AnyTone AT-3318UV Instruction Manual

AnyTone AT-3318UV Instruction Manual

Dual band handheld radio
Hide thumbs Also See for AT-3318UV:
Table of Contents

Advertisement

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AT-3318UV and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for AnyTone AT-3318UV

  • Page 2 DUAL BAND HANDHELD RADIO INSTRUCTION MANUAL...
  • Page 4 Version A: Dual frequency, dual standby, dual display, dual band, single receive channel. MODELS APPLY TO THIS MANUAL AT-3318UV FM transceiver AT-3318UV(Version A) programming software: QPS3318UV_USA PROGRAM CAUTIONS When programming the transceiver, read the factory initial data first, then rewrite the frequency and...
  • Page 5 CAUTIONS transceiver is excellent designed with advanced technology. The following tips will be helpful for you in performing your obligation under warranty and understanding the safety of transceiver usage. 1.Keep the transceiver and accessories away from children. 2.Please do not try to open or modify the transceiver without permission, non-professionals operation may also cause damage.
  • Page 6: Table Of Contents

    TABLE OF CONTENTS UNPACKING ........................................01 Supplied Accessories ..................................01 STANDARD ACCESSORIES/ADDITIONAL ACCESSORIES ....................02 Standard Accessories ..................................02 Additional Accessories ..................................02 OPERATION MODE (AMATEUR TRANSCEIVER OR PROFESSIONAL TRANSCEIVER) ......... 03 WORKING MODE (AMATEUR TRANSCEIVER OR PROFESSIONAL TRANSCEIVER) ........04 BATTERY INFORMATION ..................................
  • Page 7 TABLE OF CONTENTS Switch between Channel mode and VFO mode ........................16 Channel Adjusting ....................................16 Frequency Adjusting ..................................... 16 Frequency Input by Keypad ................................17 Channel Input by Keypad .................................. 17 Squelch Off Momentary / Squelch Off ............................18 Receiving ........................................
  • Page 8 TABLE OF CONTENTS CTCSS/DCS Encode and Decode ..............................27 Function Menu Setup ....................................28 CTCSS/DCS Encode Setup ................................28 CTCSS/DCS Decode Setup ................................29 CTCSS/DCS Encode / Decode Synchronous Setup ......................29 5TONE Encode Group Selection ..............................30 2TONE Encode Group Selection ..............................
  • Page 9 TABLE OF CONTENTS Scan Dwell Time Setup ..................................41 Function Icon Stay Time Setup ............................... 42 LCD Backlight Setup .................................... 42 LCD Backlight Color Setup ................................43 Self ID Inquiry ......................................43 Tone Pulse Frequency Selection ..............................44 Battery Save Setup ....................................
  • Page 10: Unpacking

    UNPACKING Please carefully unpack the transceiver. We recommend that you identify the items listed in the following table before discarding the packing material. If any items are missing or have been damaged during shipment, please contact with dealers immediately. Supplied Accessories Item Number Quantity...
  • Page 11: Standard Accessories/Additional Accessories

    STANDARD ACCESSORIES/ADDITIONAL ACCESSORIES Standard Accessories Antenna* AC Adaptor Battery Charger Hand Strap Li-ion Battery Belt Clip QA09UV1 (12V/500mA) QBC-26L GS01 QB-26L(1500mAh) BC01 155/435MHz QPS-01 Instruction *1.Note: For frequency band of antenna, please refer to label Manual indicated in the bottom of the antenna. Additional Accessories Battery Pack for Car USB Programming...
  • Page 12: Operation Mode (Amateur Transceiver Or Professional Transceiver)

    OPERATION MODE (AMATEUR TRANSCEIVER OR PROFESSIONAL TRANSCEIVER) The transceiver is a high performance amateur transceiver with dual band, dual standby, dual display and other kinds of functions. According to practical application, you can set the radio to operate as Amateur Transceiver or Professional Transceiver.
  • Page 13: Working Mode (Amateur Transceiver Or Professional Transceiver)

    WORKING MODE (AMATEUR TRANSCEIVER OR PROFESSIONAL TRANSCEIVER) VFO Mode(Frequency mode): This mode shows only frequency on the display. Shortcut operation and Channel setting will be changed & stored as the latest value permanently. Once the radio is turned off or changed to new VFO frequency, the value is remained until next change.(As pic 3) Professional Transceiver Mode: When set display mode as "CH", it enters into Professional Transceiver mode.
  • Page 14: Battery Information

