Page 1 Xerox DocuPrint 180 Laser Printing System Message Guide April 1998 721P85550...
Page 2 Printed in the United States of America. Publication number: 721P85550 Xerox® and all Xerox products mentioned in this publication are trademarks of Xerox Corporation. Products and trademarks of other companies are also acknowledged.
Page 3: Related Publications
Related publications The Xerox DocuPrint 180 Laser Printing System Message Guide is part of the ten manual reference set for your laser printing system. The entire reference set is listed in the table below. Several other related documents are also listed for your convenience. For a...
Page 4 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 5: Table Of Contents
Table of Contents Related publications Notice Introduction About the reference set Xerox DocuPrint 180 Laser Printing System document set What the message guide contains How the message guide is organized The conventions used in this guide 1. CP (COMPRESS command) messages 2.
Page 6 15. Xerox DocuPrint 180 LPS additional messages 15-1 Numbered Xerox DocuPrint 180 LPS messages 15-3 A. Xerox support services Xerox Customer Support Center Xerox Customer Service Support Center Xerox Font Center Glossary GLOSSARY-1 XEROX DOCUPRINT 180 LASER PRINTING SYSTEM MESSAGE GUIDE...
Page 7: About The Reference Set
Introduction The Xerox DocuPrint 180 Laser Printing Systems Message Guide is one of the ten manuals which make up your Xerox DocuPrint 180 Laser Printing System (LPS) Reference Set. The LPS Message Guide provides an easy to use reference tool for...
Page 8 This reference provides a quick reference of commonly-used Command Summary Card commands. Xerox DocuPrint 180 LPS Message This reference contains the following information: Guide • OSS and other messages • Meaning and recovery procedures viii XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 9 Tasks that must be accomplished before installation • Preinstallation requirements • Installation process • Postinstallation activities Xerox DocuPrint 180 LPS PC UI This reference contains the following information: Reference • PC UI procedures • Hierarchy of PC UI windows Xerox DocuPrint 180 LPS Product...
Page 10: Cp (Compress Command) Messages
INTRODUCTION What the message guide contains The Xerox DocuPrint 180 LPS Message Guide is divided into the following chapters: Chapter 1: CP (COMPRESS command) messages Chapter 2: DSR (disk save and restore command) messages Chapter 3: FD (forms compilation) messages...
Page 11 Fewer than 25 sheets of paper remain in (feeder) tray 1. This column also lists the action(s) to take, if any, in response to the message. For example: 1. Add paper to (feeder) tray 1. 2. Press the <CON> key to resume printing. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 12 <ENTER> or <RETURN> key. restart job = Send or transmit a job again (online) or rewind a tape and start job again (offline). recode job = Rewrite the JSL entry or DJDE, making necessary changes. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 13 1CP (COMPRESS command) messages These messages may appear during the process of compressing the system disk. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on managing LPS resources for additional information.) CP1010 Compress now restoring the print file The COMPRESS command was entered.
Page 14 COMPRESS task. Action Perform DSR, selecting compressed object mode, to compress the disk. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on managing LPS resources for additional information.) CP9100 File integrity error. Edit and print CPR000.TMP The system has discovered a multi-allocated sector and is listing it in a special file (CPR000.TMP).
Page 15: Dsr (Disk Save And Restore Command) Messages
These messages may appear during the process of saving all disk files on tape or restoring all files to system disk from tape. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on managing LPS resources for additional information.)
Page 16 DSR task is aborted. Action 1. Clean the tape drive and retry the task. (Refer to the maintenance chapter in your Xerox DocuPrint 180 LPS Operator Guide. ) 2. If the problem continues, replace the save tape.
Page 17 DS9050 File structure integrity error on xx...DSR aborted The specified disk drive has a corrupt file structure. A format will be required. Reformat the system disk. (Refer to your Xerox DocuPrint 180 LPS Action Operations Reference .) DS9060 Invalid DSR.SAF detected DSR.SAF is corrupt or incompatible with DSR.
Page 18 DSR (DISK SAVE AND RESTORE COMMAND) MESSAGES XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 19 Unrecognized key-in, key-in ignored. May be reentered A command was entered incorrectly or placed incorrectly in a line. The system is ignoring the entry. Action Reenter the command correctly. (Refer to your Xerox DocuPrint 180 LPS Forms Creation Guide .) FD2710 Invalid character, reenter The symbol or word entered was incorrect for its location in the command line.
Page 20: Fd (Forms Compilation) Messages
The compiler will abort. Action 1. Check FSL for the correct file name. 2. Create the FSL file on disk if necessary. (Refer to your Xerox DocuPrint 180 LPS Forms Creation Guide .) 3. Retry the FDL task.
Page 21 Forms Compiler will abort. Action 1. Retry the entry. The message should not reappear if the failure was an intermittent memory error. 2. If the problem continues, contact your systems specialist or Xerox Customer Service. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 22 FD (FORMS COMPILATION) MESSAGES XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 23 (HIP). The HIP chapters in your Xerox DocuPrint 180 LPS Operator Guide and Xerox DocuPrint 180 LPS Operations Reference provide detailed information on HIP. Note: Only XPS and XPF are applicable when looking at these messages.
Page 24: Hip (Host Interface Processor) Messages
Action None. HP0130 Log file reset You have entered HIP LOG [RESET]. The system is informing you that the log file has been cleared and all information had been deleted. Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 25 All job information appears on the system (controller) display. No more related information will appear at this time. Action None. HP1120 HIP job queue cleared No data remains in the HIP buffer; jobs have printed or have been aborted. Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 26 Action 1. Delete unneeded files from system disk to create more space. 2. Compress the disk. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on managing LPS resources for additional information.) 3. Enter SETUP mode to change the HIP buffer file size. (Refer to...
Page 27 This is an informational message stating the HIP version(s) being used. Action None. HP1200 Offline pending end of transmission The HIP OFFLINE command was entered. The printer will go offline when the current file being received is complete. Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 28 (This message is displayed every 30 seconds until the host comes online or the interface is terminated.) Action 1. If using XPAF, contact your systems specialist or Xerox Customer Service. 2. If the failure recurs, call for service.
Page 29 (saved at system error restart) and written to system disk. The system then reestablishes the communications link and continues to receive the next block of data. Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 30 Action 1. Log off and then log on at level 2. 2. Refer to the appropriate Xerox DocuPrint 180 LPS Operator Guide . HP1330 Buffersize=xxx, utilization=yy% zzzz blocks used, uuuu blocks available.
Page 31 Action None. HP2010 No host selected A host has not been selected for HIP. Enter the appropriate HIPHOST command. (Refer to your Xerox Action DocuPrint 180 LPS Operations Reference chapter on HIP-accessed communicating modes for additional information.) HP2020 Selected host not present on system The host selected is not available on your system.
Page 32 Action 1. Delete files from system disk to provide more space. 2. Compress the system disk. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on managing LPS resources for additional information.) 3. Enter the SETUP mode to change the HIP buffer file size.
Page 33 Wait until jobs have printed, then reenter the HIP SEND request. HP2290 Pass-through pending, enter ‘HIP START.’ Pass-through pending, select or enter ’HIP START.’ A pass-through job has been sent from the XPAF host; HIP must be started. Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 4-11...
Page 34 Invalid command with no host specified A host must be selected before the command can be carried out. Action 1. Select a host. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on HIP-accessed communicating modes for additional information.) 2.
Page 35 2. Enter the ABORT job command to cancel the job (if only one remains). 3. Enter the RESET command to delete all jobs. 4. Reenter the HIP DIAGNOSTIC command to proceed with diagnostics. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 4-13...
Page 36 2. Wait until active and pending jobs have been printed. HP8100 HIP dynamic memory allocation failure: reload HIP does not have enough memory to continue. Action 1. Enter the HIP END command. 2. Restart HIP or reboot the system. 4-14 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 37 Fatal protocol violation detected Commands used violate the higher-level software protocols used to communicate between the Xerox DocuPrint 180 LPS and the host. The host will be advised to restart communication with the printer. No data should be lost in this process.
Page 38 HIP diagnostic failed. Action 1. Reenter the HIP DIAGNOSTIC command to retry the diagnostic test. 2. If the problem recurs, contact your systems specialist or Xerox Customer Service. HP9431 Line no. n is open The HIP DIAGNOSTIC command was entered. The system failed Test 3 which verifies integrity of 8 parallel data lines.
Page 39 5IFU (Interpress font utility) messages These messages appear when the Interpress font utility program (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on HIP-accessed communicating modes for additional information.) The meaning of terms used in this section can be found in the Glossary at the back of the message guide.
Page 40: Ifu (Interpress Font Utility) Messages
Could not find the font file xxxx to delete it This warning is given when an attempt is made to delete a particular font file that does not exist on the system. Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 41 The requested rendered character requires RIP (raster image processor), which is not on your system. Action None. IF1502 Adding as composite bitmap The requested character is being added as a composite bitmap. Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 42 This message provides font mapping that is currently being inserted into the Interpress font mapping structure. Action None. IF1628 Floppy is not supported The optional floppy drive is not supported as an IFU input device. Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 43 Font mask is invalid In the READ or WRITE statement, the font name mask (complete font family name) has an invalid parameter. Action Reenter the command, using valid parameters in the READ or WRITE statement. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 44 Invalid number of files have been specified to move An incorrect number of files to be moved has been given. Action Check the number of items on the medium, and enter a valid number of files to move. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 45 An IFU COPY label is not present to allow processing to begin. Action 1. Reposition medium at start of volume if it is the correct medium mount the correct volume. 2. Retry the command. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 46 Action 1. Mount the correct tape Initialize the medium via the IFU VOLINIT command if the data on the tape is not needed. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on managing LPS resources for additional information.) 2.
Page 47 IFU COPY command, it may not be ready to be mounted yet, or it may be faulty. Action Retry mounting the same floppy disk or a different one. Reboot the system and reenter the command. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 48 Interpress fonts stored on the system may not be listed. Action Retry the operation by entering a number of IFU LIST commands with specific parameters. This will allow the system to list all Interpress fonts within each parameter. 5-10 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 49 FTYPE = EXTENDED and retry the ADD process. If your system does not have the 5-word FST format, decrease the number of characters requested in the CHARS/DCCHARS parameter in the font profile and retry the ADD process. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 5-11...
