Enrolling Wireless Devices And Keyfob Transmitters; General Guidance; Enrolling Type; Enroll/Delete Sensors - Visonic POWERMAX PRO Installer's Manual

1. NEW INSTL CODE
NEW INST. CODE
INST. CODE xxxx
Figure 4.1b - Setting a New Installer Code (see note)

4.2 ENROLLING WIRELESS DEVICES AND KEYFOB TRANSMITTERS

4.2.1 General Guidance

The ENROLLING mode has the following sub-modes:
• ENROLLING TYPE (wireless devices)
• ENROLL SENSORS (enroll wired magnetic contact or
any other contact in zones 29 & 30 / enroll wireless
detectors in zones 01-28).
• ENROLL
KEYFOB
transmitters)
• ENROLL WL 1WAY KP (wireless commander MCM-140+)
• ENROLL WL 2WAY KP (wireless 2-way keypad MKP-
150/151)
Note: This sub-mode will be hidden if Partition is enabled.
• ENROLL WL SIREN (wireless siren)
• ENROLL PROX TAG (proximity tag)
Before beginning, gather all the devices that you intend to
enroll and make sure they all have batteries installed.
Your control panel must recognize the unique identification
code (ID) of each such device in order to supervise them,
receive their signals and respond accordingly.
Attention! CodeSecure transmitters are mainly used for
arming/disarming and can not be enrolled to zones. For
enrolling to zones,
wireless devices.

4.2.2 Enrolling Type

Here you determine whether to enroll a wireless device by
normal transmission or by device Tamper function
(opening its cover). Options: normal, or by tamper.

4.2.3 Enroll/Delete Sensors

Wired and wireless sensors can be enrolled into the
PowerMax Pro. To enroll / delete sensors, refer to Figure
4.2.
• Before enrolling, the lens at the front of PIR
STOP
and dual-technology sensors should be
masked to prevent inadvertent transmission.
• Make sure that magnetic contact transmitters are
together with their magnets, to prevent them from
sending out alarm transmissions.
DE5468IP
(See fig. 4.1a)
[code]
(multi-button CodeSecure
use only non-CodeSecure
By using
INSTALLER CODE
(see fig. 4.1a)
1. NEW INSTL CODE
1. NEW INSTL CODE
NEW MASTER CODE
NEW INST. CODE
MASTER CODE xxxx
INST. CODE xxxx
[code]
Figure 4.1c - Setting a New Installer Code
in System with Inst. & Master Inst. Codes (see note)
Note: Installer Code should never be programmed as
"0000". Doing so will lock the user out of the installer menu!

4.2.4 Enroll/Delete Keyfob Transmitters

Keyfob transmitters are multi-button wireless CodeSecure™
transmitters. Eight system users use them for better,
quicker and safer control over various system functions.
To enroll / delete 1-way or 2-way keyfob transmitters, refer
to Figure 4.2.

4.2.5 Enroll/Delete Wireless Commander

The Wireless Commander (MCM-140+) is a remote control
unit that enables the user to remotely control the system.
To enroll / delete up to 8 wireless commanders, refer to
Figure 4.2 (Enroll WL 1-way KP).

4.2.6 Enroll/Delete 2-Way Keypad

The 2-way keypad, type MKP-150/151, enables the user to
remotely control the system and also to receive data from
the system (status, alarm and trouble data). To enroll up to
two 2-way keypads, refer to Figure 4.2.
Note: MKP-150/151 is not compatible for use when
partition is enabled.

4.2.7 Enroll/Delete Wireless Siren

The wireless siren is a remote siren that is activated upon
predefined events by the PowerMax Pro system. To enroll
/ delete up to 2 wireless sirens, refer to Figure 4.2.

4.2.8 Enroll/Delete Proximity Tags

Proximity tags enable authorized people to enter restricted
areas. Presenting valid proximity tag, while the system is
armed, causes the system to disarm. Presenting valid
proximity tag, while the system is disarmed, causes the
system to be armed in AWAY (optional HOME) mode. To
enroll / delete proximity tags, refer to Figure 4.2.
By using
MASTER INSTALLER CODE
(see fig. 4.1a)
NEW INST. CODE
INST. CODE xxxx
[code] [code]
11