Add / Delete Keyfob Transmitters - Visonic PowerMaster-10 G2 User Manual

1
For detailed instructions on how to select User Settings – refer to sections A.1 and A.2.
2
The display shows the first enrolled Tag (Tag No.1) of the 8 tags (PowerMaster-10 G2) / 32 tags
(PowerMaster-30 G2).
3
To abort enrollment press the
4
If the tag was previously enrolled in the system, the PowerMaster display reads [
and then switches to the name of the tag alternating with its ID number.
5
If Partition is enabled, continue to step 6.
6
You can now enroll another proximity tag. You can also select another option in the User Settings menu
(see section A.1), or quit programming (see section A.2).
7
If no proximity tag is enrolled in the system, the display reads [
8
To abort the procedure, press the
9
This setting can be performed only after completing steps 1 - 5 of section B.5A.
10
The symbol now appears next to the newly selected Partitions.
11
You can now repeat steps 2 - 7 to program or edit another Proximity tag.
12
You can now add or delete another proximity tag. You can also select another option in the User Settings
menu (see section A.1 and section A.2), or quit programming (see section A.3).
B.7 Add / Delete Keyfob Transmitters
A portable keyfob transmitter may be assigned to each of the PowerMaster-10 G2 user codes 1-8 /
PowerMaster-30 G2 user codes 1-32 for better, quicker and safer arming/disarming and other control functions.
Each keyfob should be assigned with a serial No. 1-8 (PowerMaster-10 G2) / 1-32 (PowerMaster-30 G2) and
enrolled into the system correspondingly.
Partition Option (For information about Partition option - see Appendix B)
If the Partition option is enabled in the control panel, each of the 8 keyfobs (PowerMaster-10 G2) / 32 keyfobs
(PowerMaster-30 G2) can be authorized by the Master User to arm and disarm any combination, or all 3
partitions, irrespective of the authorization of its corresponding user code.
♦ Here you can add (enroll) the 8 (PowerMaster-10 G2) / 32 (PowerMaster-30 G2) Keyfob transmitters and
define which of the 3 partitions each of the keyfob will be authorized to arm and disarm, or delete keyfobs as
required.
1. Before anything else, gather up all keyfob units you intend to enroll and make sure they all have
batteries installed and that they are active (the LED blinks upon pressing any of the buttons).
2. Carefully read the section titled "Additional Information" according to the indicated references
see table at end of this section.
A. To Add (Enroll) a Keyfob
1.
KEYFOBS
2.
ADD NEW KEYFOB
3.
ENROLL NOW or
ENTR ID:xxx-xxxx
4a.
DEVICE ENROLLED
☺ Go to step 5
D-304829 PowerMaster-10/30 G2 User's Guide
Additional Information (section B.6)
button.
button.
Enter the [USER SETTINGS] menu, select the [KEYFOBS] option and press
1
.
The display will read [ADD NEW KEYFOB].
To enroll a new keyfob press
The display offers you two alternative methods to enroll a keyfob:
A: ENROLL NOW: Press and hold the AUX
until the LED is constantly on.
If enrollment was successfully completed, a "Happy Tune"
the display reads [DEVICE ENROLLED] for a short duration and then
changes to read the keyfob's details. Continue to step 5.
MENUS AND FUNCTIONS
ALREADY ENROLLED
NO EXISTING DEV.
].
4
.
button on the selected keyfob
2
This procedure completes the enrollment.
]
1
etc –
☺ sounds and
29