Omron E5AK User Manual page 175

A manual revision code appears as a suffix to the catalog number on the front cover of the manual.
The following table outlines the changes made to the manual during each revision. Page numbers
refer to previous version.
Revision code
1
2
02A
02B
02C
03
Revision History
Cat. No. H083-E1-03
Date
July 1996 Original production
Page 1- -7:
April 1997
Page V:
Page 1- -6:
Page 2- -8:
Page 3- -3:
Page 3- -8:
Page 5- -8:
Page 5- -9:
Page 5- -13:
Page 5- -14:
Page 5- -15:
Page 5- -16:
Page 5- -17:
Page 5- -23:
Page 5- -28:
Page 5- -33:
Page 5- -42:
Page 5- -43:
Page 6- -3:
Page 7- -4:
Page 7- -7:
Page 7- -9:
Page 7- -10:
Page 7- -12:
Page 7- -13:
Page 8- -4:
Page A- -2:
Page A- -11:
Page A- -14:
Page A- -15:
December 2003 Page 2- -9:
Page 4- -8:
Page 4- -9:
Page 5- -3:
Page A- -8:
March 2005 Page A- -3:
March 2007 Page 5- -9:
Page 6- -6:
June 2010 Page 4- -8:
Revision code
Revised content
Modified the diagram of mode.
Page 2- -6: Modified the power specifications in "Terminal arrange-
ment".
Changed "100 to 240 VAC" to AC100- -240V
Modified the item of "Model" on the table.
Modified the diagram in "Terminal arrangement".
Changed the Power specifications in "Power supply".
Modified the diagram in "Setup".
Added "run/stop"= "run" to Setting Example.
Added "Model" and "Power specifications" to MV monitor.
Added "Model" and "Power specifications" to Valve opening monitor.
Added "Model" and "Power specifications" to Cooling coefficient.
Added "Model" and "Power specifications" to Dead band and Posi-
tion- -proportional dead band.
Added "Model" and "Power specifications" to Manual reset value and
Hysteresis.
Added "Model" and "Power specifications" to Control period.
Added "Model" and "Power specifications" to Heater current monitor
and Heater burnout.
Added "Model" and "Power specifications" to Open/close hysteresis.
Added "Model" and "Power specifications" to Control output assign-
ment.
Added "Model" and "Power specifications" to PID/ON/OFF.
Added "Model" and "Power specifications" to HBA latch.
Added "Model" and "Power specifications" to Motor Calibration.
Added "Model" and "Power specifications" to Travel Time.
Added "Model" and "Power specifications" to PV dead band.
Modified the diagram in "RS- -232C".
Modified the diagram in "Preparations".
Modified the diagram in "Preparation".
Modified the diagram in "Preparation".
Modified the diagram in "Preparation".
Modified the diagram in "Thermocouple" and "Platinum resistance
thermometer".
Modified the diagram in "Current input" and "Voltage input".
Added "Motor calibration error".
Modified "Ratings specifications".
Changed "Type Name" and "Specification" in "Base unit".
Deleted 2) of "At the time the E5AK starts operation" in "Startup
Conditions of SRT".
Deleted 2) of "At the time set point is changed".
Deleted "Imposition Completion Condition of Step Control Amount".
Modified the diagram in "PID Constant Refreshing Conditions".
Modified the diagram in "Control output".
Changed the title from "Input assignments" to "Event input assign-
ments and deleted the flowchart below.
Modified the table contents for "Event input" and added a note below
the table.
Modified the table.
Changed the unit from "%" to "%FS" for Alarm 1 hysteresis, Alarm 2
hysteresis, and Alarm 3 hysteresis.
Added information to table and accompanying notes.
Sentence starting "there is no order of priority" changed.
Example changed.
Added figure.
~
or AC/DC24V