P492 Analog Monitoring Of Motor Temperature: Trip Temperature; P495 Brush Length Sensing: Tripping Of Alarm Or Fault Message; P496 Bearing Condition: Tripping Of Alarm Or Fault Message; P497 Air Flow: Tripping Of Alarm Or Fault Message - Siemens 6RA70 Series Instructions Manual

PNU Description
P492 Analog monitoring of motor temperature: Trip temperature
FDS
Operative only when P490.x=1.
(G185)
P493 Motor temperature analog 1 (temperature sensor at terminals 22 / 23):
* Tripping of alarm or fault message
FDS
Motor temperature grasped with KTY84
(G185) 0 Monitoring deactivated
1 Alarm (A029) at temperature > P491
2 Fault message (F029) at temperature > P492
3 Alarm (A029) at temperature > P491 and
fault message (F029) at temperature > P492
Motor temperature grasped with PTC thermistor
0 Monitoring deactivated
1 Alarm message (A029) when operating point of PTC thermistor
is reached
2 Fault message (F029) when operating point of PTC thermistor is
reached
3 Illegal setting
P494 Motor temperature analog 2 (temperature sensor at terminals 204 /
* 205): Tripping of alarm or fault message
FDS
Motor temperature grasped with KTY84
0 Monitoring deactivated
(G185)
1 Alarm (A029) at temperature > P491
2 Fault message (F029) at temperature > P492
3 Alarm (A029) at temperature > P491 and
fault message (F029) at temperature > P492
Motor temperature grasped with PTC thermistor
0 Monitoring deactivated
1 Alarm message (A029) when operating point of PTC thermistor
is reached
2 Fault message (F029) when operating point of PTC thermistor is
reached
3 Illegal setting
P495 Brush length sensing: Tripping of alarm or fault message
*
0 No brush length sensing (terminal 211 is not scanned)
FDS
1 Binary brush length sensing (terminal 211 is scanned)
Alarm (A025) in response to 0 signal
(G186)
2 Binary brush length sensing (terminal 211 is scanned)
Fault message (F025) in response to 0 signal
P496 Bearing condition: Tripping of alarm or fault message
*
0 No bearing condition sensing (terminal 212 is not scanned)
FDS
1 Bearing condition sensing (terminal 212 is scanned)
Alarm (A026) in response to 1 signal
(G186)
2 Bearing condition sensing (terminal 212 is scanned)
Fault message (F026) in response to 1 signal
P497 Air flow: Tripping of alarm or fault message
*
0 No air flow monitoring (terminal 213 is not scanned)
FDS
1 Air flow monitoring (terminal 213 is scanned)
Alarm (A027) in response to 0 signal
(G186)
2 Air flow monitoring (terminal 213 is scanned)
Fault message (F027) in response to 0 signal
P498 Temperature switch: Tripping of alarm or fault message
*
0 No temperature switch connected (terminal 214 is not scanned)
FDS
1 Temperature switch connected (terminal 214 is scanned)
Alarm (A028) in response to 0 signal
(G186)
2 Temperature switch connected (terminal 214 is scanned)
Fault message (F028) in response to 0 signal
10-52
Value range
[Unit]
Steps
0 to 200
[°C]
1°C
0 to 3
1
0 to 3
1
0 to 2
1
0 to 2
1
0 to 2
1
0 to 2
1
SIEMENS Energy & Automation
SIMOREG DC Master Base Drive Panel Operating Instructions
No. indices See
Factory Change
setting (Access /
Type Status)
Ind: 4 P052 = 3
FS=0 P051 = 40
Type: O2 Online
Ind: 4 P052 = 3
FS=0 P051 = 40
Type: O2 Offline
Ind: 4 P052 = 3
FS=0 P051 = 40
Type: O2 Offline
Ind: 4 P052 = 3
FS=0 P051 = 40
Type: O2 Offline
Ind: 4 P052 = 3
FS=0 P051 = 40
Type: O2 Offline
Ind: 4 P052 = 3
FS=0 P051 = 40
Type: O2 Offline
Ind: 4 P052 = 3
FS=0 P051 = 40
Type: O2 Offline