Page 50 3. If the message reappears, contact your systems specialist or Xerox Customer Support. IF2332 Composite request (character x) requires RIP The composite character requested in the font profile requires RIP (raster image processor), which is not on your system. Action None. 5-12 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 51 The IPFONTS statement in the font profile does not contain the CHARS (enumeration or range of point sizes) parameter. Action 1. Enter the CHARS parameter in the IPFONTS statement of the font profile. 2. Reenter the ADD command. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 5-13...
Page 52 1. Compile the correct IPFNTS.JSL with the needed mapping structure. 2. Retry the ADD command. IF2426 Point size x was not found in easy values The point size requested is not contained within the FIS font master. Action None. 5-14 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 53 Too many embedded blanks within family name There are too many spaces in the family name parameter of the command line. Action Reenter the family name parameter of the command sequence to include an acceptable number of spaces. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 5-15...
Page 54 (parameter) in the command sequence. Action Reenter the command to include at least one more parameter. IF2707 Syntax error: unexpected punctuation Incorrect punctuation is present in the command line. Action Reenter the command using acceptable punctuation. 5-16 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 55 Syntax error: invalid command x has been encountered The command requested is not allowed. Action 1. Verify and reenter the command. 2. If the message reappears, contact your systems specialist or Xerox Customer Support. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 5-17...
Page 56 2. If the message reappears, contact your systems specialist or Xerox Customer Support. IF2851 Invalid default font name The default substitution font requested is incorrect. Action Check and reenter the DEFAULT statement using an acceptable font name. 5-18 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 57 The resolution requested (300 or 600 spi) in the fonts statement in the JSL file is incorrect for your system’s configuration. Action 1. Correct the resolution parameter in the FONTS statement in the JSL file. 2. Retry the command. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 5-19...
Page 58 JSL syntax err x - invalid hex value An incorrect hexadecimal value exists in the JSL file. Action 1. Correct the JSL file to include a correct hex value. 2. Retry the command. 5-20 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 59 2. Retry the command. IF2909 JSL syntax err x - missing a semi-colon A semi-colon is missing from the JSL file. Action 1. Correct the JSL file to include the missing semi-colon. 2. Retry the command. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 5-21...
Page 60 One or more subcharacter component(s) of a rendered character has not been specified within the font profile. Action 1. Add the appropriate character(s) to the font profile CHARS statement. 2. Reenter the ADD command. 5-22 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 61 2. Reenter the ADD command. IF2972 Bad COMPOSITES parameter. The COMPOSITES parameter in the font profile contains incorrect syntax. Action 1. Correct the syntax of the COMPOSITES parameter in the font profile. 2. Reenter the ADD command XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 5-23...
Page 62 None. IF4110 FIS master error; aborting ADD Due to an error in the FIS master, the requested ADD command is being aborted. Action 1. Obtain a valid FIS master. 2. Retry the command. 5-24 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 63 This error is probably the result of a previous error which should have displayed a message. Action Contact your systems specialist or Xerox Customer Service. IF4112 Unable to create a font file, x; aborting ADD. An error has occurred when the system attempted to access the font file.
Page 64 IF7100 Can‘t find IFUFSN.SYS; resysgen and retry ADD The IFUFSN.SYS file, which contains default font information, was not found on the system disk. (Refer to your Xerox DocuPrint 180 LPS System Generation Guide .) Action 1. If authorized to do so, resysgen.
Page 65 Xerox Customer Service. IF7704 Family name directory is out of space There is no more space in the FDR file. This is a software limitation problem. Action Contact your systems specialist or Xerox Customer Service. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 5-27...
Page 66 IF7800 Interpress decomposer initialization error There is insufficient memory to initialize IPD. Action Contact your systems specialist or Xerox Customer Service. IF7801 Interpress mapping file package ADD function failed An error occurred when adding an entry to the IPM (Interpress.
Page 67 3. If the problem continues, contact your systems specialist or Xerox Customer Service. IF7908 MAPM of font request memory failed The request for mapping memory failed due to insufficient available memory. Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 5-29...
Page 68 SAMPLE command, does not exist because the FOPEN command failed. This is a probable disk error. Action Contact your systems specialist or Xerox Customer Service. IF7910 IPM FDR routine x has failed An error occurred while accessing the file directory (FDR), probably due to a disk error.
Page 69 IF8101 CMT calling sequence error x The character mapping table is being processed out of sequence. Action Contact your systems specialist or Xerox Customer Service. IF8102 CMT storage request has failed The amount of storage space requested is too large.
Page 70 There was not enough space in the character mapping table when adding the next symbol. Action Contact your systems specialist or Xerox Customer Service. IF8104 CMT entry table has overflowed by map x There was not enough space in the character mapping table when adding the next entry.
Page 71 IF8205 Error: from IPM_set_family_mask ( ) The IPM file is being processed out of sequence. Action Contact your systems specialist or Xerox Customer Support. IF8207 Error: from IPM_set_font_mask ( ) The IPM file is being processed out of sequence. Action Contact your systems specialist or Xerox Customer Support.
Page 72 1. Check if the IFUFFM.SYS file is on the system. 2. If IFUFFM.SYS is on the system, it is corrupted and should be deleted. 3. Retry the ADD command. 4. If the problem continues, contact your systems specialist or Xerox Customer Service. 5-34 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 73 1. Check if the IFUDLM.SYS file is on the system. 2. If IFUDLM.SYS is on the system, it is corrupted and should be deleted. 3. Retry the ADD command. 4. If the problem continues, contact your systems specialist or Xerox Customer Service. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 5-35...
Page 74 IPM calling sequence error x The IPM file is being processed out of sequence. Action Contact your systems specialist or Xerox Customer Service. IF8302 IPM disk family x is too big In an IFU IPFNTS command, this IPM name is too large to be added to the IPM file on the system.
Page 75 The FIS font request cannot be processed due to the EMT (emulator trap) return code shown. Action Contact your systems specialist or Xerox Customer Service. IF8402 FIS initiation failed with EMT return code x Initiation of FIS cannot be processed due to the EMT return code shown.
Page 76 Internal buffer allocation failed, aborting ADD. Memory allocation for a font file has failed. Action Contact your systems specialist or Xerox Customer Service. IF8500 Decomposed FIS file has bad syntax. An error occurred while the system was processing an internal temporary file.
Page 77 Action 1. Select the abort option when the display prompts you to choose retry, ignore, or abort. 2. Contact your systems specialist or Xerox Customer Service. IF9007 **- TAPE UNIT IS offline-** The magnetic or cartridge tape is not online.
Page 78 An attempt to read from the IPM file has failed, probably due to a disk error. Action 1. Delete the IPM files from your system. 2. Recompile the IPFNTS.JSL file to recreate the IPM files. 3. Retry the command. 5-40 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 79: Oss (Operating System Software) Messages
The first digit after “OS” indicates the message level. For example, OS7210 is a Level 7 message. Your Xerox DocuPrint 180 LPS Operator Guide and Xerox DocuPrint 180 LPS Operations Reference provide detailed information about LPS operations and related messages.
Page 80 Action None. OS0310 Bin x selected One of the following commands was entered: -SELECT -SELECT 1 -SELECT AUTO -SELECT 1,SAMPLE Output will be delivered to stacker bin x. Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 81 OS0500 Output stopped The STOP or STOP O command was entered or the <STOP> key was pressed. Printing has stopped. (Input continues.) Action To restart: Enter CONTINUE or CONTINUE O Press the <CON> key. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 82 CLUSTER n or CLP n was entered, but the specified feeder tray was not found in any cluster. Action Check the cluster and assign a valid feeder tray. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on setting up print jobs for additional information.)
Page 83 Note: This message may appear numerous times during the FEX session. Action None. OS0800 NVM update in progress ****DO NOT DISTURB**** The periodic acquisition of information from the printer control console is in progress. Action Do not disturb. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 84 PQA operation and may accompany other related messages. Action None. OS0852 Cluster: xxxxx Output tray: n This message identifies the cluster name and output tray number involved in the current PQA operation and may accompany other related messages. Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 85 Substituting color for all colors for this report After you enter a SUBSTITUTE INK command, this message tells you the primary color which is being substituted for all non-black primary colors in your report. Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 86 Substituting color for color for all jobs After you enter a SUBSTITUTE INK command, this message tells you which primary color is being substituted for the specified primary color(s) in all of your jobs. Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 87 The ABORT or @ABORT command was entered. The nonprint task has been discontinued. Action None. OS0990 Resetting the system The RESET command was entered. All jobs in the print queue are being deleted. Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 88: Os Level 1: Information
OS1005 Sample not allowed while Sample Tray is selected Intermixing sample sheets with the job output in the sample tray would cause integrity errors. Sample is not allowed at this time. Action None. 6-10 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 89 Printer is not available; Printer is being serviced The printer is unable to respond to the entered command because the Xerox service representative is performing diagnostic tests. The printer control console displays one of the following messages for use of the service representative only:...
Page 90 Check command and retry. Action None. OS1016 NT01 or staple not supported Xerox DocuPrint 180 LPS does not support Staple. If Staple is specified in a JDE, JDL or DJDE, then INPUT will ignore it. Action None. 6-12 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 91 Action None. OS1073 Data1 = nn, Data2 = nn, Data3 = nn, Data4 = nn This message is for diagnostic purposes only. Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 6-13...
Page 92 Action None. OS1096 Activity report ending Processing of the Activity Report has completed. No action. Action None. OS1097 User report ending Processing of the User Report has completed. No action. Action None. 6-14 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 93 If authorized to do so, resysgen the system, entering the serial number (located on a panel inside the printer) when instructions on the display ask for it. (Refer to Xerox DocuPrint 180 LPS System Generation Guide , or contact your systems specialist.)
