System Call Function; Punch Through Function; Setting The Time The Backlight Stays Lit - Denon AVP-A1HDE Owner's Manual

• With some remote control units, the signals cannot be learned or the
device will not operate properly even when the signals have been
learned. In this case, use the device's own remote control unit.
• Learned buttons have priority over the preset memory. If you no
longer need the learned setting, reset the learning function (vpage
74).
NOTE
[HOME]
• cannot be learned.
[RC SETUP]
• Do not learn any remote control signals at
• The AMP , ZONE2, ZONE3, ZONE4 and SYSTEM CALL modes cannot
be learned.

System Call Function

This function lets you register a series of operations at a single
button.
For example, the amplifier can be turned on, the input source
selected, the monitor's power turned on, the source device's
power turned on and the play mode set all by pressing a single
button.
Up to 32 signals each can be registered at
3
or ).
Registering
1
[MODE SELECTOR]
Press for the device you want to
register.
2
[RC SETUP]
Press and hold in for at least 3 seconds.
The signal transmission indicator flashes twice.
3
[9] [7] [8]
Press , and , in that order.
The signal transmission indicator flashes twice and the system
call registration mode is set.
4
[SYSTEM CALL] 1 2 3
Press ( , or ) at which you want to
register the signals.
5
Press the buttons you want to register in the same
sequence as the operations you want to perform.
The signal transmission indicator lights when a button is
pressed.
Example : Press
Press
Press
b The mode can be switched by pressing
.
b Perform the registration procedure for all the buttons you want to
register.
6
Press and hold in
The signal transmission indicator flashes twice and the setting
is completed.
Calling out
1
[AMP]
Press
2
[SYSTEM CALL]
Press
[SYSTEM CALL] 1 2
( ,
were registered.
The registered signals are transmitted in the registered
sequence.
[POWER ON]
.
↓
[MODE SELECTOR] [DVD]
– .
↓
[1]
.
[MODE SELECTOR]
.
[RC SETUP]
for at least 3 seconds.
, to select "SYSTEM CALL".
1 2 3
( , or ) at which the signals

Punch Through Function

CD, DVD or VCR mode buttons can be stored at unused TV or
SAT/CBL mode buttons.
For example, when DVD mode buttons are assigned to the TV
mode, the DVD mode operations can be performed while in the
TV mode.
1
[MODE SELECTOR]
Press for the device you want to
punch through (CD, DVD or VCR).
2
[RC SETUP]
Press and hold in for at least 3 seconds.
The signal transmission indicator flashes twice.
3
[9] [8] [4]
Press , and , in that order.
The signal transmission indicator flashes twice and the punch
through setting mode is set.
4
Press the button you want to punch through (1, 2,
6, 7, 8, 9 or 3).
5
[MODE SELECTOR]
Press for the device you want to
punch through (TV or SAT/CBL).
6
[RC SETUP]
Press and hold in for at least 3 seconds.
The signal transmission indicator flashes twice and the setting
is completed.

Setting the Time the Backlight Stays Lit

1
[RC SETUP]
Press and hold in for at least 3 seconds.
The signal transmission indicator flashes twice.
2
[9] [7] [3]
Press , and , in that order.
The signal transmission indicator flashes twice and the backlight
on time setting mode is set.
3
Set the light on time.
The signal transmission indicator flashes twice.
[1]
[Settable times] : : 5 sec.
[2]
: 10 sec. (Default)
[3]
: 15 sec.
[4]
: 20 sec.
[5]
: 25 sec.