Kyocera Mita Ecosys FS-1010 Installation Manual
  1. Manuals
  2. Brands
  3. Kyocera Mita Manuals
  4. Printer
  5. Ecosys FS-1010
  6. Installation manual

Kyocera Mita Ecosys FS-1010 Installation Manual

Kyocera mita ecosys page printer installation guide
Hide thumbs Also See for Ecosys FS-1010:
Table of Contents

Advertisement

Quick Links

See also: Service Manual , Operating Manual
Page Printer
Installation Guide

Advertisement

Table of Contents
loading

Related Manuals for Kyocera Mita Ecosys FS-1010

Summary of Contents for Kyocera Mita Ecosys FS-1010

  • Page 1 Page Printer Installation Guide...

  • Page 2: Table Of Contents

    MODE. The printer is factory-set to emulate the HP PCL 6. The emulation mode can be changed by following the procedures described in the Operation Guide contained as an electronic file in the Kyocera Mita Digital Library CD-ROM supplied with the printer. Notice The information in this manual is subject to change without notification.

  • Page 3: Step

    Toner Container (TK-17) Power Cord Cleaning Cloth Installation Guide (this booklet) Kyocera Mita Digital Library CD-ROM Removing Shipping Material Remove the tape on the rear side of the printer, and remove the two spacers and printed notice from the paper cassette.

  • Page 4: Step

    STEP Positioning the Printer Make sure that the place of installation meets the following requirements: Clearance Be sure to secure enough space 30 cm (11-13/16 inches) around the printer. Prolonged use without sufficient clearance 40 cm may cause heat to build up (15-3/4 25 cm (9-7/8 inches)

  • Page 5: Step

    STEP Installing the Toner Container Before you can use the printer for the first time, you must set up the printer by installing the toner container and interfacing with the computer. Open the printer top cover all the way. Confirm that the lock lever is in the release (UNLOCK) position.
  • Page 6 Carefully remove the protective seal. Install the toner container into the printer. Push firmly on the top of the toner con- tainer at the positions marked PUSH HERE.
  • Page 7 Push the lock lever to the lock (LOCK) position. Close the top cover. To remove the toner container Pull the lock lever #1 to the release (UNLOCK) position, pull the lock lever Lock Lever #2 #2, then gently remove the toner con- tainer.

  • Page 8: Step

    STEP Connecting the Printer to the Computer There are various ways of connecting the printer to the computer, such as through the parallel interface connector, through the USB (Universal Serial Bus) interface connec- tor, through the optional serial interface board kit (IB-10E) or through the optional net- work interface board.

  • Page 9: Parallel Interface Connection

    Parallel Interface Connection Plug one end of the printer cable (not included) into the parallel interface con- nector on the rear of the printer. Clips • Use a parallel printer cable that complies with the IEEE1284 standards. • The printer will work best if it is installed near the computer.

  • Page 10: Step

    STEP STEP Connecting the Power Cord This section describes the procedure for connecting the power cable and various cautions. Notes on Power Supply • Install the printer near an AC wall outlet, preferably one that can be used for the printer alone. •...

  • Page 11: Step

    Adding Paper to the Paper Cassette and STEP MP Tray The paper cassette can accommodate A5 to Legal size paper and can hold approxi- mately 250 sheets. The Multi-Purpose tray can accommodate the various paper sizes and can hold approximately 50 sheets of paper. The following paper weights can be used with the printer.
  • Page 12 Pull the paper cassette all the way out of the printer. Adjust the position of the paper stopper Release Button located at the rear of the paper cassette. Press in the release button and slide the Paper Stopper stopper to the desired paper size. When shipped from the factory, the paper cas- sette is set to either A4 or Letter size.
  • Page 13 Make sure that the edges of the paper are aligned. Slide the paper into the paper cassette. Do not load more paper than will Load Limit fit under the load limits on the top of the paper guides. (the paper cassette will hold approx- imately 250 sheets of paper with a 80 g/m²...
  • Page 14 Multi-Purpose (MP) tray Pull the MP tray towards you until it stops. Pull out the subtray and unfold the flap. Subtray Flap Adjust the position of the paper guides on the MP tray. Standard paper sizes are attached to the MP tray. For stan- dard paper sizes, slide the guides to the position marked correspondingly.
  • Page 15 Envelopes Envelopes should be fed in the face-up position, right edge first. • Test a sample envelope on the printer and check that printing quality is satisfactory before purchasing. • To avoid trouble, we recommend that envelopes be delivered face-up using the face-up tray.