Page 94 (‘0’) of sheets for your FEX test print job. Action None. OS1150 Job queue full Print queue cannot hold any more data. Action Print or delete jobs in queue before more jobs are sent. 6-16 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 95 An online only command was entered while the system is offline. Action Place the system online to perform the desired function. (Refer to the online chapter in your Xerox DocuPrint 180 LPS Operator Guide . OS1175 Command not allowed while **** is active The command entered cannot be processed while the indicated task is in progress.
Page 96 Action Follow directions appearing at the system controller display to initiate automatic job recovery and abort the analysis dump. (Refer to the offline chapter in your Xerox DocuPrint 180 LPS Operator Guide .) OS1225 Automatic recovery initiated Automatic job recovery has been initiated at the system controller display after a system rollover due to software failure.
Page 97 ACCOUNT or REPORT command that has been entered. Action Obtain the correct password and log on at the correct level. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on setting LPS parameters for additional information.) OS1261 Paper size out of range The paper size specified in the JSL is not supported by the IOT.
Page 98 The command file entered is formatted incorrectly. It appears to be contained (nested) within another command file Action 1. Correct your command file format. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on creating and using command files for additional information.) 2.
Page 99 1. Document circumstances of the message appearance. 2. Record any additional messages displayed in conjunction with 3. Contact your systems specialist or Xerox Customer Service with the above information. Note: Messages OS1280 and OS1282 should not appear. If one of...
Page 100 Action Check your cluster configuration and enter a new command that will allow toggling. (Refer to the chapter on feeder trays in your Xerox DocuPrint 180 LPS Operations Reference .) 6-22 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 101 A command was entered that is invalid for the printer‘s stacker tray configuration. Action Reenter the command, using a stacker bin that your system has. (Refer to the output tray or bin chapter in your Xerox DocuPrint 180 LPS Operator Guide .) OS1296 There is no stockset specified at this time...
Page 102 If you enter the ATTENTION LIGHT command with no new parameters, the message provides the current settings. Action None. 6-24 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 103 If you enter the ATTENTION ALARM ENABLE command, the message tells you that the value you requested is accepted or provides the current setting if you have not included the parameter with the command. Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 6-25...
Page 104 The alignment number entered for dots or lines is not within the permitted range. Action Reenter the ALIGN command with value(s) within the range. (Refer to the problem solving chapter in your Xerox DocuPrint 180 LPS Operator Guide .) OS1391 Invalid Scan or Dot value. Retry DAlign For Xerox service personnel, this messages indicates that incorrect alignment values have been entered.
Page 105 1. Retry the SAMPLE command, ensuring that you are requesting a font that may be sampled. 2. If the message reappears, contact your systems specialist or the Xerox Font Center for assistance with replacing the font. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 6-27...
Page 106 Cannot space reports before Start command The SPACE n REPORTS command was entered. The system cannot space over reports because START command was not entered. Action 1. Enter the START command. 2. Reenter the SPACE command. 6-28 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 107 The SPACE -n PAGES command was entered. The system cannot space backward any more pages because it is printing the last or only copy of a report. (Pages were cleared from system disk immediately after printing.) Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 6-29...
Page 108 One of the following commands was entered: MOVE n BLOCKS MOVE n FILES SPACE n PAGES SPACE n REPORTS The system cannot space or move forward over any more text because no more data has been input. Action None. 6-30 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 109 Inappropriate disk file type specified An incorrect disk file type has been entered. Action Check the file type and reenter it correctly. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on managing LPS resources for additional information.) OS1552 File does not exist The file name entered has not been input or stored on system disk.
Page 110 File ‘nn.nn’ replaceddata loss...enter ‘Continue’ or ‘Abort’ The file indicated has been replaced on the system disk by a file with the same name that was sent from the host. (This message appears if file being sent is in the Xerox label format.) Action None.
Page 111 The system cannot print dump because the file is protected by the SECURE filename.filetype command. Action 1. Obtain the correct password and log on at Level 5. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on setting LPS parameters for additional information.) 2. Retry printout. OS1600...
Page 112 This system is not configured for this command. You have entered a 4850 3.7 color command such as SUBSTITUTE INKS, PGA, or LIGHT or another printer. DCU is informing you that this cannot be done. Action None. 6-34 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 113 The magnetic tape drive has been selected. Action None. OS1761 Cartridge tape unit selected The 180 CTS has been selected. Action None. OS1765 Tape unit x selected The tape unit indicated in the message has been selected. Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 6-35...
Page 114 OS1781 “ONLINE” JDE/JDL Host and device type mismatch The JDE/JDL in effect is incorrect or contains unsupported options. Action Recode JDE/JDL. (Refer to your Xerox DocuPrint 180 LPS PDL Reference .) OS1800 Input processing aborting The ABORT I command was entered. The input processing task is stopped, and no more data is being sent.
Page 115 The system is not configured for the requested duplex diagnostic print job. The system diagnostics interface (SDI) operation has been aborted. An invalid diagnostic print request has been generated. Action Respective as simplex and retry. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 6-37...
Page 116 The ENDJOB command was entered after printing was completed. The command is being ignored. Action None. OS1910 This function of input not implemented A command was entered relating to an input function not available on your system Action None. 6-38 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 117 Action Retransmit the FCB with channel assignments. (Refer to your Xerox DocuPrint 180 LPS Operations Reference for additional information.) OS1959 Partial set delivered to bin before switch occurred.
Page 118 PQA as current trays in a valid cluster. 2. With the dual stacker you must specify different output trays for PQA and the print job. (Refer to your Xerox DocuPrint 180 LPS Operator Guide, chapter 6, “Running print jobs,” for more information.)
Page 119 A connection between FCG and the LPS printer has failed three times. This message is followed by message OS1976 PROFILE NOT LOADED. FCG EXITING: UNABLE TO Action Contact your supervisor or systems specialist. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 6-41...
Page 120 Performing print quality adjustment. This message informs you that print quality adjustment has started. Action None. OS1981 Print quality adjustment has been completed. This message informs you that print quality adjustment has completed successfully. Action None. 6-42 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 121 No test patterns form available for specified source size No test pattern form file is available for the paper size requested. Action Select a different paper size and retry the command. Abort the operation. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 6-43...
Page 122: Os Level 2: Routine Maintenance
READY TO PRINT--CHECK PAPER SUPPLY IN TRAY 1 Action 1. Add paper to (feeder) tray 1. (Refer to the chapter on feeder trays in your Xerox DocuPrint 180 LPS Operator Guide .) 2. Press the <CON> key to resume printing. OS2003 Check paper supply in Tray 2 Fewer than 25 sheets remain in (feeder) tray 2.
Page 123 WARMING UP--BOTH PAPER TRAYS NOT SET FOR SAME SIZE- -PRESS i Action If tray switching is desired, reset the paper length guides to the same size. (Refer to the chapter on feeder trays in your Xerox DocuPrint 180 LPS Operator Guide.) OS2005 Enter ‘CONTINUE I’ to resume input Select ‘CONTINUE I’...
Page 124 Action 1. Load the magnetic tape reel for the job to be printed if you have not already done so. (Refer to the offline chapter in your Xerox DocuPrint 180 LPS Operator Guide .) 2. Enter the CONTINUE I command to start inputting data from tape.
Page 125 1. Ensure that the current job is backed up the required number of pages so no data is lost. (Refer to the online and offline chapters in your Xerox DocuPrint 180 LPS Operator Guide .) 2. Enter the CONTINUE I command to resume input.
Page 126 PRINTER IS WARMING UP--PAPER TRAY 1 IS EMPTY-- PRESS i Add paper to the main feeder tray. (Refer to the chapter on feeder trays in your Xerox DocuPrint 180 LPS Operator Guide .) PRINTING--PAPER TRAY 1 IS EMPTY. BOTH TRAYS SET FOR _._X_._"...
Page 127 (Refer to the chapter on feeder trays in your Xerox DocuPrint 180 LPS Operator Guide .) 2. Add paper to feeder tray 2. (Refer to the chapter on feeder trays in your Xerox DocuPrint 180 LPS Operator Guide .) 3. Press the <CON> key to resume printing. OS2080 Paper Tray x is empty.
Page 128 Bin x full. The bin indicated in the message is full, thus causing the printer to cycle down or preventing it from cycling up. Action 1. Empty the bin. 2. Restart the job. 6-50 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 129 READY TO PRINT. OUTPUT TRAY 2 IS FULL. Action 1. Empty stacker tray 2. (Refer to the chapter on output trays in your Xerox DocuPrint 180 LPS Operator Guide .) Send output to stacker tray 1 by entering the SELECT 1 command.
Page 130 1. Adjust the length guide and load paper of correct size. (Refer to the chapter on feeder trays in your Xerox DocuPrint 180 LPS Operator Guide. ) 2. Enter the CONTINUE O command, press the Continue button, or press the <CON>...
Page 131 OS2282 Current feed cluster deleted The current FEED cluster has been deleted. The system will default to MAIN. Use the FEED cluster name command to change from the default, if desired. Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 6-53...
Page 132 Press the <CON> key to resume printing and let the FEED command override the DJDE. Enter the FEED MAIN command to let the data stream (DJDE) determine the cluster used. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on setting up print jobs for additional information.) OS2290 Enter ‘RETURN’...
Page 133 An STIMING command has been detected in the datastream. This command is ignored because the printer relies on the operator using FCG to specify finishing-device timing parameters. This message is informational only. Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 6-55...
Page 134 Action Release the feeder belt and check both feeder trays, removing any misfed paper. (Refer to the problem solving chapter in your Xerox DocuPrint 180 LPS Operator Guide . OS2451 Requested bypass not on system. “CONT” defaults to bin. Enter Continue or Abort.
Page 135 OS2560 Please clean the tape drive before next tape mount. Clean the magnetic tape drive before mounting the next tape drive. (Refer to the maintenance chapter in your Xerox DocuPrint 180 LPS Operator Guide .) Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 136 Action Remove tape and mount volume that is next in numerical order. (Refer to your Xerox DocuPrint 180 LPS Tape Formats Manual .) OS2610 Improper ink-name list specification The ink-name list you have specified does not conform to ink-name list syntax.
Page 137 Action 1. Write the current status file to magnetic tape. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on tracking system activity for additional information.) 2. Enter the SFS CLEAR command, then the SFS CREATE command to create a new Status File.
Page 138 Enter Y to create an accounting file for 2000 reports. Enter N to create an accounting file for 100 reports. (Refer to your Xerox DocuPrint 180 LPS System Generation Guide .) 0S2669 Enter ‘PQA Start’ to initiate a Print Quality Adjustment.
