Table of Contents
Advertisement
Chapter 9 Connecting to External Devices — Connection through the <USB2.0> terminal
Connection through the <USB2.0> terminal
USB connection to a computer in the device mode
By connecting the camera to a computer via USB 2.0, the P2 card inserted in the camera can be used as mass storage.
Connecting to a computer
1
Connect the USB cable to the <USB2.0> terminal (device).
NOTE
@
t The USB 2.0 cable is not supplied with the camera. Prepare
a commercial USB 2.0 cable (double-shielded for noise
suppression).
t A USB connection cable of up to 5 m is supported, however, a
cable of 3 m or shorter is recommended as preferable.
2
Set the [PC MODE SEL] item on the setting menu [PC/USB/
LAN] screen to [USB DEVICE], and set the [PC MODE] item
to [ON].
For details, refer to "Setting menu basic operations" (page 118).
PC/USB/LAN
PC MODE SEL
PC MODE
NETWORK SEL
P2 BROWSE
PUSH MENU TO EXIT
USB host mode
Connect a hard disk drive (HDD) that supports USB 2.0 to the camera to save the card data, view the saved clips in thumbnail, and write back to the P2
card.
Switching to the USB host mode
1
Set the [PC MODE SEL] item on the setting menu [PC/USB/
LAN] screen to [USB HOST], and set the [PC MODE] item to
[ON].
For details, refer to "Setting menu basic operations" (page 118).
f The camera enters the USB host mode.
<USB2.0> terminal (device)
USB DEVICE
OFF
OFF
OFF
NOTE
@
t The [PC MODE] can be assigned to the <USER> buttons
(<USER MAIN>/<USER1>/<USER2>) at the [USER MAIN],
[USER1], and [USER2] items on the setting menu [SW MODE]
screen respectively. However, when the menu is open, pressing
the <USER> buttons (<USER MAIN>/<USER1>/<USER2>)
does not activate the function.
t Before connecting the camera using the USB cable, install
P2 software to a computer from the CD-ROM provided with
the camera. For the USB driver, select "AG-HPX600". The
USB driver only supports Windows. For details, refer to the
installation manual.
t The camera supports only USB 2.0. Ensure your computer
supports USB 2.0.
t When connecting the camera to a computer via USB, ensure
that no other device is connected to the computer via USB.
t When connecting the camera via USB, do not eject the P2 card.
t When USB is connected, the P2 card access LED turns off
when not accessed.
t When the camera is operating in the USB device mode, no
recording/playback operation or clip thumbnail operation is
allowed.
t When the camera is operating in the USB device mode, the P2
card remaining capacity and status are not displayed. Audio
is not output from the <SDI OUT/IN (OP)> terminal. The audio
level meter is not displayed on the viewfinder and the monitor
connected to the camera.
During USB connection, [USB DEVICE CONNECTED] is displayed
at the center of the viewfinder screen and status area of the [HOME]
screen of SmartUI. If not connected properly, [USB DEVICE
DISCONNECTED] is displayed.
3
Exit the USB device mode.
There are three ways to do so:
f Turn the <POWER> switch of the camera to <OFF>.
f Switch the [PC MODE] item on the setting menu [PC/USB/LAN]
screen to [OFF].
f Press the <USER> buttons (<USER MAIN>/<USER1>/<USER2>)
to which [PC MODE] is assigned.
f During USB host mode, [USB HOST CONNECTED] is displayed at
the center of the viewfinder screen and status area of the [HOME]
screen of SmartUI. If the hard disk drive is not connected properly,
[USB HOST DISCONNECTED] is displayed.
– 146 –
USB DEVICE
CONNECTED
Advertisement
Table of Contents
