Kyocera Mita FS-C5016N - Color LED Printer Service Manual page 152

FS-C5016N
Connector Pin No.
YC5 10 +5V1
Connected 11 MPFSENS1
to the bias
12 MPFSENS2
high voltage
13 WTLEDDR
PWB
14 WTSENS
15 AIRTEMP
16 WETCK1
17 WETCK2
YC6 1 +24V3
Connected 2 MCH1DR
to the main
3 MCH2DR
high voltage
4 MCH3DR
PWB
5 MCH4DR
6 +5V1
7 HVADATD
8 HVACLKD
9 HVALATD
10 GND
YC7 1 GND
Connected 2 OPRDY*
to the
3 OPSEL2
optional
4 OPSDO
paper
5 OPSEL1
feeder/
6 OPSDI
duplexer
7 OPSEL0
8 OPSCLK
9 NC
10 OP5V
11 GND
12 OP24V
YC8 1 +3.3V1
Connected 2 +3.3V1
to the main
3 +2.5V1
controller
4 +2.5V1
PWB
5 GND
6 LVDSN15
7 LVDSN14
8 LVDSN13
9 LVDSN12
10 LVDSN11
11 LVDSN10
12 LVDSN9
13 LVDSN8
14 LVDSN7
15 LVDSN6
16 LVDSN5
17 LVDSN4
18 LVDSN3
19 LVDSN2
20 LVDSN1
21 LVDSN0
22 RD
23 GND
24 SCLKIN
25 SYSRES*
26 SIOUT
27 GND
28 GND
2-3-8
Signal I/O Voltage
O 5 V DC
I 0/5 V DC
I 0/5 V DC
O 0/5 V DC (pulse)
I 0/5 V DC (pulse)
I Analog
O 0/5 V DC (pulse)
I Analog
I 24 V DC
O 0/24 V DC
O 0/24 V DC
O 0/24 V DC
O 0/24 V DC
O 5 V DC
O 0/5 V DC (pulse)
O 0/5 V DC (pulse)
O 0/5 V DC (pulse)
- -
- -
I 0/5 V DC
O 0/5 V DC
O 0/5 V DC (pulse)
O 0/5 V DC
I 0/5 V DC (pulse)
O 0/5 V DC
O 0/5 V DC (pulse)
- -
O 5 V DC
- -
O 24 V DC
I 3.3 V DC
I 3.3 V DC
O 3.3 V DC
O 3.3 V DC
- -
I Analog
I Analog
I Analog
I Analog
I Analog
I Analog
I Analog
I Analog
I Analog
I Analog
I Analog
I Analog
I Analog
I Analog
I Analog
I Analog
I 0/5 V DC
- -
I 0/5 V DC (pulse)
O 0/5 V DCC
O 0/5 V DC (pulse)
- -
- -
Description
5 V DC power output
MP tray paper sensor: On/Off
Envelope feeder install sensor: Installed/Not installed
Waste toner full sensor (emitter) drive output
Waste toner full sensor (receiver) input, Full at voltage
above the 2 V DC
Temperature sensor detection voltage input
Humidity sensor control signal (1 KHz)
Temperature sensor detection signal
24 V DC power input (via side cover switch)
Main charger output control signal (Magenta): On/Off
Main charger output control signal (Cyan): On/Off
Main charger output control signal (Yellow): On/Off
Main charger output control signal (Black): On/Off
5 V DC power output
Output control D/A converter serial signal
Output control D/A converter clock signal
Output control D/A converter data latch signal
Ground
Ground
Optional unit ready signal: Ready/Not ready
Optional unit select signal: (bit2)
Optional unit serial communication data output
Optional unit select signal: (bit1)
Optional unit serial communication data input
Optional unit select signal: (bit0)
Optional unit serial communication clock signal
Not connected
5 V DC power output (via fuse)
Ground
5 V DC power output (via fuse)
3.3 V DC power output
3.3 V DC power output
3.3 V DC power output
3.3 V DC power output
Ground
LED print head control video data signal (LVDS)
LED print head control video data signal (LVDS)
LED print head control video data signal (LVDS)
LED print head control video data signal (LVDS)
LED print head control video data signal (LVDS)
LED print head control video data signal (LVDS)
LED print head control video data signal (LVDS)
LED print head control video data signal (LVDS)
LED print head control video data signal (LVDS)
LED print head control video data signal (LVDS)
LED print head control video data signal (LVDS)
LED print head control video data signal (LVDS)
LED print head control video data signal (LVDS)
LED print head control video data signal (LVDS)
LED print head control video data signal (LVDS)
LED print head control video data signal (LVDS)
LED print head control signal
Ground
Serial communication synchronizing clock signal
System reset signal
Serial communication data output
Ground
Ground