Page 139 This command is used in a variety of conditions, usually when the job calls for an ink that has not been defined. There is no operator action, the report will either be aborted or the current dry ink will be substituted automatically. Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 6-61...
Page 140 • The stock you want to use for the print quality adjustment (PQA) is loaded in the paper tray • The target PQA output tray is empty. Action None. 6-62 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 141 2. If the message reappears, the command cannot be used with your system. OS2711 CMD not allowed while diagnostic print job is in progress. You have entered a command that cannot be processed because a diagnostic print job is being run. Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 6-63...
Page 142 This command is no longer supported. See -11 The command entered is obsolete; your system cannot respond. Action 1. Refer to your Xerox DocuPrint 180 LPS OSS Program Description (“-11”) for the correct command for the desired process. 2. If information cannot be located, contact your systems specialist or Xerox Customer Support.
Page 143 Action Reenter the START command with the correct JDE. (Refer to the online chapter in your Xerox DocuPrint 180 LPS Operator Guide .) OS2741 JDL not found. Check and retry. The JDL entered in the START command does not exist on the system disk.
Page 144 If JDE/JDL are different than before the spacing function, enter the CONTINUE command followed by a new JDE and JDL ID (CON “jde,” “jdl”). (Refer to the offline chapter in your Xerox DocuPrint 180 LPS Operator Guide .) OS2810 Start-up message from Job Tape follows: This message appears in a single report mode.
Page 145 Output must be stopped before spacing can be done. The SPACE n PAGES command was entered during printing. The command cannot be processed. Action 1. Enter the STOP O command. 2. Enter the SPACE n PAGES command. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 6-67...
Page 146 JDE called for more fonts and forms per page than were specified at installation. The job is being aborted. Action 1. Enter the JDE or DJDE command calling for a number of forms and fonts within range established at installation. 2. Restart the job. 6-68 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 147 The system will report data in a “NODEPT” file. Action Enter the ACCOUNT command to establish a file for the department. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on tracking system activity for additional information.) OS2915 Security violation.
Page 148 RCU (Restrict Command Usage) command. Action Obtain the correct password and log on at the required level. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on setting LPS parameters for additional information.) OS2990 Use ‘PROBLEM’ at earliest opportunity.
Page 149: Os Level 3: Printer Problem
3. If the tray does not rise, enter the FEED 2 command to switch to another tray to complete the job. 4. If the problem continues, contact your systems specialist or Xerox Customer Service. Note: CRT refers to the Xerox DocuPrint 180 LPS system controller display. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 6-71...
Page 150 3. Ensure that the length guide is against the paper edge. (Refer to the chapter on feeder trays in your Xerox DocuPrint 180 LPS Operator Guide .) 4. Pull out feeder tray 2, then push it all the way back in. The feeder tray should rise automatically.
Page 151 1. Check printed output. 2. If output is acceptable, press the <CON> key or the Continue button on the printer to resume printing. If print quality is degraded, contact your systems specialist or Xerox Customer Service. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 152 There is an extra sheet in the collection area of the stitcher/stacker. Follow the instructions on the printer display. Action 1. Raise the stitcher/stacker lid and remove the extra sheet from the collection area. 2. Press the <CON> key to resume printing. 6-74 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 153 TRAY 1 IS SET FOR _X_MM PAPER. TRAY 2 IS SET FOR _X_MM PAPER. WARMING UP. BOTH PAPER TRAYS NOT SET FOR SAME SIZE. PRESS i 3. Wait until READY TO PRINT appears on the printer control console display. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 6-75...
Page 154 3. Ensure that the length guide is against the paper edge. (Refer to the chapter on feeder trays in your Xerox DocuPrint 180 LPS Operator Guide .) 4. Pull out feed tray 3, then push it all the way back in. The feed tray should rise automatically.
Page 155 1. Press the <CON> key to ignore the first occurrence of the fault. 2. If the fault continues, enter the STITCH OFF command to turn off the stitching option. 3. Contact your systems specialist or Xerox Customer Service. OS3040 Output offset failure. Set will not be offset A stitcher/stacker offset failure has occurred.
Page 156 Action Remove jammed sheet(s) from area(s) indicated on the printer control console display (Refer to the problem solving chapter in your Xerox DocuPrint 180 LPS Operator Guide .) OS3700 Suspected page-delivery error. Check output. The last printed sheet may not have reached the stacker tray.
Page 157 Action 1. Check the output. 2. Press the <CON> key to resume printing. 3. The message may also appear when a printer fault occurs or if the printer is powered off. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 6-79...
Page 158: Os Level 4: System Or Tape Problem
Action Reenter the command with a value within the acceptable range. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapters on using the font editor and using graphics, or the Xerox DocuPrint 180 LPS Forms Creation Guide .) OS4100 Printer is in diagnostic mode.
Page 159 Action 1. Clean the magnetic tape drive. (Refer to the maintenance chapter in your Xerox DocuPrint 180 LPS Operator Guide .) 2. Reenter the command. 3. If the message reappears, contact your systems specialist or Xerox Customer Service.
Page 160 * If tape input abort job and clean the drive. Then restart job Enter the ABORT I command and clean the tape drive. (Refer to the maintenance chapter in your Xerox DocuPrint 180 LPS Operator Guide .) * Space 1 report Enter the SPACE 1 REPORTS command to skip over the problem report.
Page 161 The system temporarily lost power due to a power outage or a disconnect from its electrical source. Automatic job recovery is being attempted. Action Follow recovery instructions as they appear on the printer control console display. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 6-83...
Page 162 The system Error Log is nearly full. Action Use the PROBLEM command to avoid loss of error log information. (Refer to the problem solving chapter in your Xerox DocuPrint 180 LPS Operator Guide .) 6-84 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 163: Os Level 6: Job Integrity
1. Enter the CONTINUE command, or press the <CON> key to print the job without delimiter sheets. Enter the ABORT job command to cancel the job. 2. Recreate the job, reducing the number of features. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 6-85...
Page 164 1. Enter the ABORT job command to cancel the job and clean the magnetic tape drive to ensure that the read process was not impaired. (Refer to the maintenance chapter in your Xerox DocuPrint 180 LPS Operator Guide .) 2. Restart the job. If the message reappears, do one of the following: Press the <CON>...
Page 165 LBLLIB.SYS file not found. The label processing the library file does not exist on disk. The job will abort. Action Resysgen, if authorized to do so. (Refer to your Xerox DocuPrint 180 LPS System Generation Guide .) Contact your systems specialist. OS6090 Label error: Illegal block length;...
Page 166 1. Press the <CON> key to resume printing. The RTEXT message will not print. Enter the ABORT job command to cancel the job. 2. Recode the RTEXT statement correctly. (Refer to your Xerox DocuPrint 180 LPS PDL Reference .) 3. Restart the job.
Page 167 The system is unable to access the indicated graphic file because the file header is nonexistent or incorrectly formatted. The job will abort. Action 1. Reload the desired file onto disk. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on using graphics for additional information.) 2.
Page 168 Enter the ABORT job command to cancel the job. 2. Recode JDE to match the tape label block count. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on setting LPS parameters for additional information.) 3. Restart the job.
Page 169 The page log entry with the graphics specified will not fit in the page log sector on the system disk. The job will abort. Action Recreate the job, reducing the amount of graphic data. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 6-91...
Page 170 None OS6555 Interpress data extraction error. An error has occurred when the software was decoding information from the Interpress master for use by the Xerox DocuPrint 180 LPS. Action 1. Check for additional messages or instructions on the keyboard display.
Page 171 The job will abort. Action Recode JSL so that paper dimensions (PAPERSIZE command) agree with the BEGIN statement. (Refer to your Xerox DocuPrint 180 LPS PDL Reference .) XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 172 Enter the ABORT I command to cancel the job. 2. Recode JSL or FSL with paper size matching the other paper size specifications in JSL or FSL and restart the job. (Refer to your Xerox DocuPrint 180 LPS PDL Reference .) 6-94 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 173 Action 1. Recode DJDE, using a standard interleaved graphic callout instead of an SD callout. (Interleaved graphic parameter should be T instead of D.) (Refer to your Xerox DocuPrint 180 LPS PDL Reference .) 2. Restart the job. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 174 DJDE processing error: stockset file not found A DJDE stockset called out within the job is not present on the system disk. 1. Enter the correct stockset. (Refer to your Xerox DocuPrint 180 Action LPS PDL Reference .) 2. For assistance, contact your systems specialist or Xerox Customer Support.
Page 175 1. Enter the ABORT command to cancel the job. 2. Recompile PDE correctly. (Refer to your Xerox DocuPrint 180 LPS PDL Reference .) 3. Reload the PDE file to the system disk. (Refer to your Xerox DocuPrint 180 LPS PDL Reference .) 4. Restart the job.
Page 176 DJDE processing error: maximum Forms/Fonts exceeded. DJDE specified a PDE calling for forms and/or fonts in excess of the system maximum. Action 1. Recode the DJDE with fewer fonts/forms. (Refer to your Xerox DocuPrint 180 LPS PDL Reference .) 2. Restart the job. OS6723 DJDE processing error: Insufficient memory for PDE.
Page 177 The FEED command was used but a STOCKSET statement is not in effect. Action Reenter the DJDE command, specifying a STOCKSET. (Refer to your Xerox DocuPrint 180 LPS PDL Reference , chapter 4, “Dynamic Job Descriptor Entries.”) OS6731 File x processing aborted—data format error.
Page 178 .OSD, .SAF, .SYS, .$Y$, or .TSK. The file will not be copied to disk. Action Recode DJDE, specifying only files with acceptable file type extensions. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on LPS processing for additional information.) OS6736 File processing error—no label record.
Page 179: Xerox Customer Support Center
During printing, a file was discovered to be incorrectly formatted, or wrong switch code was entered in CCL MERGE command. Action Resend job, correcting switch codes if necessary. (Refer to your Xerox DocuPrint 180 LPS Reference Manua l, “Communications interface” chapters.) OS6755 Word processing merge job - no merge file.
Page 180 CWP jobs. Job is aborting. Action 1. Restart job, using correct font tape. 2. Call Xerox Font Center for information on replacing font. OS6761 Too many SEF Font mapping errors. An exceedingly large number of Short Edge Feed font mapping errors has occurred.
Page 181 Check the catalog-name and retry the command. OS6823 Black-format FILENAME.FRM references color-format logo(s). The Xerox DocuPrint 180 LPS detects that the form being printed in black-only format references a logo in color format. Action Convert the form to color format using the File Conversion Utility (FCU).
Page 182 Action Check printed output. If overflow has occurred, recreate the job using a smaller font or fewer lines per page. (Refer to your Xerox DocuPrint 180 LPS PDL Reference .) OS6905 Data origin off page. Check output.
Page 183 Unable to rasterize local density problem page. An imaging error occurred while attempting to rasterize a page with a local density problem. The page cannot be rasterized; i.e., a bitmap image of the page cannot be produced. Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 6-105...
