Rrp8.2 Main Motor (Pl 8.1.2) - Oki B6500 Service Manual
Hide thumbs
Also See for B6500:
- Manual do utilizador (167 pages) ,
- Troubleshooting manual (162 pages) ,
- Guía del usuario (161 pages)
Table of Contents
Advertisement
RRP8.2
MAIN MOTOR (PL 8.1.2)
Removal
1)
Remove the COVER REAR 500 (PL 7.1) (RRP7.9).
2)
Remove the COVER REAR (PL 1.1) (RRP1.1).
3)
Remove the FUSER ASSEMBLY (PL 6.1) (RRP6.8).
4)
Remove the COVER LEFT (PL 1.1) (RRP1.3).
5)
Remove the COVER RIGHT (PL 1.1) (RRP1.2).
6)
Remove the COVER EXIT 500 (PL 1.1) (RRP7.1).
7)
Remove the 500 EXIT ASSEMBLY (PL 7.1) (RRP7.2).
8)
Remove the COVER TOP (PL 1.1) (RRP1.4).
9)
Remove the COVER FRONT (PL 1.1) (RRP1.5).
10) Remove the BTR ASSEMBLY (PL 6.1) (RRP6.9).
11) Remove the DUCT FRONT (PL 6.1) (RRP6.2).
12) Remove the ROS ASSEMBLY (PL 6.1) (RRP6.1).
Be careful not to drop or strike the ROS Assembly with any tools or other objects.
13) Remove the SHIELD PLATE ROS (PL 6.1) (RRP6.3).
14) Remove the GUIDE TRAY LEFT (PL 5.1) (RRP5.8).
15) Remove the MOTOR COVER (PL 8.1) (RRP8.1).
16) Remove the SHIELD PLATE LVPS (PL 9.1) (RRP8.1).
17) Disconnect the connector (P/J43) of the MAIN MOTOR from the LVPS (PL 9.1.5) and disconnect
the connector (P/J271) (Figure 1).
18) Lift up the 150 FEEDER ASSEMBLY (PL 4.1) (Figure 1).
The 150 FEEDER ASSEMBLY clicks into a notch when lifted to the half way point, push
the assembly past the notch.
19) Remove the 3 screws (gold, 6mm) securing the MAIN MOTOR to the frame (Figure 1).
20) Remove the MAIN MOTOR (Figure 1).
Replacement
1)
Install the MAIN MOTOR to the frame using the 3 screws (gold, 6mm) (Figure 1).
2)
Connect the connector (P/J43) of the MAIN MOTOR to the LVPS (PL 9.1.5) and connect the con-
nector (P/J271) (Figure 1).
3)
Install the SHIELD PLATE LVPS (PL 9.1) (RRP8.1).
4)
Install the MOTOR COVER (PL 8.1) (RRP8.1).
5)
Install the GUIDE TRAY LEFT (PL 5.1) (RRP5.8).
6)
Install the SHIELD PLATE ROS (PL 6.1) (RRP6.3).
7)
Install the ROS ASSEMBLY (PL 6.1) (RRP6.1).
Be careful not to drop or strike the ROS Assembly with any tools or other objects.
8)
Install the DUCT FRONT (PL 6.1) (RRP6.2).
9)
Install the COVER FRONT (PL 1.1) (RRP1.5).
10) Install the COVER TOP (PL 1.1) (RRP1.4).
11) Install the 500 EXIT ASSEMBLY (PL 7.1) (RRP7.2).
12) Install the COVER EXIT 500 (PL 1.1) (RRP7.1).
Chapter 3 Removal and Replacement Procedures (RRPs)
3 - 141
Advertisement
Chapters
Table of Contents
Troubleshooting
