Page 2
When programming the transceiver, read the factory initial data firstly, then rewrite the frequency and signaling etc., otherwise errors may occur because of different frequency band etc.. NOTE Models Apply To This Manual: AT888 Mobile radio 888 Mobile Radio Applicable Software: QPS888...
Page 3
If an abnormal odor or smoke is detected coming from the transceiver, turn OFF the power immediately. Contact an Anytone service station or your dealer. Do not transmit with high output power for extended periods; the...
Supplied Accessories Supplied Accessories After carefully unpacking the transceiver, identify the items listed in the table below. We suggest you keep the box and packaging. Transceiver Microphone DC Power Cable with User Manual Fuse Holder(QPL-01)
Initial Installation Determine the appropriate angle of the transceiver, using the 3 screw Mobile installation hole positions on the side of the mounting bracket. To install the transceiver, select a safe, convenient location inside your vehicle that minimizes danger to your passengers and yourself while the vehicle is in motion.
Page 7
Initial Installation Connect the DC power cable to the regulated DC power supply and ensure that the polarities are correct. (Red: positive, Black: negative). Do not directly connect the transceiver to an AC outlet. Black Use the supplied DC power cable to connect the transceiver to a regulated power supply.
Initial Installation The possible locations of antenna on a car are shown as following: Fuse Location Fuse Current Rating Transceiver Accessories Connections Supplied Accessory DC External Speaker power cable If you plan to use an external speaker, choose a speaker with an Only use fuses of the specified type and rating, otherwise the transceiver impedance of 8Ω.
Page 9
Initial Installation Microphone For voice communications, connect a microphone equipped with an 8-pin modular plug into the modular socket on the front of the main unit. Press firmly on the plug until the locking tab clicks. Attach the supplied microphone hanger in an appropriate location using the screws included in the screw set.
Getting Acquainted FRONT PANEL REAR PANEL FUNCTION repeating connection Connecting by repeater cable to another • Basic Function port QX888 and realize repeating function. NO KEY FUNCTION Ext speaker Terminal Terminal for optional external speaker SP01. Press this key turn on or turn off the Power transceiver.
Getting Acquainted Microphone MIC Connector Diagram(in the front view of connector) decrease increase channel key channel key Key Pad Serial Data transmit key DOWN Built in MIC GND Mic connecting microphone line/ Crystal plug MIC connecting line...
Basic Operations Switching The Power On There are two groups of this transceiver, and every group has 100 channels, when one group UP adjust or Down adjust to PWR KEY In power off state, press key, last or first channel, then UP or DOWN adjust again, the channel until the transceiver sounds "...
Basic Operations The speaker is built in microphone, only connect microphone to hear someone talking. When the transceiver RX indicator light up, but can not hearing transmit party calling, it refers current channel receive match carrier but different signal. TRANSMITING PILOT FREQUENCY In standby state, press PTT key then pres [DN] key to transmit pilot frequency.
Programming Software Installing and Starting (in windows XP system) Double click "QPS888 setup.exe", then follow the installing instruction. Install USB Cable Driver Programme (As pic 1) Click start menu in computer, under "ALL PROGRAMS" menu, choose and click "USB To Com port" in QPS888 program, install "USB To Com port"...
Maintenance Trouble Shooting Default Setting after Resetting(UHF) Problem Possible Causes and Potential Solutions DCS encode + and - polarities of power connection and decode (a) Power is on, nothing are reversed. Connect red lead to plus UFO frequency 435.00MHz DCS code 023N appears on Display.
Page 19
SAFETYTRAININGINFORMATION Your radio generators RF electromagnetic energy during Qixiang Electron Science & Technology Co.,Ltd. transmit mode.This radio is designed for and classified as“Occupational Use Only”,meaning it must be used only during the course of employment by individuals aware of the hazards,and the ways To Minimize Such hazards. This radio is NOT intended for use by the“General Population” in an uncontrolled environment. This radio has been tested and complies with the FCC RF exposure limits for“Occupational Use Only”.Inaddition, your radio complies with Qixiang Electron Science & Technology Co.,Ltd. the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans: � FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields.
Page 20
INFORMATION SAFETY TRAINING RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or an antenna specifically authorized by the WARNING: manufacturer for use with this radio. This radio generates RF electromagnetic energy during transmission. •...
Need help?
Do you have a question about the AT888 and is the answer not in the manual?
Questions and answers