Toshiba TOSVERT VF-P7 Instruction Manual page 219

[28] Protection functions
Communi
Title Function
cation No
 0600 Motor overload protection level #1 10∼100 [%]
 0601 Stall prevention level
0602 Selection of inverter trip holding

 0603 Emergency stop
Emergency DC injection
 0604
braking control time
0605 Output phase failure detection 0: Disabled, 1: Enabled

0606 Overload reduction start-up frequency 0.0∼30.0 [Hz]

 0607 Motor 150%-overload time limit 10∼2400 [s]
Relay injection timing for
 0608
rush-current suppression
0609 Mode of rush-current suppression relay 0: Standard, 1: in relation to ST

0610 Low current trip

 0611 Low current detection level
 0612 Low current detection time
Detection of output short-
0613

circuit during start-up
Adjustment of detection pulse for
0614 output short-circuit during start-up 1∼100 [μs]

 0615 Over-torque trip
Over-torque detection level
 0616
during power running
Over-torque detection level
0617

during regeneration
0618 Over-torque detection time

 0620 Cooling fan control mode
 0621 Cumulative operation time alarm setting 0.1∼999.9 [×100h]
0622 Abnormal speed detection filter 0.01∼100.0 [s] (*1)

0623 Over-speed detection frequency range 0: Disabled, 0.1∼30.0 [Hz]

 0624 Speed drop detection frequency range 0: Disabled, 0.1∼30.0 [Hz]
Over-voltage stall protection
 0625
level (high response)
0626 Over-voltage stall protection level 50∼250 [%]

0627 Under-voltage trip mode

 0628 Under-voltage detection time 0.00∼10.00 [s]
 0629 Under-voltage stall level
0630 System-supporting sequence(B-timer)

0631 Position deviation limit

 0632 Brake release inhibition time after run 0.00: Setting of  is valid, 0.01∼2.50 [s]
The trip selection at the VI/II
 0633
low-level input
(*1): Set a time longer than the acceleration/deceleration time.
※(Reference section): Refer to the inverter's individual manual.
Adjustment range
0∼199 [%], 200: Disabled
0: Cleared if power is turned off
1: Held even if power is turned off
0: Coast stop 1: Deceleration stop
2: Emergency DC injection braking stop
3: Coast stop without FL output
4: Deceleration stop without FL output
5: Emergency DC injection braking without FL output
0.0∼10.0 [s]
0.3∼2.5 [s]
0: Disabled, 1: Enabled
0∼100 [%]
0∼255 [s]
0: Standard
1: Only one time at power injection or at first start after reset
0: Disabled, 1: Enabled
0∼250 [%]
0∼250 [%]
0.0∼100.0 [s]
0: Automatic, 1: Always ON
50∼250 [%]
0: Disabled, 1: Enabled
50∼100 [%]
0.0: Invalid, 0.1∼10.0 [s]
0.1∼6553
0∼100
Sensorless vector/vector with sensor (●valid, −:invalid)
Min. unit (panel/ Default Write during
Speed
communication) setting running
control
1/0.01 100 Enabled ●/●
1/0.01 120 Enabled ●/●
0 Disabled
− ●/●
− 0 Disabled ●/●
0.1/0.01 0.1 Enabled ●/●
0 Disabled
− ●/●
0.01/0.01 6.0 Enabled
●/●
1/1 600 Enabled ●/●
0.1/0.01 0.3 Disabled ●/●
0 Disabled
− ●/●
0 Disabled
− ●/●
1/0.01 0 Enabled ●/●
1/1 0 Enabled ●/●
0 Disabled
− ●/●
1/1 50 Disabled
●/●
− 0 Enabled ●/●
1/0.01 120 Enabled ●/●
1/0.01 120 Enabled
●/●
0.1/0.01 0.5 Enabled
●/●
− 0 Enabled ●/●
0.1/0.1 175.0 Enabled ●/●
0.01/0.01 10.00 Enabled
−/●
0.01/0.01 0.0 Enabled
−/●
0.01/0.01 0.0 Enabled −/●
1/0.01 135 Enabled ●/●
1/0.01 130 Enabled
●/●
0 Disabled
− ●/●
0.01/0.01 0.03 Disabled ●/●
1/0.01 75 Enabled ●/●
0.1/0.01 0.0 Enabled
●/●
0.1/0.1 16 Disabled
−
0.01/0.01 0.00 Disabled ●/●
1/1 0.00 Enabled ●/●
Vector control
V/f Reference
Torque Position
Constant section
control control
●/● −/● ● 5.13
−/− −/● ● 6.25.2
6.25.3
●/● −/● ●
●/● −/● ● 6.25.4
●/● −/● ● 6.25.4
●/● −/● ● ※
5.13
●/● −/● ●
●/● −/● ● 5.13
●/● −/● ● ※
●/● −/● ● ※
6.25.7
●/● −/● ●
●/● −/● ● 6.25.7
●/● −/● ● 6.25.7
6.25.8
●/● −/● ●
6.25.8
●/● −/● ●
●/● −/● ● 6.25.9
●/● −/● ● 6.25.9
6.25.9
●/● −/● ●
6.25.9
●/● −/● ●
●/● −/● ● 6.2510
●/● −/● ● 6.25.11
−/− −/− −/− ※
−/− −/− − ※
−/− −/− − ※
− − ● 6.13.5
6.13.5
− − ●
6.25.13
●/● −/● ●
●/● −/● ● 6.25.14
●/● −/● ● 6.25.15
●/● −/● ● ※
− −/● − ※
●/● −/● ● ※
●/● −/● ● ※