Counter (Counter Mode) - Canon iR C3380 series Service Manual

FLYING
PP-LWRT
USB-RCNT
2. USER
Sub item
COPY-LIM
SLEEP
COUNTER 1
COUNTER 2
COUNTER 3
COUNTER 4
COUNTER 5
COUNTER 6
CONTROL
B4-L-CNT
COPY-JOB
Setting whether to initiate a flying start
This is set to "1" when a flying start is not to be initiated in consideration of the service life of the fixing unit. Normally,
after a job is completed, operation is controlled so that the fixing is performed and the takes of the polygons are made
longer in preparation for the next job, but this control is not performed when the item is set to "1."
Settings
0: A flying start is initiated.
1: A flying start is not initiated.
[Factory setting/value after clearing RAM: 0]
Not used
Setting for automatic connection when USB device is disconnected
This sets whether automatic re-connection is to be initiated when the USB device is disconnected (USB reconnect).
Settings
0: No automatic connection
1: Automatic connection is initiated.
[Factory setting/value after clearing RAM: 0]
Specification selection related to user mode
Used to change upper limit value setting for number of sheets to copy.
Setting values
1 to 999 sheets [Factory default/After RAM clear: 999]
Used to turn sleep function ON/OFF.
Setting values
0: OFF
1: ON [Factory default/After RAM clear]
Reference:
The sleep function is set by the timer setting in the "User mode"
Counter status verification screen soft counter 1 setting
This makes it possible to change the type display of soft counter 1 on the control unit to suit the demand from users and
dealers.
Setting
101: Total 1
[Factory setting/value after clearing RAM: Fixed at 1 -> Cannot be changed]
Counter status verification screen soft counter 2 setting
This makes it possible to change the type display of soft counter 2 on the control unit to suit the demand from users and
dealers.
Setting range: 0 to 999
[Factory setting/value after clearing RAM: 108]
Counter status verification screen soft counter 3 setting
This makes it possible to change the type display of soft counter 3 on the control unit to suit the demand from users and
dealers.
Setting range: 0 to 999
[Factory setting/value after clearing RAM: 232]
Counter status verification screen soft counter 4 setting
This makes it possible to change the type display of soft counter 4 on the control unit to suit the demand from users and
dealers.
Setting range: 0 to 999
[Factory setting/value after clearing RAM: 324]
Counter status verification screen soft counter 5 setting
This makes it possible to change the type display of soft counter 5 on the control unit to suit the demand from users and
dealers.
Setting range: 0 to 999
[Factory setting/value after clearing RAM: 000]
Counter status verification screen soft counter 6 setting
This makes it possible to change the type display of soft counter 6 on the control unit to suit the demand from users and
dealers.
Setting range: 0 to 999
[Factory setting/value after clearing RAM: 000]
Switch for selecting whether to charge fees for PDL jobs
This selects whether to output count pulses to the charge management system (coin vendor or control card made by
another company) when such a system is connected.
Settings
0: Fees are not charged.
1: Fees are charged.
[Factory setting/value after clearing RAM: 0]
This item is set to "1" when fees are charged for PDL prints.
Used to select whether to count B4 size paper as large size or small size for software counters 1 to 6.
Setting values
0: Small size [Factory default/After RAM clear]
1: Large size
Prohibits copy job reservations when card reader and coin vendor are in use.
Setting values
0: Copy job reservations [Factory default/After RAM clear]
1: No copy job reservations
COPIER>OPTION>BODY
T-17-55
COPIER>OPTION>USER
Description
Chapter 17
2
2
2
level.
1
1
1
1
1
1
1
1
1
1
1
17-59