    BATTERY INFORMATION Charging Operation The battery is not charged at the factory, please charge it before use. Charge the battery for the first time after purchase or extended storage (more than 2 months) may not bring the battery to its normal operating capacity.
  • Page 15: How To Charge

    BATTERY INFORMATION ▲ Do not recharge the battery if it is already fully charged. This may shorten the life of the battery or damage the battery. ▲ Do not charge the battery or transceiver if it is damp. Dry it before charging to avoid danger. WARNING: When keys or ornamental chains and other electric metals contact with the battery terminals, the battery may cause damage or hurt bodies.
  • Page 16 BATTERY INFORMATION NOTE: When charging a power-on transceiver equipped with battery, the LED will not turn into green to show the full charge status. Only when turn off the transceiver, the LED can indicate normally. Because when the transceiver is power on, it would consumes energy, the charger cannot detect when battery has been fully charged, the charger will charge battery in voltage consumption and fail to indicate correctly.
  • Page 17: Charging Prompt

    BATTERY INFORMATION Charging Prompt 1. Self- examination: When charging, ORANGE light twinkles for 1 second and goes out. That means the charger has passed its self-examination and it can charge the battery normally. If the light remains orange or the red light twinkles, which means the charger can not pass its self-examination or charge the battery. 2.
  • Page 18: Installation & Connection

    INSTALLATION & CONNECTION Installing / Removing the Li-ion Battery 1. Match the three grooves of the battery pack with the corresponding guides on the back of the transceiver and push. 2. Press the battery pack and transceiver firmly together until the release latch on the top of the transceiver locks.
  • Page 19: Installing / Removing The Belt Clip

    INSTALLATION & CONNECTION Installing / Removing the Belt Clip ■ Installing the Belt Clip: Place the belt clip to the corresponding grooves on the back of the transceiver, and then Clockwise screw it. ■ Removing the Belt Clip: Anticlockwise turn screws to remove the belt clip. Installing Optional Speaker / Microphone Unveil the MIC-SP jack cover and then insert the Speaker/Microphone plug into MIC-SP jack.
  • Page 20 INSTALLATION & CONNECTION Installing the Hand Strap Slide the loop of the hand strap through the eyelet on the upper rear of the transceiver, pull the entire hand strap through the loop to secure the hand strap in place.
  • Page 21: Getting Acquainted

    GETTING ACQUAINTED LCD Display On LCD display screen, you will see various icons which stand for the selected functions and sometimes you may forget the meaning of them. Here you will find the following table extremely useful. Frequency VOX Function Reverse Offset Frequency Scan Skip...
  • Page 22 GETTING ACQUAINTED...
  • Page 23 GETTING ACQUAINTED Antenna Selector Knob Power/Volume switch Rotate it clockwise to turn on transceiver, rotate it anticlockwise until heard "click" to turn off the transceiver. When transceiver is power on, rotate it clockwise to increase volume, anticlockwise to reduce volume. TX/RX indicator, RX is GREEN, TX is RED LCD display Displays current frequency/channel and operations...
  • Page 24: Basic Operations

    BASIC OPERATIONS Turn the Radio On & OFF Under power-off state, turn [POWER]/ [VOLUME] clockwise to turn on the transceiver. Under power-on state, turn [POWER]/ [VOLUME] anticlockwise to turn off the transceiver. Adjusting Volume Under power-on state, turn [POWER] / [VOLUME] to adjust volume. Clockwise-up, anticlockwise -down.
  • Page 25: Switch Between Main Band And Sub Band

    BASIC OPERATIONS Switch between Main band and Sub band Under standby state, press key to switch between Main band and Sub band. Arrow indicates the Main band. Switch between Channel mode and VFO mode Under standby state, press key to set main band as Channel mode or frequency mode(VFO).
  • Page 26: Frequency Input By Keypad

    BASIC OPERATIONS NOTE: Channel step:2.5K, 5K, 6.25K, 10K, 12.5K, 20K, 25K, 30K and 50KHz in total 9 for optional. FM radio step frequency is 50K. Frequency Input by Keypad Under frequency mode or FM radio frequency mode, you can directly enter frequency through keypad. 1.
  • Page 27: Squelch Off Momentary / Squelch Off

    BASIC OPERATIONS Squelch Off Momentary / Squelch Off Side key [PF2] can be setup for Squelch off Momentary or Squelch off function by programming software. 1.Squelch off: Press [PF2] key, squelch circuit is not mute, back-ground noise can be heard. Press [PF2] key again, squelch circuit is mute.
  • Page 28: Emergency Alarm

