Siemens SIMOCODE pro Operating Manual page 274

Index
Circuit and parameterization for truth table 3I / 1O, 236
Circuit breaker, 61, 81, 119
Circuit breaker settings, 81
Class, 38
Class time, 49
Cold run, 209
Connecting plugs with sockets, 14
Contactor control with control functions, 120
Contactor controls, 63
Control
commands, 76, 79, 82, 86, 90, 93, 97, 100, 104, 107,
112, 115
Control function settings for Dahlander reversing
starter, 96
Control functions, 61
Control of lamps for displaying operating states, 164
Control station local control, 53, 60
Control station operator panel, 55
Control station PC, 54, 60
Control station PLC/PCS, 53, 60
Control station settings, 60
Control stations, 20, 53
Cooling-down period, 43
Cos phi monitoring, 20, 143
Counter 1 (2, 3, 4, 5, 6), 22
Counter settings, 241
Counters, 240
Cross-circuit detection, 223
Current limit monitoring, 135
Current limits, 20
Current measuring module installed in delta / in the
supply cable, 70, 85, 90
Current notes on operational safety, 11
Current setting Is2, 35
Current threshold, 49
Cyclic PROFIBUS DP services, 178
Cyclic receive, 183, 196
Cyclic receive byte 0 (1, 2/3, 4/5), 23
Cyclic send, 177
Cyclic send byte 0 (1, 2/3, 4/9, 10/10), 23
Cyclic send data, 178, 178
Cyclic services, 196
Cyclic services for PROFINET / EtherNet/IP, 178
D
Dahlander, 61, 67, 92, 119
Dahlander control function, 90
Dahlander reversing starter, 61, 67, 96, 119
Dahlander reversing starter control function, 93
Dahlander settings, 92
Debounce time for inputs, 191
274
Delay prewarning, 47
Diagram of enables and enabled control command, 58
Digital module 1 (2) inputs, 17
Digital module 1 (2) inputs, DM-F = DM-F Local or
DM-F PROFIsafe, 17
Digital module 1 (2) outputs, 17
Digital module 1 inputs, 183
Digital module 2 inputs, 183
Digital module inputs, 188
Digital module outputs, 168
Direct starter (direct-on-line starter), 61, 67, 75, 119
Direct starter (direct-on-line starter) control function, 74
E
EEx e applications, 43, 51, 158
Emergency start, 18, 203, 219, 219
Emergency start settings, 219
Enabled command - example, 59
Enables, 58
Engineering software migration from V7 to V8, 30
Engineering software V7, 30
Engineering software V8, 30
Ethernet - OPC-UA Receive, 183
Example - Pulse width modulator, 271
Example of a truth table for 3I / 1O, 235
Example of truth table 2I/1O, 238
Examples of calculators, 264
Examples of typical units and ranges in
SIMOCODE pro, 260
Execution
time, 69, 75, 78, 81, 85, 89, 92, 96, 99, 103, 106, 111,
114, 118
Extended control, 17, 65
Extended protection, 17
Extended protection ("overload protection," "unbalance
protection," and "stalled rotor protection"), 32
Extended status and fault messages, 64
external fault, 210
External fault, 203, 211
External fault 1(2, 3, 4, 5, 6), 17
External ground-fault monitoring, 123
External ground-fault monitoring (with 3UL22 residual
current transformer), 131
External ground-fault monitoring (with 3UL23
summation current transformer), 127
External ground-fault monitoring (with summation
current transformer 3UL23), 132
Operating Manual, 04/2017, A5E40507630002A/RS-AA/001
SIMOCODE pro - Parameterize