Page 184 The font specified for Routing Text was given a Font Index number in excess of that contained in PDE list. Action 1. Recode the RTEXT font index statement with an appropriate index number. (Refer to your Xerox DocuPrint 180 LPS PDL Reference .) 2. Restart the job. OS6961 Invalid font index for page numbering.
Page 185: Os Level 7: System Problem
The job will abort. Action 1. Reenter the statement correctly in JDL. (Refer to your Xerox DocuPrint 180 LPS PDL Reference or Xerox DocuPrint 180 LPS Operations Reference chapter on setting LPS parameters for additional information.)
Page 186 The system is operating online, but a JDE was specified that cannot be used online. JDE does not define the HOST type correctly. Action 1. Specify the correct JDE. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on LPS processing for additional information.) 2.
Page 187 Multiple begins in PDE not supported—Job aborted The multiple begins specified in the PDE cannot be completed. The job has been aborted. Action 1. Recode the PDE. (Refer to your Xerox DocuPrint 180 LPS PDL Reference .) 2. Restart the job. OS7450 Graphic sample not allowed by JDE.
Page 188 The memory needed by input task to accomplish DJDE/Delimiter processing exceeds the memory available. Action 1. Reduce the complexity of form. (Refer to your Xerox DocuPrint 180 LPS Forms Creation Guide .) 2. Rerun the job to determine if failure is an intermittent CPU/ memory failure.
Page 189 Fonts specified in JDE/DJDE exceed the available font memory. The job is being aborted. Action 1. Recode PDE with a smaller set of fonts. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on setting LPS parameters for additional information and your Xerox DocuPrint 180 LPS PDL Reference .)
Page 190 A feed stock has been specified that is not contained in the current stockset. Action Restate your cluster command to include that feed stock. (Refer to the chapter on feeder trays in your Xerox DocuPrint 180 LPS Operator Guide . 6-112 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 191: Os Level 8: Probable Severe Software Error
Enter the HIP ONLINE;START command, if desired. Resend the job. If the problem continues, resysgen, if authorized to do so, Contact your systems specialist (refer to your Xerox DocuPrint 180 LPS System Generation Guide ). XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 192 Enter the HIP ONLINE;START command, if desired. Resend the job. If the problem continues, resysgen, if authorized to do so, Contact your systems specialist (refer to your Xerox DocuPrint 180 LPS System Generation Guide ). OS8052 IPD dynamic memory; initialization failure.
Page 193 The input task encountered a system disk error during a sample print job. Action 1. Restart the job. 2. If the failure recurs, contact your systems specialist or Xerox Customer Service. OS8320 Input cannot open accounting file. The accounting file on the system disk cannot be accessed.
Page 194 Drive xxx not useable: no disk ID. The indicated disk drive cannot be used because it has not been formatted for your system. Action Format the disk. (Refer to your Xerox DocuPrint 180 LPS System Generation Guide .) 6-116 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 195 The indicated disk drive cannot be used because it was moved from another system and was not formatted for this one. Action Reformat the disk. (Refer to your Xerox DocuPrint 180 LPS System Generation Guide .) OS8560 Drive xxx not useable: should be drive yyy.
Page 196 The input task is unable to read a font file header due to software or system disk/CPU problems. The job will abort. Action 1. Reload the font file. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on using the font editor for additional information.) 2.
Page 197 1. Recompile the form with the correct file header. (Refer to your Xerox DocuPrint 180 LPS Forms Creation Guide .) 2. Reload form file to system disk. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on managing LPS resources for additional information.)
Page 198 Boot button and entering B. 4. Restart the job. 5. If the problem continues, resysgen, if authorized to do so (refer to your Xerox DocuPrint 180 LPS System Generation Guide ), Contact your systems specialist. OS8985 Unable to initiate HIP task.
Page 199: Os Level 9: Probable Severe Hardware Error
RNAME COREIM.SYS to some well-known name (e.g., BADnnn.TMP). Restore COREIM.SYS via a resysgen, if authorized to do so, or contact your systems specialist (refer to your Xerox DocuPrint 180 LPS System Generation Guide .) Resend the job. Contact your systems specialist or Xerox Customer Support to log the bad sector and delete the well-known name.
Page 200 RNAME ETNMSG.SYS to some well-known name (e.g., BADnnn.TMP). Restore ETNMSG.SYS via a resysgen, if authorized to do so, or contact your systems specialist (refer to your Xerox DocuPrint 180 LPS System Generation Guide .) Resend the job. Contact your systems specialist or Xerox Customer Support to log the bad sector and delete the well-known name.
Page 201 1600 bpi magnetic tape drive. Action 1. Clean the magnetic tape drive. (Refer to the maintenance chapter in your Xerox DocuPrint 180 LPS Operator Guide .) 2. Check the tape density. 3. Restart the job and/or mount a tape of correct density for the tape drive.
Page 202 Enter the ABORT O command to cancel the report. 2. Restart the job. 3. If the problem continues, contact your systems specialist or Xerox Customer Service. Note: CRT refers to the Xerox DocuPrint 180 LPS system controller display. OS9320 Graphic imaging error. Page won‘t be printed. ABORT O.
Page 203 Contact your systems specialist or Xerox Customer Service with the above information. Note: CRT refers to the Xerox DocuPrint 180 LPS system controller display. OS9400 Fatal disk error: Call for service; DO NOT REBOOT! A very serious system disk error has occurred for which no operator action should be attempted.
Page 204 2. If the failure recurs, a problem with the system disk is indicated. Contact your systems specialist or Xerox Customer Service. Note: CRT refers to the Xerox DocuPrint 180 LPS system controller display. OS9551 Unable to recover from disk error. Resetting system.
Page 205 A fatal error in the online interface has occurred during power-up. Action 1. Repeat the powerup sequence. (Refer to the powering on and off chapter in your Xerox DocuPrint 180 LPS Operator Guide .) 2. If the failure recurs, contact your systems specialist or Xerox Customer Service.
Page 206 1. Reboot the system by pressing the Boot button, then entering 2. If the message reappears, resysgen if authorized to do so (refer to your Xerox DocuPrint 180 LPS System Generation Guide ), Contact your systems specialist or Xerox Service Support Center.
Page 207 Action 1. Reboot the system by pressing the Boot button, then entering 2. If the message reappears, resysgen if authorized to do so (refer to your Xerox DocuPrint 180 LPS System Generation Guide ), Contact your systems specialist. OS9996 Unable to read executive file.
Page 208 A hardware problem has occurred that is sufficiently severe to prevent operation of the system. Action 1. Reboot the system by pressing the Boot button, then entering 2. If message reappears, contact your systems specialist or Xerox Customer Service. 6-130 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 209: Pdl (Job Source Library Compilation) Messages
Level 8—probable severe software errors Level 9—probable severe hardware errors Note: For instructions on compiling JSLs and list of PDL commands, refer to your Xerox DocuPrint 180 LPS PDL Reference . PD0100 Noreplace specified. A JDL object file that already exists was recompiled with NOREPLACE option.
Page 210 No source file will be created. A source file cannot be created due to an unspecified error. Action Check the file and make corrections, if needed. (Refer to your Xerox DocuPrint 180 LPS PDL Reference .) PD0510 Source file is full.
Page 211 An attempt was made to access it at a wrong logon level. Action To access the file, obtain the correct password and logon at Level 5. (Refer to your Xerox DocuPrint 180 LPS Operations Reference , chapter 1, “System setup,” “File access and command protection commands” section.) PD4500 Tape read error.
Page 212 A large enough file was not created to allow complete transfer from disk during input or output. Action 1. Retry compiling JSL. (Refer to your Xerox DocuPrint 180 LPS PDL Reference . 2. If the problem continues, contact your systems specialist or...
Page 213 Open error —Print File. The system is unable to open the print file due to a system disk error. Action 1. Retry compiling. 2. If the message reappears, contact your systems specialist or Xerox Customer Service. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 214 The requested output file cannot be opened. Action 1. Verify the output file name and reenter the command Close the source file and resend it. 2. If the message reappears, contact your systems specialist or Xerox Customer Service. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 215 8PG (PURGE command) messages These messages may appear during process of purging disk or print file. Refer to your Xerox DocuPrint 180 LPS Operations Reference for detailed information about the PURGE command. PG0100 Processing the entire disk. The PURGE D command was entered. The system is clearing all unused areas of the disk, including the print file.
Page 216: Pg (Purge Command) Messages
A PURGE command was entered while purge was already in progress. The command is ignored. Action None PG1800 Purge processor aborting The ABORT command was entered. The purge process is being terminated. Action None XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 217: Pr (Hardcopy Graphics Printing Command) Messages
These messages may appear during the HARDCOPY process (printing copy of graphic .IMG files with comprehensive descriptor page). Refer to your Xerox DocuPrint 180 LPS Operations Reference for information about the HARDCOPY command. PR1000 All files hardcopied, hardcopy exiting.
Page 218 PR2710 Scale factor invalid, check and retry. The “n/d” scale parameter of the HARDCOPY command was entered incorrectly. Reenter the command correctly. (Refer to your Xerox DocuPrint 180 Action LPS Operations Reference chapter on running print jobs.) PR2720 HPOS value out of range, check and retry.
Page 219 A disk error occurred while a .XCS file sent from a workstation was being created on disk. File creation is aborted. Action 1. Resend the file. 2. If the problem recurs, contact your systems specialist or Xerox Customer Service. PR9520 Cannot open RECTSK.SYS.
Page 220 PR (HARDCOPY GRAPHICS PRINTING COMMAND) MESSAGES XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 221: Psc (Printer Subsystem Controller Command) Messages
Action None PS1190 Invalid syntax. The PSC command line contains incorrect syntax. Reenter the command line using correct syntax. (Refer to your Xerox Action DocuPrint 180 LPS Operations Reference chapter on managing LPS resources for additional information.) PS8888 PSC cannot complete due to an unrecoverable error.
Page 222 PS9001 CSI download error —CSI not loaded. The CSI board is not functional. Action Contact your systems specialist or the Xerox Customer Service. PS9002 SCSI download failed—executing from ROM. The firmware downloaded to the SCSI controller failed. The SCSI controller is executing from a ROM chip.
Page 223 PSC (PRINTER SUBSYSTEM CONTROLLER COMMAND) MESSAGES PS9960 Download error: SAN nn.nn This message provides the Software Analysis Code (SAN) needed by Xerox Customer Service to correct the download error. Action None PS9961 Download error: SAN nn.nn This message provides the Software Analysis Code (SAN) needed by Xerox Customer Service to correct the download error.
Page 224 PSC (PRINTER SUBSYSTEM CONTROLLER COMMAND) MESSAGES 10-4 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 225: 11. 11Scale Command Messages
The SCALE command enables scanned graphic images (fonts, forms, and logos) to print at an enlarged or reduced size under certain conditions. Refer to your Xerox DocuPrint 180 LPS Operations Reference chapters on HIP-accessed communicating modes and using graphics for detailed information about the SCALE command.
Page 226 The requested file cannot be scaled. Action Verify the file type and reenter the command. The file type must be FRM, FNT, FN6, LG0, or LG6. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on managing LPS resources for additional information.)