    BASIC OPERATIONS NOTE: When press and hold PTT key, transceiver is transmitting if the red LED light is on, release PTT key to receive calls. Emergency Alarm Under standby state, press and hold [PF1] key which is programmed with ALARM function until LCD displays "ALARM", Emergency alarm function is started.
  • Page 29: Side Key [Pf2] Function Instruction

    BASIC OPERATIONS Side key [PF2] function instruction 1. Squelch off: Press [PF2] key, squelch circuit is not mute, back-ground noise can be heard. Press [PF2] key again, squelch circuit is mute. 2. Squelch off Momentary: Press and hold [PF2] key, squelch circuit is not mute, back-ground noise can be heard.
  • Page 30: Programming Scan

    BASIC OPERATIONS 3. Press key, the top left corner of LCD displays " " icon, press and hold key until transceiver emits "DUDU" beep and clear up frequency information of current channel, deletion is successful. NOTE: This process can be applied for deleting FM radio channels. Programming scan Setup the frequency of L1 channel, U1 channel, L2 channel and U2 channel will realize VFO frequency scanning border limited.
  • Page 31: Shortcut Operations

    SHORTCUT OPERATIONS Add/Cancel Optional signal decode function Under standby state, press key, the top left corner of LCD displays " " icon, press key. 1. LCD display "DTMF" and " " icon, DTMF signal add in current channel. 2. Repeat above operation, LCD display "5TONE" and " "...
  • Page 32: Offset Frequency Direction Setup

    SHORTCUT OPERATIONS Offset Frequency Direction Setup Under standby state, press key, the top left corner of LCD displays " " icon, press key to choose offset frequency direction. There are 3 options, Positive offset, Minus offset, shut off offset. 1. (+) Positive offset: Indicates TX frequency is higher than RX frequency. When enable reverse function, the RX frequency is higher than TX frequency.
  • Page 33: Channel Scan Skip

    SHORTCUT OPERATIONS in this mode. Press numeric key or key to exit. NOTE: ▼ Frequency scan is of all bands scan, it scans upwards as your STEPPING setting. ▼ In channel scan, the skipped channel is not in the line of scanning. Scan upwards as per channel no. (please refer to channel scan skip).
  • Page 34: Tx Power Selection

    SHORTCUT OPERATIONS if CTCSS/DCS signaling is set, it will also interchange. 2. When "R" icon disappears, it means reverse function is close. TX Power selection Under standby state, press key, the top left corner of LCD displays " " icon, then press key to choose High/Low power for current arrow directed channel.
  • Page 35: Keypad Lock

    SHORTCUT OPERATIONS displays "EMPTY". 3. When current group displays "EMPTY", press key, the top left corner of LCD displays " " icon, press and hold key until transceiver emits "DU" beep, transceiver enters into DTMF edit state, LCD displays "___________", now you can enter desired DTMF data by keypad.
  • Page 36: Single-Band Switching

    SHORTCUT OPERATIONS Single-band Switching To reduce the interference from the sub-channel when the main channel be used. You can use single-band switching function, turn off the sub-channel bands quickly. 1. In standby mode, press the button, the radio will display the PC channel, and turn off the processor channel.
  • Page 37: Function Menu Setup

    FUNCTION MENU SETUP Menu 1-14 of this transceiver are channel operations. Channel operations temporarily changed the functions of current channel. When power off or channel has been changed, the relevant setup will be erased. Only under VFO mode, the channel operations will be saved until next change. Menu 15-45 is background operation(menu 33-44 is memory bank setup, please refer to page 50-51), it is valid for all channels, the relevant setup will be saved until next change.
  • Page 38: Ctcss/Dcs Decode Setup

    FUNCTION MENU SETUP CTCSS/DCS Decode Setup If this function is enabled, you can ignore (can not hear) other unrelated call at the same frequency. 1. Press key, the top left corner of LCD displays " " icon, then press key to enter into function menu. 2.
  • Page 39: 5Tone Encode Group Selection

    FUNCTION MENU SETUP 3. Press key to choose CTCSS, DCS or OFF, when DCS signaling is selected, press key to choose DCS positive or inverse code. 4. Rotate channel switch to choose desired CTCSS/DCSencode/decode. CTCSS: 62.5HZ~254.1HZ, 51groups in total, and 1 group user-defined code. DCS: 000N-777I, 1024 groups in total.
  • Page 40: 2Tone Encode Group Selection

