Source Subsystem - Racal Instruments 3155 User Manual

User Manual 3155
SOURce Subsys-
tem
Keyword
Limit
[:SOURce]
:APPLy (?)
:SINusoid (?)
:TRIangle (?)
:SQUare (?)
:PULSe (?)
:RAMP (?)
:SINC (?)
:EXPonential (?)
:GAUSsian (?)
:DC (?)
:USER (?)
:FM (?)
:DEViation (?)
:FUNCtion
:MODE (?)
:SHAPe (?)
:FREQuency
:RASTer (?)
:TRIGger
:MODE (?)
:SLOPe (?)
:FREQuency (?)
:RASTer (?)
:FSK (?)
:FREQuency
:RASTer (?)
:MODE (?)
:RAMP
:TIME (?)
:FUNCTion
:MODE (?)
:SHAPe (?)
:ROCSillator
:SOURce (?)
:SWEep (?)
:STOP (?)
:TIME (?)
:DIRection (?)
:SPACing (?)
:TRIGger
:MODE (?)
:SLOPe (?)
This subsystem is used to control output functions, shape and p a-
rameters, frequency, amplitude and amplitude modulation, and filter
type. Optional nodes were omitted from these commands. Factory
defaults after *RST are shown in bold typeface. Parameter low and
high limits are given where applicable.
Parameter Form
{<freq>,<ampl>,<offs>,<phase>}
{<freq>,<ampl>,<offs>,<phase>}
{<freq>,<ampl>,<offs>,<duty_cycle>}
{<freq>,<ampl>,<offs>,<delay>,<rise>,<high>,<fall>}
{<freq>,<ampl>,<offs>,<delay>,<rise>,<fall>}
{<freq>,<ampl>,<offs>,<N_cycles>}
{<freq>,<ampl>,<offs>,<exp>}
{<freq>,<ampl>,<offs>,<exp>}
<%_ampl>
{<seg#>,<sclk>,<ampl>,<offs>}
{OFF|ON|0|1}
<deviation>
{FIXed|USER}
{SINusoid|TRIangle|SQUare|RAMP)
<FM_freq>
<FM_sclk>
{CONTinuous|TRIGgered|GATed}
{POSitive|NEGative
{<freq>|MINimum|MAXimum}
{<sclk>|MINimum|MAXimum}
OFF|ON|0|1}
<FSK_sclk>
{HOP|RAMP}
<time>
{FIXed|USER|SEQuence}
{SINusoid|TRIangle|SQUare|PULSe|RAMP
|SINC|EXPonential|GAUSsian|NOISe|DC}SINusoid
(INTernal|EXTernal | TCXO)
OFF|ON|0|1}
<stop_sclk>
<time>
(UP|DONW)
(LINear|LOGarithmic)
{CONTinuous|TRIGgered|GATed}
{POSitive|NEGative
Default,Low
OFF
1e6,100e-3,100e6
FIXed
SINusoid
1e3,1e-3,100e3
1e6,1e-3,2e6
CONTinuous
POSitive
1e6,100e-6,50e6
10e6,100e-3,100e6
OFF
80e6,100e-3,100e6
HOP
1e-3,10e-6,1
FIXed
INTernal
OFF
20e6,100e-3,100e6
1e-3,1e-3,1000
UP
LINear
CONTinuous
POSitive
Programming Reference 4-23
Limit,High