Warning System; Warnings Description List - Panasonic ag-hpx600p Operating Instructions Manual

Warning system

Warnings description list

If an error is detected immediately after the camera turns on or during operation, the <WARNING> lamp and the lamp on the viewfinder screen indicate
the error.
Priority Warning type Viewfinder screen display
[SYSTEM ERROR] factor
1 System error
display*
P2 card removal [TURN POWER OFF] flashes
2
error in red.
[LOW BATTERY] flashes in red
and an empty remaining battery
3 Battery empty indicator bar flashes. (Displayed
even if its display setting is turned
off in the setting menu.)
P2 card fully
4
[ FULL] flashes in red.
recorded
[REC WARNING] factor display*
5 Recording error
flashes in red.
[TEMPORARY PAUSE
Corruption of
6 IRREGULAR FRM SIG] flashes
standard signal
in red.
Low wireless
7 [WIRELESS RF] flashes in red.
signal reception
One remaining battery indicator
bar flashes. (Also displayed when
Battery nearly
8 the [OTHER DISPLAY] item
empty
on the setting menu [DISPLAY
SETUP] screen is set to [OFF].)
P2 card nearly The remaining P2 card capacity
9
full indicator flashes.
*1 [P2 SYSTEM ERROR] factor display
f [P2 MICON ERROR]: P2 microcomputer is not responding.
f [P2 CONTROL ERROR]: Error occurred in the P2 recording control.
f [CAM MICON ERROR]: Camera microcomputer is not responding.
*2 [REC WARNING] factor display
f [CARD ERROR*]: Error in P2 card (the slot number of the error card is displayed on *). Recording will stop.
f [REC RAM OVERFLOW]: Recording RAM overflow. Recording will stop.
f [PULL DOWN ERROR]: Image pull-down error in 24P, 25P, and 30P. Recording continues.
f [OVER MAX NUMBER CLIPS]: An attempt was made to record more than the maximum number of clips (1000) to one P2 card.
f [ERROR]: Other recording errors.
*3 The warning stops if the following operations are made.
f Press the playback related buttons.
f Press the <THUMBNAIL> button.
f Eject the P2 card or insert another card.
*4 The warning stops if the following operations are made.
f Press the <REC> button.
Chapter 10 Maintenance and Inspection — Warning system
Tally lamp
Flashes four
times every
flashes in red.
1
second
Flashes four
times every
second
Flashes once
every second
Flashes four
times every
second after
the recording
finishes
Flashes four
2
times every
second
Flashes four
times every
second
Flashes four
times every
second (for
recording only)
Flashes once
every second
Flashes
once every
second during
recording.
Warning Description of the warning and
lamp recording/playback behavior
Flashes four Error in the P2 microcomputer
times every or control. The current operation
second will stop.
An error occurred in the built-in
Flashes four memory because the P2 card
times every being accessed was ejected.
second Both of the access LEDs flash in
orange.
The battery has run out.
Recording and playback will stop.
illuminated
If the voltage drops further, the
power is automatically turned off.
Lights up after
The P2 card space is used up.
the recording
Recording will stop.*
finishes
Flashes four Error in recording.
times every The recording may stop or
second continue.*
4
Correct recording is not
possible due to corruption of the
<GENLOCK IN> input signal,
and the recording is suspended
temporarily. The clip will be
Flashes four
divided.
times every
f Recording resumes when
second
the signal returns to normal.
However, recording does not
resume in interval recording,
one-shot recording, and loop
recording.
The error indicates poor
Flashes four wireless audio reception
times every condition. Recording continues
second without receiving the wireless
microphone signal.
The battery is about to run out.
Flashes once
The current operation will
every second
continue.*
5
The remaining P2 card capacity
Flashes
is two minutes or less (the
once every
remaining indicator display is less
second during
than one minute). This warning is
recording.
issued only during recording.
– 157 –
Action to take
Check the factor display*
and consult the place of
purchase.
Turn off the power. If the
clip in the ejected P2 card
contains errors, fix the
errors.
Change the batteries.
Delete some clips or insert
a new card.
3
Turn off the power and on
again, and then check your
recording and playback.
If the recording operation
fails, change the P2 card.
Check the <GENLOCK IN>
signal.
Check the microphone
power supply and the
reception status of the
wireless receiver.
Change the batteries as
needed.
Change the P2 cards
as needed or insert an
additional card.
1