Page 227 2. Restore the file from a backup source (e.g., tape, floppy, or host). 3. Recreate the file using FDL if an FRM file. 4. Contact your systems specialist or Xerox Customer Service to log the bad sector and delete the well-known name. File already exists, overwrite xxxx (Yes or No)? The requested file already exists.
Page 228 Reenter the output name using a font from the specified directory. Acceptable file types are FNT, FN6, FR6, LG0, and LG6. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on managing LPS resources for additional information.) **File, xxxx, can not be scaled (unknown error)** The requested file cannot be scaled due to an unknown error.
Page 229 **Font scaling resulted in size mismatch** Scaling caused a mismatch between the estimated and actual bitmap sizes. Action Contact your systems specialist or Xerox Customer Support. **Font xxxx is not alpha-numeric** The font or logo is either Kanji or corrupted. Action 1.
Page 230 SCALE. Action Reenter the SCALE command, including the input file name. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on managing LPS resources for additional information.) **Only one line per TL supported** A nonstandard FRM file has been used that is not supported by SCALE.
Page 231 **Run font through fix on CD/IG Version 2 or higher** The font must be modified through the FIX command before scaling. Action 1. Enter the appropriate FIX command. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on managing LPS resources for additional information.) 2.
Page 232 Text line number n is being scaled. Action None Scaling TL/DL nn The identified text line/display list is being scaled. Action None Scaling TL/DL buffers: The body of the form is being scaled. Action None 11-8 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 233: Sfs (Status File Services Command) Messages
The following messages refer to the status file services (SFS) command, which creates, clears, displays, prints, and stores status file information. Refer to your Xerox DocuPrint 180 LPS Operations Reference chapters on tracking system activity and managing system resources for detailed information about the SFS command.
Page 234 An SFS command was entered, but Status File had already been cleared and no new file was created. Action 1. Enter the SFS CREATE command to recreate the Status File. 2. Reenter the desired SFS command 12-2 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 235 The command is being ignored. Action Recompile the form, restating the command correctly. (Refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on setting LPS parameters for additional information.) SF6020 Column ignored.
Page 236 The column width value specified in the WIDTH statement for the user-created form is smaller than the actual content of the column. The system will enter only as many characters as will fit, ignoring the rest, and compile the form. Action None. 12-4 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 237 Recompile the form, entering the CONTENT statement correctly. SF9500 Irrecoverable disk or conversion error. A fatal error has occurred on the system disk. SFS is aborting. Action Contact your systems specialist or Xerox Customer Service. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 12-5...
Page 238 SFS (STATUS FILE SERVICES COMMAND) MESSAGES 12-6 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 239: System Verification Error Messages
Action 1. Verify that your values and/or syntax are correct and retry the command. 2. If the message reappears, contact your supervisor or systems support specialist. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 13-1...
Page 240 Main memory missing: Bank(s) xx, xx, xy, xz, ... Message appears if any memory specified during the system configuration phase is either not present or has had data loss. Banks are displayed in 16K sections. Action None. 13-2 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 241 Action None. Updates Non-Volatile Memory locations: The parameters you have specified have updated existing non- volatile memory (NVM) data. Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 13-3...
Page 242 SYSTEM VERIFICATION ERROR MESSAGES 13-4 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 243: Summary Sheet Error Messages
14Summary sheet error messages Your Xerox DocuPrint 180 LPS communicates Interpress error messages to you on the system controller display and on summary sheets that accompany your printed output. Summary sheets are placed at the end of printed jobs. Errors printed on a summary sheet have three main fields: •...
Page 244: Appearance Error Message
Meanings and appropriate actions to take, if any, are provided in the righthand column. For further information about Interpress, refer to your Xerox DocuPrint 180 LPS Operations Reference chapter on HIP-accessed communicating modes. Note: In the Meaning/action column of this chapter, the term operand refers to that which is acted upon (i.e., data) in an operation...
Page 245 SUMMARY SHEET ERROR MESSAGES Form file not found: “fileType>fileName.” When processing an SIF, no file with the name filename.filetype was locally available to the Xerox DocuPrint 180 LPS. Action Load the form on the LPS or change the form reference in the document and resend the document.
Page 246: Appearance Warning Messages
If so, load the correct font on the printer and reprocess the document. Appearance Warning (page n): Invalid packed pixel array data. During the decompression of a Xerox/Packed pixel array, the format of the pixel array is determined to be invalid. Action None.
Page 247 SHIFT JSL command. Action None. Invalid packed pixel array data. During the decompression of a Xerox/Packed pixel array, the format of the pixel array is invalid. Action None. Logo off paper on page n at <nn.nnn>,<nn.nnn> [inches];...
Page 248 None. Paper selection error; medium n undefined by master. The document selected undefined stock for a particular page range in the document. The selection was ignored for the entire page range. Action None. 14-6 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 249 The line may be entirely off the page and not visible. If the error is the result of a family substitution, the correct family may be loaded on the Xerox DocuPrint 180 LPS and the document resent. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 250: Fatal Error Messages
2. If the error continues, increase the size of the spool space by modifying HIP.LIB. ENCODED VECTOR not well-defined. An error in the format of a printing instruction property vector was detected. Action None. 14-8 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 251 (GVG or GHO). Action None. No resources; insufficient dynamic memory. Virtual memory space was exhausted during Interpress master processing and the job was aborted. Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 14-9...
Page 252 Action None. Too many errors in document. Too many errors were found in the document to continue processing. Action 1. Correct the previous errors reported on the summary sheet. 2. Resend the document. 14-10 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 253 Note: In this message, the letter “B” indicates an octal value. Unexpected error. Code = n. An error occurred during processing. Action Contact your systems specialist or Xerox Customer Support. Unknown state discovered during attempted MARK Recovery. MARK Recovery failed. Action 1.
Page 254: Informational Messages
The document requested that a comment be added to the summary sheet. Action None. Document Generated Comment “documentComment”. A comment field is taken from the printing instructions or protocol and is displayed on the summary sheet. Action None. 14-12 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 255 This message is preceded by the ... Font Problem ... message. Action None. Note: In this message, the letter “B” indicates an octal value. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 14-13...
Page 256 Most of the messages are generated by information in the printing instructions. If a particular message is not included, the printing instructions in the document did not define the corresponding entry. 14-14 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 257: Master Error Messages
Interpress family mapping does not contain the requested point size. Action Invoke the FIS utility to add the desired orientation or allow point size substitution for the Interpress family via the IFU SUBSTITUTE command. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 14-15...
Page 258 The form file in the previous Problem with insert file: ... message references an image that does not exist on the LPS. Action 1. Copy the identified image onto the printer Change the form referenced Modify the requested form. 2. Resend the document. 14-16 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 259 In processing an Interpress operator, the required operand type was not found on the stack. Action None. Invalid argument(s) value for operator: <operatorName>. An invalid value for the operator was found. Action None. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 14-17...
Page 260 SUMMARY SHEET ERROR MESSAGES Master not well-formed; bad document header. The Interpress header, “Interpress/Xerox/n.0...” was not found in a file that required one. The file is either the Interpress master or an SIF. A SIF problem is preceded by the error “Master Warning (page n): Problem with insert file: "fileType>fileName."”...
Page 261 COMPOSED operator. An internal error in processing a composed operator was found. Action Contact your systems specialist or Xerox Customer Service. Parse failure; MARK not found during COUNT/UNMARK operation. An UNMARK or UNMARK0 operation failed to find a MARK on the stack.
Page 262 Property name not found during GETP operation. A property vector did not contain the requested property. Action None. Zero divide attempted. A zero divisor was found in the master or was due to loss of precision. Action None. 14-20 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 263: Master Warning Messages
Action None. Too many “Page Warnings” on this page. Too many page warnings were found to continue processing the page and a MARK Recovery to the next page was performed. Action None XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 14-21...
Page 264: System Problem Messages
Action 1. Rename RTXFIL.SYS to a well-known name (e.g., BADBKn.SYS). 2. If authorized to do so, perform a resysgen to restore RTXFIL.SYS Contact your systems specialist. 14-22 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 265 An error was found while reading the system disk. The system disk contains one or more bad sectors that are not included in the bad block file. Action 1. Resend the document. 2. If the problem continues, call Xerox Customer Service. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 14-23...
Page 266 Action 1. Rename IPFNTS.SYS to a well-known name (e.g., BADBKn.SYS) 2. Recompile IPFNTS by keying in the IFU IPFNTS command. 14-24 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 267: Xerox Docuprint 180 Lps Additional Messages
15Xerox DocuPrint 180 LPS additional messages These messages may appear on your Xerox DocuPrint 180 LPS PC User Interface (PC UI). How the messages are organized Messages that appear on your screen with numbers in front of them are listed in the first part of this chapter in numerical order. Messages...
Page 268 XEROX DOCUPRINT 180 LPS ADDITIONAL MESSAGES General action to take As a general rule, when an error message is displayed in a message window on your Xerox DocuPrint 180 LPS PC User Interface, the recommended actions are as follows: •...
Page 269: Numbered Xerox Docuprint 180 Lps Messages
Messages 7 through 36 Messages 7 through 36 appear when serious User Interface software problems occur. For all of these messages, call for Xerox service. Messages 41 and 42 At least one of the main UI windows did not create Microsoft Windows cannot create a window required by the SysUI.
Page 270 XEROX DOCUPRINT 180 LPS ADDITIONAL MESSAGES Signal expected but not received The PC user interface was expecting to receive signal data. Action Select the OK header button to retry the process. If the problem persists, call Xerox Customer Service. Protocol Error An incomplete or damaged protocol packet was received.
Page 271 XEROX DOCUPRINT 180 LPS ADDITIONAL MESSAGES Can’t post SM_COMM message Posting of the SM_COMM message to the application’s queue failed. The communication with the system controller has not been initiated. Action 1. Ensure no other Microsoft Windows applications using the communication ports are running.
