Motorized Potentiometer; Connector Selector Switches; P455 Source For Inputs Of Connector Selector Switch 1; P460 Control Word For Motorized Potentiometer Ramp-Function Generator - Siemens 6RA70 Series Instructions Manual

PNU Description
P453 Source for "Enable zero marker counter" command
*
Selection of binector to control enabling of the zero marker counter
BDS
0 = binector B0000
1 = binector B0001
(G145)
etc.

10.23 Connector selector switches

(see also Section 8, Function Diagram Sheet G124 of Operating Instructions 6RX1700-0AD**)
P455 Source for inputs of connector selector switch 1
*
Selection of connectors for the input signals for connector selector switch 1.
(G124)
0 = connector K0000
1 = connector K0001
etc.
P456 Source for control of connector selector switch 1
*
Selection of binectors to control connector selector switch 1.
(G124)
0 = binector B0000
1 = binector B0001
etc.
P457 Source for inputs of connector selector switch 2
*
Selection of connectors for the input signals for connector selector switch 2.
(G124)
0 = connector K0000
1 = connector K0001
etc.
P458 Source for control of connector selector switch 2
*
Selection of binectors to control connector selector switch 2.
(G124)
0 = binector B0000
1 = binector B0001
etc.

10.24 Motorized potentiometer

(see also Section 8, Sheet G126 of Operating Instructions 6RX1700-0AD**)
P460 Control word for motorized potentiometer ramp-function generator
*
0 The motorized potentiometer ramp generator is bypassed in
FDS
Automatic mode (same effect as for P462 and P463 = 0.01, i.e.
the generator output is made to follow the automatic setpoint
(G126)
without delay)
1 Motorized potentiometer ramp generator is active in Manual and
Automatic modes
P461 Source for setpoint in Automatic mode
*
Selection of the connector to be applied as the Automatic setpoint to the
FDS
ramp-function generator in the motorized potentiometer
(G126) 0 = connector K0000
1 = connector K0001
etc.
P462 Ramp-up time for motorized potentiometer
FDS
(G126)
P463 Ramp-down time for motorized potentiometer
FDS
(G126)
SIEMENS Energy & Automation
SIMOREG DC Master Base Drive Panel Operating Instructions
Value range
[Unit]
Steps
[SW 1.9 and later] All binector numbers
1
All connector
[SW 1.9 and later]
numbers
1
All binector numbers
[SW 1.9 and later]
1
[SW 1.9 and later] All connector
numbers
1
[SW 1.9 and later] All binector numbers
1
0 to 1
1
All connector
numbers
1
0.01 to 300.00
[s]
0.01s
0.01 to 300.00
[s]
0.01s
No. indices See
Factory Change
setting (Access /
Type Status)
Ind: 2 P052 = 3
FS=1 P051 = 40
Type: L2 off-line
Ind: 3 P052 = 3
FS=0 P051 = 40
Type: L2 off-line
Ind: 2 P052 = 3
FS=0 P051 = 40
Type: L2 off-line
Ind: 3 P052 = 3
FS=0 P051 = 40
Type: L2 off-line
Ind: 2 P052 = 3
FS=0 P051 = 40
Type: L2 off-line
Ind: 4 P052 = 3
FS=1 P051 = 40
Type: O2 Offline
Ind: 4 P052 = 3
FS=0 P051 = 40
Type: L2 Offline
Ind: 4 P052 = 3
FS=10.00 P051 = 40
Type: O2 Online
Ind: 4 P052 = 3
FS=10.00 P051 = 40
Type: O2 Online
10-49