  • Page 16: Step

    STEP Using the Face-Up Output Tray Use the face-up output tray when you wish paper to be stacked with the printed side facing up (reverse order), or when you are printing on envelopes, postcards, trans- parencies, or thick paper. Pull on the face-up output tray to open Open the extension tray by pressing with your thumbs at the corners next to the hinges.

  • Page 17: Step

    STEP Printing a Status Page To test the printer, print a status page indicating factory settings. Turn on the printer’s power switch. Upon turning on the power, the printer’s 4 indicators flash in sequence until printer initialization is complete, then the indicator ( [on line]) lights steadily.

  • Page 18: Correcting A Paper Jam

    Correcting a Paper Jam If a paper jam occurs while you are printing, remove the jammed paper as described below. After you have removed the jammed paper, open and close the top cover once. Jam at the Face-down and Face-up Trays Open the face-up tray and remove the jammed paper as shown in the figure.
  • Page 19 Open the printer's front cover. Front Cover Lift the process unit together with the toner container out of the printer. Process Unit Remove the jammed paper. When pulling the paper, pull gently so as not to tear it. Torn pieces of paper are difficult to remove and may be easily over- looked, preventing recovery from the jam.

  • Page 20: Safety Information

    Caution to user Any modification without prior permission may cause harmful interference. If any modification/change is introduced to this equipment without prior permission, Kyocera Mita as the manufacturer cannot guarantee compliance with FCC rules. To use equipment which does not comply with FCC rules is prohibited. The printer may be optionally installed with the following...

  • Page 21: Cdrh Regulations

    DANGER: INVISIBLE LASER RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE TO BEAM. CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Caution labels Label inside the printer (Laser radiation warning) (European/Asian/Pacific countries) (U.S.A./Canada) Label on the printer's rear panel...

  • Page 22: Important Safeguards

    IMPORTANT SAFEGUARDS 1. Read all of these instructions and save these instructions for later use. 2. Unplug this product from the wall outlet before cleaning. 3. Do not use this product near water. 4. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product.
  • Page 23 FS-1010 (as tested with the enhancement optional unit: PF-17 and IB-21E) Description of device: The model FS-1010 is a 14-ppm, A4 size plain paper supporting page printer, utilizing laser, dry toner, etc. The printer can be equipped with the optional paper feeder model PF-17.
  • Page 24 Declaration of Conformity (U.S.A.) Model Number: Laser Printer FS-1010 (as tested with enhancement optional units: PF-17, IB-21E.) Trade Name: Kyocera Responsible Party: Kyocera Mita America Inc. Address: 225 Sand Road PO Box 40008 Fairfield, New Jersey 07004-0008, U.S.A. Telephone number:...
  • Page 25 ® NERGY As an E Partner, Kyocera Mita Corporation has determined NERGY that this product meets the E guidelines for energy effi- NERGY ciency. The basic objective of the E Program is to reduce environ- NERGY mental pollution by encouraging the manufacture and sale of equip- ment that uses energy more efficiently.
  • Page 26 (CF) that are best suited for use with this printer. Network Interface Cards See your Kyocera Mita dealer for purchasing information of the network interface cards that is best suited for use with this printer. Use only the network interface cards operating from DC 3.3V.
  • Page 27 U.S. registered mark. All other brand and product names are registered NERGY trademarks or trademarks of their respective companies. This Kyocera Mita page printer uses PeerlessPrintXL to provide the HP LaserJet compatible PCL 6 language emulation. PeerlessPrintXL is a trademark of The Peerless Group, Redondo Beach, CA 90278, U.S.A.
  • Page 28 3. Limitation of Remedies IBM's entire liability under this license is the following; 1) For any claim (including fundamental breach), in any form, related in any way to this license, IBM's liability will be for actual damages only and will be limited to the greater of: a) the equivalent of U.S.$25,000 in your local currency;...
  • Page 29 This page intentionally left blank.
  • Page 30 This page intentionally left blank.
  • Page 31 This page intentionally left blank.
  • Page 32 Operating Keys and Indicators For details on operating procedures, see the FS-1010 Operation Guide contained as an elec- tronic file in the CD-ROM supplied with the printer. Number Name Function Ready indicator Indicates whether the printer is on-line or off-line.

Table of Contents