Page 272 XEROX DOCUPRINT 180 LPS ADDITIONAL MESSAGES Data Set Ready timeout The Data Set Ready timeout has been exceeded. Action Select the OK header button to retry the process. If the problem persists, call Xerox Customer Service. Frame error detected The communications driver detected a framing error.
Page 273 XEROX DOCUPRINT 180 LPS ADDITIONAL MESSAGES Parity error while receiving The user interface does not use this feature of RS232. Action Select the OK header button to retry the process. If the problem persists, call Xerox Customer Service. Transmit queue full The communication driver’s transmit queue is full.
Page 274 XEROX DOCUPRINT 180 LPS ADDITIONAL MESSAGES Invalid custom signal data The format of this system controller signal is invalid. Action Select the OK header button to retry the process. If the problem persists, call Xerox Customer Service. Messages 1538 through 1572...
Page 275 XEROX DOCUPRINT 180 LPS ADDITIONAL MESSAGES 1545 Invalid mouse speed rate An incorrect mouse speed was specified. Action Select the OK header button to retry the process. If the problem persists, call Xerox Customer Service. 1546 Missing directory name in config record The second parameter of a “DIRNAME”...
Page 276 XEROX DOCUPRINT 180 LPS ADDITIONAL MESSAGES 1554 Invalid comm device; must be 1 or 2 The parameter value of the “DEVICE” statement in the SysUI configuration file is invalid. Action Select the OK header button to retry the process. If the problem persists, call Xerox Customer Service.
Page 277 XEROX DOCUPRINT 180 LPS ADDITIONAL MESSAGES 1561 Cannot create UI Dirty File; UI cannot run MS-DOS cannot create a SysUI dirty file. Action Select the OK header button to retry the process. If the problem persists, call Xerox Customer Service.
Page 278 XEROX DOCUPRINT 180 LPS ADDITIONAL MESSAGES 1568 No record types specified for console log report The parameters of the optional “REPTYPE” statement in the SysUI configuration file are missing. Action Select the OK header button to retry the process. If the problem persists, call Xerox Customer Service.
Page 279 1. Restart the PC user interface hardware from Power On. 2. Ensure no other Microsoft Windows applications are running. 3. Select the OK header button to retry the process. If the problem persists, call Xerox Customer Service and provide the UI Crash Log, if installed. 3550 Unable to read last Console Log Data record Unable to read last record from console log.
Page 280 1. Restart the PC user interface hardware from Power On or DOS command line. 2. Select the OK header button to retry the process. If the problem persists, call Xerox Customer Service and provide the UI Crash Log, if installed. 3564 Invalid client data buffer handle Calling function‘s buffer handle to be used to store data is invalid.
Page 281 These are general messages. Select the OK header button to retry the process. Action If the problem persists, call Xerox Customer Service. 4077 through 4085 These messages relate to the loading of the Master File. Select the OK header button to retry the process.
Page 282 Select the OK header button to retry the process. Action If the problem persists, call Xerox Customer Service. Messages 4500 through 4506 The following messages (4500 through 4506) are the results of problems/warnings/status that could occur when displaying objects.
Page 283 Memory controlled by DDB (Dialog Data Base) functions cannot be unlocked. Action 1. Restart the UI from Power On. 2. If the problem persists, call for Xerox Customer Service and provide the UI Crash Log, if available. 9044 Insufficient memory Insufficient memory to allocate DDB (Dialog Data Base) file control table.
Page 284 1. Restart the PC user interface hardware from Power On. 2. Ensure no other Microsoft Windows applications are running. 3. Select the OK header button to retry the process. If the problem persists, call Xerox Customer Service and provide the UI Crash Log, if available. 9059 No index file on reopen error Intermediate DDB (Dialog Data Base) index file not found.
Page 285 (MM, CD or TDB). Action Contact Xerox Customer Service to determine recovery point. 9061 Index file error code Intermediate DDB (Dialog Data Base) index file could not be opened.
Page 286 Microsoft Windows GlobalAlloc has (or would have) failed. Action 1. Ensure no other Microsoft Windows applications are running. 2. Restart the PC user interface from Power On. 3. If problem persists, call Xerox Customer Service and provide the UI Crash Log, if available. 9538 Can’t lock memory A NULL or invalid handle has been (or would have been) passed to GlobalLock.
Page 287 Accelerated access was attempted on a file and it was unsuccessful in closing. Action If the problem persists, call Xerox Customer Service. A System error has caused the log print request to be terminated. A System error has occurred. If the problem persists, save the Console Log and call for Service.
Page 288 Following the end of report printing, the phase manager cannot find a phase record to manage the completion of the audit log. Action If the problem persists, call Xerox Customer Service. Attempting to establish communication with the Printer. The system has been booted or PSC has been entered, so the system controller is trying to establish low level communication with the printer.
Page 289 XEROX DOCUPRINT 180 LPS ADDITIONAL MESSAGES AUD file Mgr extended file not found. Action If the problem persists, call Xerox Customer Service. AUD File Mgr file access denied due to read only mode or owner name. AUD File Mgr file access denied due to read only mode or owner name.
Page 290 XEROX DOCUPRINT 180 LPS ADDITIONAL MESSAGES AUD File Mgr file not found. Action If the problem persists, call Xerox Customer Service. AUD File Mgr file not open. Action If the problem persists, call Xerox Customer Service. AUD File Mgr file table full.
Page 291 XEROX DOCUPRINT 180 LPS ADDITIONAL MESSAGES AUD File Mgr key buffer too short for requested index path. Action If the problem persists, call Xerox Customer Service. AUD File Mgr key length invalid. Action If the problem persists, call Xerox Customer Service.
Page 292 XEROX DOCUPRINT 180 LPS ADDITIONAL MESSAGES AUD File Mgr pre-image i/o error. Action If the problem persists, call Xerox Customer Service. AUD File Mgr pre-image open error. Action If the problem persists, call Xerox Customer Service. AUD File Mgr record length too small or exceeds page size.
Page 293 XEROX DOCUPRINT 180 LPS ADDITIONAL MESSAGES Audit Log complete. The current report has completed the audit log. Action None. Audit Log delete complete. A request to delete a log or logs has completed. Action None. Audit Log disk approaching full.
Page 294 Action Check JSL or DJDE in job stream to ensure that all Page Detail BTEXT keywords and parameters are correct. Parameters to check are SEQ, PRA, and TXT. If the problem persist, call Xerox Customer Service BTEXT signal text invalid A BTEXT keyword or parameter is invalid.
Page 295 Cannot access memory for record position pointer. Attempting direct read of file but list of records does not exist. Action If the problem persists, call Xerox Customer Service. Cannot access memory for report format buffer. Report format buffer does not exist.
Page 296 Cannot allocate memory for report display list. Insufficient system memory exists to display a list of Audit Logs. Action Try a filtered list of logs, if the problem persists, call Xerox Customer Service. Cannot allocate memory for report phase record.
Page 297 Action Rename any file that has these terms in the file name. Client-Layer is established The Xerox DocuPrint 180 LPS is communicating normally. Action Before printing, check the PC user interface or printer control console for instructions on clearing any existing faults. If you are instructed to...
Page 298 Command sequence error, record number not equal to last +1. One or more of the report definition commands are out of order. Action If the problem persists, call Xerox Customer Service. Communication with the Printer is established Action Low-level communication between the system controller and the printer has been established.
Page 299 XEROX DOCUPRINT 180 LPS ADDITIONAL MESSAGES Duplicate AUD File Mgr key not allowed. Action If the problem persists, call Xerox Customer Service. Duplicate key value updating master Directory file for completion copy. The Master Directory record already exists, and as a result the new...
Page 300 XEROX DOCUPRINT 180 LPS ADDITIONAL MESSAGES Error changing directory Action If the problem persists, call Xerox Customer Service. Error closing report format output file. The record manager is unable to close the output file that contains the formatted audit log text. Audit logs cannot be displayed or printed.
Page 301 Check the JSL or DJDE in the job stream to ensure that all BTEXT RRA keywords and parameters are correct. Expanded Memory Manager reports error to Btreive. Action If the problem persists, call Xerox Customer Service. Extended Get/Step operations have exceeded pre-image buffer. Action If the problem persists, call Xerox Customer Service.
Page 302 This could occur during PC UI session startup. Windows has failed to allow the auditor feature to create a window. Action If the problem persists, call Xerox Customer Service. Failure to create Audit Logging window. This could occur during PC UI session startup. Windows has failed to allow the auditor feature to create a window.
Page 303 The auditor is unable to open the in-process audit log. Audit logging will not take place. Action If the problem persists, call Xerox Customer Service. Failure to register DDL class window for auditor. This could occur during PC UI session startup. Windows has failed to...
Page 304 XEROX DOCUPRINT 180 LPS ADDITIONAL MESSAGES FCG Exiting: Invalid Profile Encountered. The following message is displayed if the information necessary for the FCG SHOW command is not present on the system. Action None. FCG Exiting: Invalid profile—missing semicolon (;) A semicolon is required at the end of a profile label and its parameters.
Page 305 XEROX DOCUPRINT 180 LPS ADDITIONAL MESSAGES File cannot be accessed ..The file is too large for the PC Editor to process. Action If the file is an ESS file, use EDI in the message window. File could not be emptied or deleted. Ensure that the filename is valid.
Page 306 Audit Log. Action If the problem persists, call Xerox Customer Service. Filter file has invalid signature. The filter file(s) has been damaged and has lost its identifying signature. The file may be corrupted. Audit Logging is not prevented, but no operational messages will be logged in any Audit Log.
Page 307 XEROX DOCUPRINT 180 LPS ADDITIONAL MESSAGES Incorrect field offset for Extended Get/Step operation. Action If the problem persists, call Xerox Customer Service. Initializing Client-Layer protocol The system controller has established low-level communication with the printer, and is now trying to establish high-level message communication with the printer.
Page 308 Invalid AUD File Mgr file name. Action If the problem persists, call Xerox Customer Service. Invalid AUD File Mgr key position - exceeds record length. Action If the problem persists, call Xerox Customer Service.
Page 309 XEROX DOCUPRINT 180 LPS ADDITIONAL MESSAGES Invalid Btreive alternate collating sequence definition. Action If the problem persists, call Xerox Customer Service. Invalid buffer for Extended insert operation. Action If the problem persists, call Xerox Customer Service. Invalid command syntax - ARx.
Page 310 A DEC command has an invalid parameter. The report definition file may be corrupt. Action If the problem persists, call Xerox Customer Service. Invalid parameter - FIRST command. A FIRST command has an invalid parameter. The report definition file may be corrupt.
Page 311 A JUSTIFYX command has an invalid parameter. The report definition file may be corrupt. Action If the problem persists, call Xerox Customer Service. Invalid parameter - LWID command. An LWID command has an invalid parameter. The report definition file may be corrupt.
Page 312 XEROX DOCUPRINT 180 LPS ADDITIONAL MESSAGES Invalid response for BTEXT DAR default reporting parameter. The default reporting parameter is incorrectly specified. Action Check JSL or DJDE in the job stream to ensure that all BTEXT DAR keywords and parameters are correct.
Page 313 Log xxx cannot be created. The console log cannot be saved to the floppy diskette. Action If problem persists, contact your systems specialist or Xerox Customer Service. Log xxx does not exist. The requested console log file name does not exist.