    FUNCTION MENU SETUP 2TONE encode group selection 1. Press key, the top left corner of LCD displays " " icon, then press key to enter into function menu. 2. Press key to choose NO.05 function item, it shows "2T-ENC" on LCD. 3.
  • Page 41: Squelch Mode Setup

    FUNCTION MENU SETUP 5TONE/2TONE: Current optional signaling is 5TONE/2TONE. OFF: Close optional signaling. 4. Press key or key to confirm and exit. Squelch mode setup This function is used for setting squelch mode to prevent receiving unrelated singals. 1. Press key, the top left corner of LCD displays "...
  • Page 42: Frequency Step Size Setup

    FUNCTION MENU SETUP 4. Press key or key to confirm and exit. Frequency step size setup 1. Press key, the top left corner of LCD displays " " icon, then press key enter into function menu. 2. Press key to choose NO. 08 function item, it shows "STEP" on LCD. 3.
  • Page 43: Frequency Reverse

    FUNCTION MENU SETUP Frequency Reverse 1. Press key, the top left corner of LCD displays " " icon, then press key enter into function menu. 2. Press key to choose NO.10 function item, it shows "REV" on LCD. 3. Rotate channel switch to choose desired setup. ON: Turn on Frequency reverse function, TX and RX frequency of current channel will be interchanged.
  • Page 44: Offset Frequency Setup

    FUNCTION MENU SETUP Offset Frequency setup This function works through repeater. When repeater receives signals at one frequency, it transmits at the other frequency. The offset between these two frequencies is called offset frequency. 1. Press key, the top left corner of LCD displays " "...
  • Page 45: Tx Off

    FUNCTION MENU SETUP operating in same frequency. If you press PTT, the radio will beep as warning and get back to receiving state. 1. Press key, the top left corner of LCD displays " " icon, then press key enter into function menu.
  • Page 46: Band Limit

    FUNCTION MENU SETUP Band Limit When this function is on, inputting frequency or Scanning frequency under VFO is limited in current VFO frequency band. 1. Press key, the top left corner of LCD displays " " icon, then press key enter into function menu.
  • Page 47: Keypad Voice Prompt Setup

    FUNCTION MENU SETUP Keypad Voice Prompt Setup 1. Press key, the top left corner of LCD displays " " icon, then press key enter into function menu. 2. Press key to choose NO.18 function item, it shows "BEEP" on LCD. 3.
  • Page 48: Voice Operated Transmission (Vox) Setup

    FUNCTION MENU SETUP Voice Operated Transmission (VOX) Setup When this function is on, the transmitting can be started by voice, no need to press [PTT] key. 1. Press key, the top left corner of LCD displays " " icon, then press key enter into function menu.
  • Page 49: Automatic Power Off Time Setup

    FUNCTION MENU SETUP Automatic Power Off Time setup When this function is on, transceiver will automatic power off when reach the preset time. 1. Press key, the top left corner of LCD displays " " icon, then press key enter into function menu.
  • Page 50: Squelch Level Setup

    FUNCTION MENU SETUP Squelch level setup This function is used for setup intensity of receiving signals, transceiver will hear calls when receiving signal intensity achieve preset data, otherwise, transceiver will keep mute. 1. Press key, the top left corner of LCD displays " "...
  • Page 51: Function Icon Stay Time Setup

    FUNCTION MENU SETUP Function Icon Stay Time Setup 1. Press key, the top left corner of LCD displays " " icon, then press key enter into function menu. 2. Press key to choose NO. 26 function item, it shows "FTIME" on LCD. 3.
  • Page 52: Lcd Backlight Color Setup

    FUNCTION MENU SETUP OFF: Always off. ON: Always on. 4. Press key or key to confirm and exit. LCD Backlight Color Setup There are three kinds of backlight color for optional. 1. Press key, the top left corner of LCD displays " "...
  • Page 53: Tone Pulse Frequency Selection

    FUNCTION MENU SETUP 4. Press key or key to confirm and exit. NOTE: When current channel add 5TONE to be optional signaling, LCD displays 5TONE self ID code, otherwise displays DTMF self ID code. Tone Pulse Frequency Selection This function is used for waking up sleeping repeater, it needs a certain intensity of Tone Pulse to wake up sleeping repeater.
  • Page 54: Fm Radio

