Analog Inputs (Main Actual Value, Main Setpoint, Selectable Inputs); P700 Signal Type Of "Main Setpoint" Analog Input; P701 Normalization Of "Main Setpoint" Analog Input; P705 Filtering Time For "Main Setpoint" Analog Input - Siemens 6RA70 Series Instructions Manual

PNU Description
P696 Source for selection of "Stop speed controller I component" function
*
Selection of binector to control the "Stop I component" function
BDS
0 = binector B0000
1 = binector B0001
(G152)
etc.
When the binector selected in P696 changes to the log. "1" state, the I
component of the speed controller is stopped.
P697 Source for selection of enabling of dv/dt injection
*
Selection of binector to control enabling of dv/dt injection (state "1" =
BDS
enable)
(G153) 0 = binector B0000
1 = binector B0001
etc.
P698 Source for selection of enabling command for speed-dependent speed
* controller PI / P function switchover
BDS
Selection of binector to control enabling of the speed-dependent PI / P
controller switchover function (see also P222)
(G152)
0 = binector B0000
1 = binector B0001
etc.

10.37 Analog inputs (main actual value, main setpoint, selectable inputs)

(see also Section 8, Sheets G113 and G114 of Operating Instructions 6RX1700-0AD**)
Analog input terminals 4 / 5 (main setpoint)
P700 Signal type of "Main setpoint" analog input
*
0 = Voltage input 0 to ± 10 V
1 = Current input 0 to ± 20 mA
(G113)
2 = Current input 4 to 20 mA
P701 Normalization of "Main setpoint" analog input
This parameter specifies the percentage value which is generated for an
FDS
input voltage of 10V (or an input current of 20mA) at the analog input.
The following generally applies:
(G113)
For voltage input:
[%] = ∗
P 701 10 V
With current input:
[%] = ∗
P 701 20 mA
P702 Offset for "Main setpoint" analog input
(G113)
P703 Mode of signal injection at "Main setpoint" analog input
*
0 = Injection of signal with sign
1 = Injection of absolute value of signal
(G113)
2 = Injection of signal with sign, inverted
3 = Injection of absolute value of signal, inverted
P704 Source for selection of sign reversal at "Main setpoint" analog input
*
Selection of binector to control sign reversal at the analog input ("1" state
= reverse sign)
(G113)
0 = binector B0000
1 = binector B0001
etc.
P705 Filtering time for "Main setpoint" analog input
Note: Hardware filtering of approximately 1 ms is applied as standard.
(G113)
SIEMENS Energy & Automation
SIMOREG DC Master Base Drive Panel Operating Instructions
Y
X .. Input voltage in volts
X
Y .. % value which is generated for input
voltage X
Y
X .. Input current in mA
X
Y .. % value which is generated for input
current X
Value range No. indices
[Unit] Factory
Steps setting
Type
All binector numbers Ind: 2
1 FS=0
Type: L2
All binector numbers Ind: 2
1 FS=1
Type: L2
All binector numbers Ind: 2
1 FS=1
Type: L2
0 to 2 Ind: None
1 FS=0
Type: O2
-1000.0 to 1000.0 Ind: 4
[%] FS=100.0
0.1% Type: I2
-200.00 to 199.99 Ind: None
[%] FS=0.00
0.01% Type: I2
0 to 3 Ind: None
1 FS=0
Type: O2
All binector numbers Ind: None
1 FS=0
Type: L2
0 to 10000 Ind: None
[ms] FS=0
1ms Type: O2
See
Change
(Access /
Status)
P052 = 3
P051 = 40
Offline
P052 = 3
P051 = 40
Offline
P052 = 3
P051 = 40
Offline
P052 = 3
P051 = 40
Offline
P052 = 3
P051 = 40
Online
P052 = 3
P051 = 40
Online
P052 = 3
P051 = 40
Offline
P052 = 3
P051 = 40
Offline
P052 = 3
P051 = 40
Online
10-71