Toshiba TOSVERT VF-P7 Instruction Manual page 212

[16] Functions for lift (2/2)
Communi
Title
cation No
0340 Heavy load torque during fixed speed in reverse direction

0341 Automatic light-load high-speed operation frequency

[17] Commercial/inverter switching function
Communi
Title Function
cation No
Output signal selection of
0354 commercial power/inverter

switching
Commercial power/inverter
 0355
switching frequency
0356 Inverter side switching waiting time Model dependent∼10.00 [s]

Commercial power side
0357

switching waiting time
Commercial power switching
 0358
frequency holding time
[18] PID control
Communi
Title Function
cation No
 0360 Signal selection of PID control 0: PID control disabled, 1: VI/II, 2: RR, 3: RX, 4: RX2
0361 Delay filter

 0362 Proportional (P) gain
0363 Integral (I) gain

 0364 PID deviation upper limit
0365 PID deviation lower limit

 0366 Differential (D) gain
[19] Speed feedback/positioning control
Communi
Title
Function
cation No
0367 Number of PG input pulses

 0368 Number of PG input phases
0369 PG disconnection detection

 0370 Electronic gear
0371 Position loop gain

 0372 Positioning completion range 1∼4000
0373 Frequency limit at position control 1∼8000 [Hz/s], 8001: disabled

※(Reference section): Refer to the inverter's individual manual.
Function Adjustment range
0∼250 [%]
30.0∼ [Hz]
Adjustment range
0: OFF, 1: Automatic switching in case of trip
2: Commercial power switching frequency setting enabled
3: Both (1+2)
0∼ [Hz]
0.37∼10.00 [s]
0.1∼10.0 [s]
Adjustment range
0∼255
0.01∼100.0
0.01∼100.0
0∼50 [%]
0∼50 [%]
0.00∼2.55
Adjustment range
1∼9999
1: Single-phase input, 2: Two-phase input
0: Disabled, 1: Enabled
100 to 4000 pulses/rotation
0.0∼100.0
Sensorless vector/vector with sensor (●valid, −:invalid)
Min. unit (panel/ Default Write during
Speed
communication) setting running
control
1 100 Enabled
●/●
0.01/0.01 80.0 Enabled
●/●
Min. unit (panel/ Default Write during
Speed
communication) setting running
control
0 Disabled
− ●/●
0.01/0.01 60.0 Enabled ●/●
0.01/0.01 See J-28 Enabled
●/●
0.01/0.01 0.62 Enabled
●/●
0.1/0.01 2.0 Enabled ●/●
Min. unit (panel/ Default Write during
Speed
communication) setting running
control
− 0 Enabled ●/●
0 Enabled
− ●/●
0.01/0.01 0.1 Enabled ●/●
0.01/0.01 0.1 Enabled
●/●
1/0.01 50 Enabled ●/●
1/0.01 50 Enabled
●/●
0.01/0.01 0 Enabled ●/●
Min. unit (panel/ Default Write during
Speed
communication) setting running
control
1/1 500 Disabled
−/●
− 2 Disabled −/●
0 Disabled
− −/●
1/1 1000 Disabled −
0.1/0.01 4.0 Enabled
−
1/1 100 Enabled −
1/1 800 Disabled
−
Vector control
V/f Reference
Torque Position
Constant section
control control
− − ● ※
− − ● ※
Vector control
V/f Reference
Torque Position
Constant section
control control
6.16
●/● − ●
●/● − ● 6.16
6.16
●/● − ●
6.16
●/● − ●
●/● − ● 6.16
Vector control
V/f Reference
Torque Position
Constant section
control control
− − ● 3.3
3.3
− − ●
− − ● 3.3
3.3
− − ●
− − ● 3.3
3.3
− − ●
− − ● 3.3
Vector control
V/f Reference
Torque Position
Constant section
control control
−/● −/● − ※
−/● −/● − ※
−/● −/● − ※
− −/● − ※
− −/● − ※
− −/● − ※
− −/● − ※