Mitsubishi Electric MELSERVO-J3 Series Manual page 449

14. OPTIONS AND AUXILIARY EQUIPMENT
(b) When using the 600V Grade heat-resistant polyvinyl chloride insulated wire (HIV wire)
Selection example of wire size when using HIV wires is indicated below. For the wire ( 8)) for power
regeneration converter (FR-RC-(H)), use the IV wire indicated in (1) (a) in this section.
Servo amplifier
1)
L L
1 2
MR-J3-10T(1)
MR-J3-20T(1)
MR-J3-40T(1)
MR-J3-60T 2(AWG14)
MR-J3-70T
MR-J3-100T
MR-J3-200T
MR-J3-350T 3.5(AWG12)
MR-J3-500T
5.5(AWG10): a
(Note 2)
MR-J3-700T
8(AWG8): b
(Note 2)
MR-J3-11KT
14(AWG6): c
(Note 2)
MR-J3-15KT
22(AWG4): d
(Note 2)
MR-J3-22KT
38(AWG1): p
(Note 2)
MR-J3-60T4
MR-J3-100T4 2(AWG14)
MR-J3-200T4
MR-J3-350T4 2(AWG14): g
MR-J3-500T4
(Note 2)
3.5(AWG12): a
MR-J3-700T4
(Note 2)
MR-J3-11KT4
5.5(AWG10): j
(Note 2)
MR-J3-15KT4
8(AWG8): l
(Note 2)
MR-J3-22KT4
14(AWG6): m
(Note 2)
Note 1. Alphabets in the table indicate crimping tools. For crimping terminals and applicable tools, refer to (1) (c) in this section.
2. When connecting to the terminal block, be sure to use the screws which are provided with the terminal block.
3. For the servo motor with a cooling fan.
4. Wires are selected based on the highest rated current among combining servo motors.
Table 14.2 Wire size selection example 2 (HIV wire)
2) L L
11 21
L U V W
3
1.25(AWG16)
1.25(AWG16)
1.25(AWG16)
2(AWG14)
3.5(AWG12)
5.5(AWG10): a 2(AWG14): g
1.25(AWG16):
h
8(AWG8): b
14(AWG6): c
1.25(AWG16):
22(AWG4): d
g
38(AWG1): p
1.25(AWG16)
1.25(AWG16)
2(AWG14)
2(AWG14): g
1.25(AWG16):
3.5(AWG12): a
h
5.5(AWG10): a
8(AWG8): l
1.25(AWG16):
14(AWG6): c
g
14(AWG6): m
2
Wires [mm ] (Note 1, 4)
3)
4) P C
2(AWG14)
2(AWG14): g
3.5(AWG12): j 1.25(AWG16)
5.5(AWG10): k
2(AWG14)
2(AWG14): g
2(AWG14): q
3.5(AWG12): j
3.5(AWG12): k
14 - 64
6)
5) B1 B2
BU BV BW
1.25(AWG16)
(Note 3)
1.25(AWG16)
1.25(AWG16)
(Note 3)
1.25(AWG16)
7)
OHS1 OHS2
1.25(AWG16)
(Note 3)
1.25(AWG16)
1.25(AWG16)
(Note 3)
1.25(AWG16)