1. Kindly forward this manual to those who practically use the “External Fin Attachment” so that every user of it gets this manual without fail. 2. Please read this manual at any cost before fitting the “External Fin Attachment” to your inverter. c Toshiba Schneider Inverter Corporation 2003 All Rights Reserved.
E6581187 Contents I. Precautions on safety ..........................2 2 2 2 II. Introduction ............................... 2 2 2 2 Start reading from the following......................2 2 2 2 1.1. Type of the External Fin Attachment ....................2 1.2. Checking contents of package ......................3 Installation method..........................
1.1. Type of the External Fin Attachment The coded model name represents the type of the External Fin Attachment as explained below. 7 *5 Attachable inverter model Attachable inverter model A7,P7用 VFA7-2370P1∼2550P1 (See the table on the right 4370P1∼4750P1 hand.) VFP7-2370P∼2550P 4450P∼4900P For A7 and P7...
E6581187 1.2. Checking contents of package The External Fin Attachment comprises the following parts. Unpack and check to see if there are the following things contained. (1) Attachment ... 4 pcs (2) Manual (this booklet) of the External Fin Attachment ... 1 copy (E6581187) M a n u a (3) Set of screws to fit the attachment to the inverter ...
2.1. In case of ATFIN7*5 Attachable inverter models VFA7-2370P1, -2450P1, -2550P1, -4370P1, -4450P1, -4550P1, -4750P1 VFP7-2370P, -2450P, -2550P, -4450P, -4550P, 4750P, -4900P Step 1: Remove the inverter fitting metal (4 pcs) shown in Figure 1 from the inverter.
E6581187 2.2. In case of ATFIN7*6 Attachable inverter models VFA7-2750P1, -4110KP1, -4132KP1 VFP7-2750P, -4110KP, -4132KP, -4160KP Step 1: Remove the inverter fitting metal ① (4 pcs), ② hanging metal ② (2 pcs) and screw ③ (4 pcs) ② ① shown in Figure 3 from the inverter. ①...
E6581187 2.3. In case of ATFIN7*7 Attachable inverter models VFA7-2900P1, -4160KP1, -4220KP1, -4280KP1 VFP7-2900P, -2110KP, -4200KP, -4220KP, -4280KP, -4315KP Step 1: Remove the inverter fitting metal ① (4 pcs), ② hanging metal ② (2 pcs) and screw ③ (4 pcs) ②...
The following illustrates the cutout in the panel to install the inverter with the attachment. (The size of the cutout in the panel is shown in mm.) ATFIN7*5 ATFIN7*6 VFA7-2370P1∼2550P1, 4370P1∼4750P1 VFA7-2750P1, 4110KP1,4132KP1 VFP7-2370P∼2550P, 4450P∼4900P VFP7-2750P, 4110KP∼4160KP Common size (Refer to Figure 7.) Common size (Refer to Figure 8.)
E6581187 4. Outward appearance Outward appearances of the inverter with the attachment are roughly shown in Figure 10, 11 and 12. (Unit of size: mm) ATFIN7*5 VFA7-2370P1∼2550P1, 4370P1∼4750P1 VFP7-2370P∼2550P, 4450P∼4900P Common size (Refer to Figure 10.) Inside of panel ―――――――――...
Page 10
E6581187 ATFIN7*6 VFA7-2750P1, 4110KP1,4132KP1 VFP7-2750P, 4110KP∼4160KP Common size (Refer to Figure 11.) Inside of panel ――――――――― ――――――――― ――――――――― ――――――――― Outside of panel Figure 11 -9-...
Page 11
E6581187 ATFIN7*7 VFA7-2900P1, 4160KP1∼4280KP1 VFP7-2900P,2110KP, 4200KP∼4315KP Common size (Refer to Figure 12.) Inside of panel 図9 ―――――――― ―――――――― ―――――――― ―――――――― Outside of panel Figure 12 -10-...