Page 314 Action 1. Press the reset button on the PC user interface processor. 2. If the problem persists, call Xerox Customer Service. Log xxx is unreadable and cannot be (emptied/deleted/printed/ displayed/saved). Use a backup log. The saved console log is unreadable and no action can be performed on it.
Page 315 The definition file may be corrupted and should be replaced. Action If the problem persists, call Xerox Customer Service. No formatting window. Although the formatting window was created, it has somehow been destroyed, preventing formatting of any Audit Log for display or printing.
Page 316 Action Call Xerox Customer Service. Number of AUD File Mgr keys specified invalid for page size. Action If the problem persists, call Xerox Customer Service. Number of accelerated files exceeds number of available AUD File Mgr buffers. Action If the problem persists, call Xerox Customer Service.
Page 317 XEROX DOCUPRINT 180 LPS ADDITIONAL MESSAGES Printer is ready. Informational message. The Xerox DocuPrint 180 LPS is communicating normally and is ready to print. There are no existing faults or hints. Action None. Printer is reinitializing. Informational message. Action None.
Page 318 A sheet delivery signal has been received but no output phase exists for the report. Auditor has not recorded start of output. Action If the problem persists, call Xerox Customer Service. Sheet delivery signal but not processing output phase. A sheet delivery signal has been received but no output phase exists for the report.
Page 319 The note cannot be saved because of incorrect file format. Action 1. Follow the message instructions. 2. If problem persists, call your systems specialist or Xerox Customer Service. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE 15-53...
Page 320 Retry the operation with filters to reduce the number of logs that will be listed. Use the Jobs option to reduce the number of logs that will be listed. If the problem persists, call Xerox Customer Service. Too many audit jobs to list. Try filter.
Page 321 Variable length portion of page unreadable by Step Direct operation. Action If the problem persists, call Xerox Customer Service. Waste Management signal but no output phase record exists. Waste management data has been received while logging but no phase record is active to enable the data to be logged.
Page 322 XEROX DOCUPRINT 180 LPS ADDITIONAL MESSAGES 15-56 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 323: Xerox Customer Support Center
AXerox support services Xerox support services are there to help you if your laser printing system should develop a severe hardware, software, or applications problem. If a problem continues after you have tried all remedial actions suggested in this guide, first notify your lead operator or systems specialist (depending on your site’s procedures).
Page 324: Xerox Support Services
Xerox DocuPrint 180 LPS Operator Guide have not resolved the problem. The Xerox Customer Service Support Center is referred to as “Xerox Customer Service”...
Page 325: Xerox Font Center
Xerox Font Center The Font Center can send you samples and catalogs of the fonts available for your Xerox DocuPrint 180 LPS, and can take orders for licensed and custom fonts. Call the Xerox Font Center for information or to place an order at:...
Page 326 XEROX SUPPORT SERVICES XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 327 Captures the sheet delivery information for every page in an audited report, certain details about each sheet, the planned and actual report control totals, and waste management. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE GLOSSARY-1...
Page 328 Data transmission in which synchronization of characters is controlled by timing signals generated at the sending and receiving stations. Abbreviation for binary digit, the smallest unit of information recognized by a computer. See also binary digit. GLOSSARY-2 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 329 (sometimes called a circuit, facility, or link). 2. In computers, a path for communication between the central processing unit (CPU) and input/output units, or between the CPU and peripheral devices. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE GLOSSARY-3...
Page 330 Code representing alphanumeric information, for example, ASCII. character code identifier Code associated with the universal identifier “Xerox” to indicate the version of the Xerox character code standard used to code Interpress strings. character set Number of different characters used by a particular device, including alphabetic, numeric, and special characters such as symbols.
Page 331 Point on the x and y axis that determines a grid position. copy To duplicate data in a new location or on an additional storage medium, for example, to copy files from disk to tape. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE GLOSSARY-5...
Page 332 Value assigned to a field by the system. Default fields may be used for such items as document formats, menu selections, input fields, font selection, and paper or image size. The default value of a field may be changed. GLOSSARY-6 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 333 Use of graphic objects, usually lines or boxes, that bleed off the edge of the physical page. See also physical page. electronic publishing Integrated production of documents on demand, using digitally stored documents, computerized composition, and electronic printing systems. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE GLOSSARY-7...
Page 334 Nonspacing accent characters that can be combined with characters and printed as a composite. font Set of images, usually characters and symbols, having common characteristics such as style, width, height, and weight. GLOSSARY-8 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 335 Nonoptimal adjustment of particular FIS fonts in terms of point size and orientation. hardware Physical components, such as mechanical, magnetic, and electronic elements of a system, as opposed to programs, procedures, rules, XEROX DOCUPRINT 180 LPS MESSAGE GUIDE GLOSSARY-9...
Page 336 Data or text introduced into a computer-based system. input/output General term encompassing the flow of data into and out of a system. input processing Formatting control for the pages of a report. GLOSSARY-10 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 337 (2x scaling), except the logical rules result in superior output. Interpress Xerox standard that defines digital representation of lines for printing. Interpress documents can be printed on any sufficiently powerful printer equipped with Interpress print software.
Page 338 Printout or display of the statements in a program, usually used as a convenience in examining or editing programs. literal Alphanumeric beginning with a letter, optionally including an asterisk, period, colon, or slash, and not enclosed in single quotes. GLOSSARY-12 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 339 In the Xerox printing systems environment, a formatted page that is smaller than the physical page. A logical page is defined by an origin, thus allowing more than one logical page to be placed on a physical page.
Page 340 Printer that forms characters without any strikes of a key or element against the paper. object file Source file converted into machine language (binary code). GLOSSARY-14 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 341 The operating system is always running when the computer is active. Unlike other types of programs, it does not run to an end point and stop. The operating system of a Xerox LPS is referred to as the operating system software (OSS).
Page 342 12-pitch (12 characters per inch) spacing is called elite. 2. The number of page images placed on the xerographic belt during one revolution. The Xerox DocuPrint 180 LPS supports two pitch modes: 7 pitch when paper 9 inches/229 mm long or less is used to print a job, and 3 pitch when paper 9 to 17 inches/229 to 432 mm long is used to print a job.
Page 343 Formal set of conventions governing the format of data and the control of information exchange between two communication devices. purge To delete data from a system. queue List of documents waiting to be processed. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE GLOSSARY-17...
Page 344 Part of a window that allows you to view information extending beyond the window display. SCSI small computer system interface. Accepted standard for connecting peripheral devices to computers. GLOSSARY-18 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 345 The movement of paper through the printer in the direction of the paper width (the shorter side of a sheet of paper). For the Xerox DocuPrint 180 LPS, short-edge feed allows larger sizes of paper (up to 11 by 17 inches/279 by 432 mm) to be printed.
Page 346 Also referred to as the “ESS”. system disk Magnetic disk storage medium, usually of large capacity, that is not removable as opposed to floppy disk or disk packs. GLOSSARY-20 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 347 The number of characters that can be stored on magnetic media, such as how close together data can be recorded. The Xerox LPS may use either 1600 bpi or 6250 bpi density magnetic media. tape drive Input/output device that controls the movement of magnetic storage tape past the read/write head while data is accessed or stored.
Page 348 Height of a typeface, measured from the bottom of its descenders to the top of its ascenders, expressed in points. type style Italic, condensed, bold, and other variations of typeface that form a type family. GLOSSARY-22 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 349 Data protection feature implemented on magnetic media (for example floppy disk, 9-track tape) to prevent stored data from being modified, written over, or erased. x axis Horizontal axis on a forms grid. XEROX DOCUPRINT 180 LPS MESSAGE GUIDE GLOSSARY-23...
Page 350 CD/IG character dispatcher/image generator control module copy modification entry characters per inch central processing unit GLOSSARY-24 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 351 Extended Binary Coded Decimal Interchange Code end of tape electronic publishing electronic subsystem, also referred to as the system controller forms control buffer finishing configuration utility file control parameter forms description language file directory XEROX DOCUPRINT 180 LPS MESSAGE GUIDE GLOSSARY-25...
Page 352 International Business Machines Corporation Interpress font utility image generator image generator module input/output image output module input output terminal, also referred to as “printer” Interpress decomposer IPFONTS Interpress fonts initial program load GLOSSARY-26 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 353 (refers to the 9-track magnetic tape drive; also referred to as “magnetic tape drive”) optical character recognition operator communications subsystem online interface operating system OSDS operating system diagnostic software OSEXEC operating system executive XEROX DOCUPRINT 180 LPS MESSAGE GUIDE GLOSSARY-27...
Page 354 SAFES stand-alone field engineering software software analysis number START command index SCSI small computer system interface SDLC synchronous data link control short-edge feed status file services sequence insert file GLOSSARY-28 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...
Page 355 XCSC Xerox Customer Support Center XDGI Xerox DCF and GDDM Interface XDSS Xerox Documentation and Software Services XICS Xerox Integrated Composition System XJCF Xerox Job Control Facility xerographic mode persistence xerographic mode switching XEROX DOCUPRINT 180 LPS MESSAGE GUIDE GLOSSARY-29...
Page 356 GLOSSARY XPAF, XPF Xerox Printer Access Facility XPMF-VMS Xerox Print Management Facility - VMS Version XPPI Xerox Pen Plotter Interface Xerox Publishing System GLOSSARY-30 XEROX DOCUPRINT 180 LPS MESSAGE GUIDE...

Xerox DocuPrint 180 Message Manual

1 CP (COMPRESS Command) Messages

2 DSR (Disk Save and Restore Command) Messages

3 FD (Forms Compilation) Messages

4 HIP (Host Interface Processor) Messages

5 IFU (Interpress Font Utility) Messages

6 OSS (Operating System Software) Messages

7 PDL (Job Source Library Compilation) Messages

8 PG (PURGE Command) Messages

9 PR (HARDCOPY Graphics Printing Command) Messages

10 PSC (Printer Subsystem Controller Command) Messages

11 11SCALE Command Messages

12 SFS (Status File Services Command) Messages

13 System Verification Error Messages

14 Summary Sheet Error Messages

15 Xerox Docuprint 180 LPS Additional Messages

Xerox Support Services

Quick Links

Related Manuals for Xerox DocuPrint 180

Summary of Contents for Xerox DocuPrint 180

Table of Contents