Siemens SIMOCODE pro Operating Manual page 276

Index
Number of starts - overshoot, 151
Number of starts - prewarning, 151
O
OFF command reset, 211
OM SIMOCODE pro, 26
OPC UA Receive, 198
OPC UA receive data 0 (1, 2/3), 19
OPC UA send data 0 (1), 18
OPC-UA send, 162, 180
OPC-UA Send Data, 180
Operating hours monitoring, 151, 152
Operating modes, 56
Operation monitoring, 16, 151
Operational Protection Off, 203
Operational Protection Off (OPO), 16, 213
Operational Protection Off settings, 214
Operator panel [OP] control station, 60
Operator panel buttons, 16, 183, 186
Operator panel LED, 16
Operator panel LED settings, 167
Operator panel LEDs, 165
Output modes, 162
Output of the effective motor current
Entire range, 172
Part of range, 174
Output response of the timer, 244
Outputs, 161
Overload, 119
Overload characteristics for 2nd generation current /
voltage measuring modules (e.g.
3UF7110-1AA01-0), 39
Overload characteristics for current measuring
modules and 1st generation current / voltage
measuring modules (e.g. 3UF7110-1AA00-0) and
2nd generation current / voltage measuring modules in
compatibility mode (e.g. 3UF7110-1AA01-0), 41
Overload relay, 61, 67
Overload relay control function, 72
Overload relay settings, 73
Overtemperature, 51, 158
P
Panel reset, 211
Parameters for control functions, 68
Pause time, 46
Permissible starts, number of starts monitoring, 154
Phase balance formula, 48
Phase unbalance, 48
PLC / PCS monitoring, 227, 227
276
Plugs, analog, 12
Plugs, binary, 12
Pole-changing reversing starter, 61, 67, 103, 119
Pole-changing reversing starter control function, 100
Pole-changing reversing starter settings, 103
Pole-changing starter, 61, 67, 99, 119
Pole-changing starter control function, 97
Pole-changing starter settings, 99
Positioner, 61, 110, 214
Positioner (1, 2, 3, 4, 5), 67
Positioner 1, 119
Positioner 2, 119
Positioner 3, 119
Positioner 4, 119
Positioner 5, 119
Positioner control, 110
Positioner control function, 107
Power failure monitoring (UVO), 203, 216
Power failure time, 218
Power monitoring, 21
Powerpack for SIMOCODE ES 2007 Basic, 29
Powerpack for SIMOCODE ES 2007 Standard, 29
Powerpack for SIMOCODE ES V14 Basic, 28
Powerpack for SIMOCODE ES V14 Standard, 28
Pre-trigger, 199
Pre-warning level, 47
PROFIBUS DPV1, 197
Protection/Control, 19, 63
PTC, 50
PTC thermistor, 50
Pulse width modulator, 19
Pulse width modulator formulas, 270
R
Relay test, 206
Remote operation, 56
Remote reset, 211
Reset, 47, 203
Reset 1 (2, 3), 19
Reset bus / PLC fault, 228
Reset function, 205, 205
Reset settings, 207
Residual current, 130
Resistive load, 69
Response, 8
Response - Monitoring interval for mandatory
testing, 159
Response to other control functions, OPO, 215
Response to overshooting the number of starts,
number of starts monitoring, 155
Response to sensor fault, ground-fault monitoring, 134
Operating Manual, 04/2017, A5E40507630002A/RS-AA/001
SIMOCODE pro - Parameterize