Enrolling Wireless Devices And Keyfob Transmitters; General Guidance; Enrolling Type; Enroll/Delete Sensors - Visonic POWERMAXCOMPLETE - INSTALLER GUIDE Manual

1. NEW INSTL CODE
NEW INST. CODE
INST. CODE xxxx
Figure 4.1b - Setting a New Installer Code (see note)

4.2 ENROLLING WIRELESS DEVICES AND KEYFOB TRANSMITTERS

4.2.1 General Guidance

The ENROLLING mode has the following sub-modes:
• ENROLLING TYPE (wireless devices)
• ENROLL SENSORS.
ENROLL KEYFOB
transmitters)
• ENROLL WL 1WAY KP (wireless commander MCM-140+)
• ENROLL WL 2WAY KP (wireless 2-way keypad MKP-150/
MKP-151)
Note: This sub-mode will be hidden if Partition is
enabled.
• ENROLL WL SIREN (wireless siren)
• ENROLL PROX TAG (proximity tag)
Before beginning, gather all the devices that you intend to
enroll and make sure they all have batteries installed.
Your control panel must recognize the unique identification
code (ID) of each such device in order to supervise them,
receive their signals and respond accordingly.
Attention! CodeSecure transmitters are mainly used for
arming/disarming and can not be enrolled to zones. In
order to enroll to zones, use only non-CodeSecure
wireless devices.

4.2.2 Enrolling Type

Here you determine whether to enroll a wireless device by
normal transmission or by device Tamper function
(opening its cover). Options: normal, or by tamper.

4.2.3 Enroll/Delete Sensors

For PowerMaxComplete
Magnetic contact or any other contact (not a detector) can
be enrolled in zone 29 and wireless detectors can be
enrolled in zones 01-28.
For PowerMaxComplete with expander module: Wired
detectors can be enrolled in zones 29&30 and wireless
detectors can be enrolled in zones 01-28.
Note: Wired zones need to be enrolled in the ENROLLING
menu before they are active.
• Before enrolling, the lens at the front of PIR
STOP
and dual-technology sensors should be
masked to prevent inadvertent transmission.
• Make sure that magnetic contact transmitters are
together with their magnets, to prevent them from
sending alarm transmissions.
To enroll / delete wired / wireless sensors, refer to Fig. 4.2.

4.2.4 Enroll/Delete Keyfob Transmitters

Keyfob transmitters are multi-button wireless CodeSecure™
transmitters. Eight system users use them for better,
quicker and safer control over various system functions.
To enroll / delete 1-way or 2-way keyfob transmitters, refer
to figure 4.2.
12
(See fig. 4.1a)
[code]
(multi-button CodeSecure
without expander
By using
INSTALLER CODE
(see fig. 4.1a)
1. NEW INSTL CODE
NEW INST. CODE
INST. CODE xxxx
[code]
Figure 4.1c - Setting a New Installer Code
in System with Inst. & Master Inst. Codes (see note)
Installer
Note:
"0000". Doing so will lock the user out of the installer menu!

4.2.5 Enroll/Delete Wireless Commander

The Wireless Commander (MCM-140+) is a remote control
unit that enables the user to remotely control the system.
To enroll / delete up to 8 wireless commanders, refer to
figure 4.2 (Enroll WL 1-way KP).

4.2.6 Enroll/Delete 2-Way Keypad

The 2-way keypad, type MKP-150/MKP-151, enables the
user to remotely control the system and also to receive
data from the system (status, alarm and trouble data). To
enroll up to two 2-way keypads, refer to figure 4.2.
Note: MKP-150/151 is not compatible for use when partition
is enabled.

4.2.7 Enroll/Delete Wireless Siren

The wireless siren is a remote siren that is activated upon
predefined events by the PowerMaxComplete system. To
enroll / delete up to 2 wireless sirens, refer to figure 4.2.

4.2.8 Enroll/Delete Proximity Tags

Proximity tags enable authorized people to enter restricted
areas. Presenting valid proximity tag, while the system is
armed, causes the system to disarm. Presenting valid
proximity tag, while the system is disarmed, causes the
system to be armed in AWAY (optional HOME) mode. To
enroll / delete proximity tags, refer to figure 4.2.
Note: Proximity tags are used on control panels with
installed Proximity readers (not standard on UK versions).
Proximity tags are not compatible for use when partition is
enabled.
module:
By using
MASTER INSTALLER CODE
(see fig. 4.1a)
1. NEW INSTL CODE
NEW MASTER CODE
MASTER CODE xxxx
[code]
Code should never be programmed as
NEW INST. CODE
INST. CODE xxxx
[code]
D-302754