Table of Contents
Advertisement
MAIN OPERATION
The ____ in the Adjustable Range column indicates the preset mode.
BATTERY/P2CARD
Items/
Data Saved
Select the battery to use. Battery-
remaining detection matched to the
battery is performed when HYTRON 140,
DIONIC 90, or DIONIC 160 from Anton/
Bauer, ENDURA 10 (E-10) from IDX, or
PAG L95 from PAG is selected.
Select TYPE A, TYPE B, or TYPE C for
batteries other than those mentioned
above. At this time, set FULL (full
voltage), NEAR END (near end warning
voltage), and END (end voltage) for the
selected battery type in the [BATTERY
SETTING] (page 188).
The initial values for TYPE A are set
matching the IDX ENDURA ELITE-S, and
TYPE B is set matching the Anton/Bauer
HYTRON 140.
If BAT STAT is selected when using a
battery for which the remaining battery
level is detected as a percentage
value, the near end and end
operations are performed in
accordance with the percentage value
for the remaining battery level.
Set the percentage values of NEAR
END and END of BAT STAT in
[BATTERY SETTING] (page 188) to
match the battery that is used.
If the percentage value for the remaining
battery level cannot be detected even
though BAT STAT has been set, the
operations will be in accordance with the
setting values of TYPE A (page 188).
Check that the setting values of FULL,
NEAR END, and END of TYPE A match
the battery that is used.
– C U F –
Set the remaining capacity detection type
when a battery is connected to the DC IN
connector. Remaining capacity detection
is also performed according to the
selected battery type.
Selection of battery types is similar to the
above mentioned BATTERY SELECT
menu option. (Except for BAT STAT)
Analog voltage is displayed on the
viewfinder screen.
– C U F –
Select whether or not to set the alarm to
beep for BATT NEAR END ALARM.
– C U F –
If set to ON, the warning tone and
indication can be canceled by pulling the
MARKER SEL, MODE CHK/MENU
CANCEL switch when BATT NEAR END
ALARM is triggered.
– C U F –
Select whether or not to set the alarm to
beep for BATT END ALARM.
– C U F –
Remarks
Data Saved
– C U F –
– C U F –
– C U F –
– C U F –
– C U F –
Data Saved
– C U F –
– C U F –
Items/
Set the display of the remaining battery
level indicator bar in the display window
when a battery with this function is used.
70%: Indicate FULL at 70% capacity.
: Indicate FULL at 100% capacity.
Select whether or not to set the alarm to
beep for P2 CARD NEAR END ALARM.
Set the remaining time to indicate the P2
CARD NEAR END TIME alarm.
Select whether or not to set the alarm to
beep for P2 CARD END ALARM.
Set the length of time for one segment
( ) of the P2 card's remaining capacity
indicator bars.
3min/ : One segment represents 3
minutes.
5min/ : One segment represents 5
minutes.
BATTERY SETTING (1/2)
Items/
Enable selection under BATTERY
SELECT.
:Enable selection.
•: Disable selection.
Select auto or manual to set the NEAR
END voltage.
AUTO: Set voltage automatically.
: Set voltage manually.
When MANUAL is selected in the menu
above, set the NEAR END voltage in 0.1
:
V steps.
:
Enable selection under BATTERY
SELECT.
:Enable selection.
•: Disable selection.
Select auto or manual to set the NEAR
END voltage.
AUTO: Set voltage automatically.
: Set voltage manually.
When MANUAL is selected in the menu
above, set the NEAR END voltage in 0.1
:
V steps.
:
Menu: Menu Description Tables
Remarks
Remarks
Advertisement
Table of Contents
