Table of Contents
Advertisement
CONTENTS
[5] Output checklist ............................................. 1-92
OTHER ADJUSTMENTS ......................................... 1-98
[1] Centering Adjustment .................................. 1-98
(C-305L only) ............................................. 1-101
[3] Paper up/down plate centering adjustment 1-101
[4] Skew Adjustment ....................................... 1-105
[5] Tray Spring Pressure Adjustment .............. 1-108
Adjustment ................................................. 1-109
[7] Pick-up Release Amount Adjustment ........ 1-112
[8] RADF Mounting Position Adjustment ........ 1-114
[9] RADF Skew Adjustment ............................ 1-115
[10] RADF Paper Skew Adjustment .................. 1-116
Guide Plate B ............................................. 1-119
Guide Plate C ............................................ 1-120
Exit Gate .................................................... 1-121
Gate ........................................................... 1-122
[16] FNS Adjusting the By-pass Gate ............... 1-123
[17] FNS Adjusting the Shift Position ................ 1-125
Paper Exit .................................................. 1-126
Solenoid ..................................................... 1-127
Lower Guide Plate ..................................... 1-128
Exit Arm ..................................................... 1-129
Upper Alignment Plates ............................. 1-129
Alignment-Plate Drive Timing Belt ............. 1-130
Lower Alignment Plates (FN-4 only) .......... 1-131
(FN-4 only) ................................................. 1-132
(Flat Stapling) ............................................ 1-132
Positioning ................................................. 1-133
Stopper (FN-4 only) ................................... 1-135
Stopper (FN-4 only) ................................... 1-137
Movement Timing Belt ............................... 1-138
Rotation Timing Belt .................................. 1-138
(FN-4 only) ................................................. 1-139
Knife Motor (FN-4 only) ............................. 1-139
[34] TU Trimming Parallelism Adjustment ........ 1-140
WHAT IS ISW ? .......................................................... 2-1
SETUP ....................................................................... 2-2
[1] ISW-compatible boards ................................. 2-2
[2] Data flow ........................................................ 2-2
[4] HELP + CHECK mode operation flow ........... 2-4
[5] Operating procedure ...................................... 2-6
[6] Preparing the copier to transfer ................... 2-10
and operational LEDs .................................. 2-11
interruption ................................................... 2-11
connector available ...................................... 2-12
[10] Kinds and quantities of update ROMs ......... 2-12
SERVICE SCHEDULE ............................................... 3-1
[1] Service Schedule ........................................... 3-1
[2]
Maintenance Items ....................................... 3-3
[3] Main Unit Periodic Inspection Items .............. 3-9
[4] RADF [EDH-2] ............................................. 3-13
[5] FNS [FN-104] ............................................... 3-14
[6] FNS [FN-4] ................................................... 3-14
[7] LCT [C-305/C-305L] .................................... 3-15
[8] Cover Inserter A ........................................... 3-15
[9] TU [TMG-1] .................................................. 3-16
[10] Replacement parts list ................................. 3-17
COPY MATERIALS .................................................. 3-20
[1] Consumables (Single unit supply) .............. 3-20
CE TOOL LIST ......................................................... 3-21
[1] Read Section/Operational Section ................ 4-1
[2] Charging Corona Wire Unit ........................... 4-1
[3] Drum Unit ....................................................... 4-2
[4] Cleaning Unit ................................................. 4-2
[5] Tray 1,2,3 ....................................................... 4-3
[6] Vertical Conveyance Section ......................... 4-3
[7] By-pass Feed Section ................................... 4-4
[8] Second Paper Feed Section .......................... 4-4
[9] ADU Unit ........................................................ 4-5
[10] Fixing Unit ...................................................... 4-6
[11] Paper Exit Section ......................................... 4-6
[12] Toner Supply Unit .......................................... 4-7
[13] Write Section ................................................. 4-7
[14] Control/Drive Unit in Rear Section ................. 4-8
Advertisement
Table of Contents
