Speed-Bypass]
Change the fixing film speed to reduce the chances of streaks appearing in the trailing edge of images caused by shocks from the fixing roller out of position while
picking paper from a manual feed tray.
[Film Speed-Tray]
Change the fixing film speed to reduce the chances of streaks appearing in the trailing edge of images caused by shocks from the fixing roller out of position while
picking paper from a cassette.
[Define U1 Paper Size]
[Define U2 Paper Size]
[Define U3 Paper Size]
With a special paper compatibility kit (cassette size adjuster) installed, set the cassette paper size lever to paper size groups U1 to U3 to set the paper sizes listed
below.
[Print Test-Page]
Not used.
[Print Test-Interval]
Not used.
[B4-Large/Small]
Use it to specify whether B4 paper should be counted as large-size paper.
If 'Large' is selected, B4 paper will be counted as large-size paper.
If 'Small' is selected, on the other hand, B4 paper will be counted as small-size paper.
[Waste Toner Full]
Select whether to display the waste toner full warning as a drum replacement required message or as service call displayed on the control panel. Select 'Operation
call' to display a rum replacement required message on an operation call. Select 'Service call' to display service call.
Function
Inhibit automatic delivery tray replacement while running jobs
Halt stapling job when out of staples
Inhibit tray full indication while the stapled document count is exceeded
Paper size group Setting (*default)
U1 29
31*
40
U2 24*
26
27
28
36
37
39
U3 25
30
32
34*
35
Setting value
On, Off
On, Off
On, Off
Paper name
A-LTR
G-LTR
8K
Foolscap
Officio
E-Officio
B-Officio
A-Offico
M-Officio
16K
A-Foolscap
A-LTR-R
G-LTR-R
G-LGL
Folio
16KR
Chapter 14
14-5