    FUNCTION MENU SETUP 1:2: The standby time between normal working state and battery saving mode is 1:2 1:3: The standby time between normal working state and battery saving mode is 1:3 1:5: The standby time between normal working state and battery saving mode is 1:5 1:8: The standby time between normal working state and battery saving mode is 1:8 AUTO: Battery save ratio is adjusting automatically.
  • Page 55: Pf1 Key Function Setup

    FUNCTION MENU SETUP reception. Also when FM Radio is on, quick press of key will mute / un-mute FM Radio. 2. FM Radio activates in either VFO Mode and Channel Mode. In Channel Mode, LCD shows received frequency with saved channel number to right hand side. In VFO Mode, only received frequency will show.
  • Page 56: Senior Function Operations

    SENIOR FUNCTION OPERATIONS Display Mode Setup There are three kinds of display modes for optional. 1. Press [PF2] key to turn on radio, hold [PF2] key until transceiver emits beep. 2. Press key to choose No.01 function item, it shows "DSP" on LCD. 3.
  • Page 57: Cloning Cable

    SENIOR FUNCTION OPERATIONS OFF: No operations. FACT: Resume all items to factory default, including channel and background settings. INIT: Resume background settings to factory default, channel operations are keeping. 4. Press key to exit current selection. 5. Press key to confirm current selection. Cloning Cable This feature will copy the programmed data and parameters from the master unit to slave units.
  • Page 58 SENIOR FUNCTION OPERATIONS [Settings: Master side] 1. Press the [PF1] side key to Power on, the display shows "CLONE", the master unit enters into copy mode . 2. Press [PF1] key, the display appears "CLONE XX" XX stands for the data amount being cloned.
  • Page 59: Memory Bank

    MEMORY BANK 10 memory banks 0-9 are available for 3318UV, bank 0 includes all edited channels. Bank 1-9 can be assigned maximum 32channels, a channel can be assigned to more groups by software programming or radio itself operation. Assign channel to memory bank: 1.
  • Page 60: Bank Linking

    MEMORY BANK Bank linking 1. In channel mode, press key twice to enter into memory bank mode, press key then press key to enter into function menu. 2. Press key to choose menu 34, LCD show "BALK". ON: Turn on Bank linking. The following menus allow adding or deleting banks.
  • Page 61: Programming Software Starting (Takes Windows Xp System For Example)

    Programming software starting (Takes Windows XP system for example) 1.Double Click "QPS3318UV_USA setup.exe", then go on installing as computer command. 2.Click "START" menu of computer, choose "USB To COM" in QPS3318UV_ USA item and click it. Please install USB To Comport drive program as computer command.
  • Page 62: Technical Specification

    TECHNICAL SPECIFICATION General Receiving Part Wide band Narrow band VHF: 136~174MHz (EX: 108~180MHz) Frequency Range UHF: 400~480MHZ (EX:400~520MHz) Sensitivity ≤0.25μV ≤0.35μV (12dB SINAD) Channel Capacity 200 channels Adjacent Channel 25KHz (wide band) ≥65dB ≥60dB Channel Spacing 12.5KHz (narrow band) Selecitvity Intermodulation ≥60dB ≥60dB...
  • Page 63: Trouble Shooting Guide

    TROUBLE SHOOTING GUIDE Problem Corrective Action A.The battery may be exhausting. Recharge or replace the battery. B.The battery may not be installed correctly. Remove the battery No power and install it again. C.The power switch is broken; send it to local dealers to repair. D.Battery touch is broken;...
  • Page 64 TROUBLE SHOOTING GUIDE Can not power on or frequent Check weather the battery touch is out of sharp or broken. power off The receiving sound gets low or Check weather the MIC is stoppage. Otherwise, please contact with intermittent local dealers to repair it. A.Out of communication range or obstruct by tall buildings or in big Receiving intermittent with in big noise.
  • Page 65: Attached Chart

    ATTACHED CHART CTCSS Frequency Chart 62.5 94.8 136.5 177.3 218.1 67.0 97.4 141.3 179.9 225.7 69.3 100.0 146.2 183.5 229.1 71.9 103.5 151.4 186.2 233.6 74.4 107.2 156.7 189.9 241.8 77.0 110.9 159.8 192.8 250.3 79.7 114.8 162.2 196.6 254.1 82.5 118.8 165.5...
  • Page 66: 1024 Groups Dcs Frequency Chart

    ATTACHED CHART 1024 groups DCS frequency chart...
  • Page 67 ATTACHED CHART...
  • Page 68 ATTACHED CHART NOTE: N stands for positive code. I stands for inverted code. 1024 groups of DCS in total.

Table of Contents