Tippmann TRIUMPH MARKER LINE Owner's Manual page 11

Assembly (continued from page 17)
GRIP FRAME ASSEMBLY For Model eXT Markers :
1) To Replace the left grip frame half
E
trigger ; trigger spring (yellow)
spring (silver) ; safety
N
nuts are in place in the right grip frame half
G
Install
L
eXT parts
into Grip
I
Frame
S
as follows:
H
Do not operate the
sear tripper assembly
uninstalled as the
solenoid/armature
may pinch you.
2) Place solenoid and
armature into position
in the right receiver.
3) Carefully align and
insert computer board
into slot.
4) Place trigger switch
on two pins of right receiver half.
5) Insert capacitor into slot.
6) Route wires in cutout
areas to lay flat under
solenoid pin and battery and
not be pinched when receiver halves are reassembled.
Visually inspect internal wires for disconnected wire end(s)
7) Insert solenoid pin
8) Insert Magnet in slot below solenoid/armature as shown.
9)To Replace left Grip Frame half:
Double check that all parts are in place as per steps 1-8 above),
are positioned in cutout areas
the solenoid pin moves freely.
Visually inspect internal wires for disconnected wire end(s)
Keep Battery Clip out and carefully place the left Grip Frame half
onto the right Grip Frame half so it fits flush, then insert and tighten the 4
grip screws . Grip Frame assembly is complete. NOTE: You will install
the trigger guard later as instructed on page 21.
: make sure that: (4 pins
; sear pin (black) ; sear
; battery cover nut ; and 2 tank adapter
.
into 2 slots so it moves freely.
so wires are not pinched or sheared and
18 Assembly (continued on page 19)
Assembly (continued from page 18)
TO ASSEMBLE THE RECEIVER: Do not use power tools to disassemble
; or assemble this marker. Hand start screws and bolts and do not over tighten
; sear and strip threaded parts.
1) Insert (Power tube / valve /gas line and tank adapter assembled)
into right receiver half, align power tube and receiver holes.
Loctite 271 sealant on threads of the 2 valve lock bolts
tighten 2 valve lock bolts
2) Insert Ball Latch
3) Slide Front bolt
4) Insert Rear Bolt
for linkage arm
Bolt Plug
5) Insert Linkage Arm
6) Insert Bolt Handle
into back end of receiver.
7) Insert Drive Guide Pin
of rear bolt
it inside of the rear bolt
8) Push Drive Pin/Spring into rear bolt until you can insert other end
into receiver as shown.
9) Insert 2 square nuts
or damage.
TO ASSEMBLE RECEIVER HALVES:
Double Check: that the Front Bolt*
Rear Bolt*
Buffer Washer
1) Carefully install the
wires
left receiver half onto the
right receiver half (make
sure halves fit flush) then
or damage.
insert and tighten 5
receiver screws
2) Start 2 hopper bolts
(tighten later after
installing the hopper).
Be sure all parts are cleaned and o-rings oiled.
(do not over tighten and strip threaded parts.)
.
onto power tube
(o-ring end first) into power tube
at top and notch for sear at bottom.
into Rear Bolt and align hole for bolt handle
into top of Front Bolt
into rear bolt
into Drive Spring
(turn bolt handle until Drive Pin/Spring inserts through
/ bolt plug .
into right receiver half.
, Ball Latch
/ Bolt Plug , Drive Spring*
and 2 square Nuts are in place and (*=oiled).
.
Bolt = 5/8"
Screw = 1/2" + Head
19
E
N
G
L
I
S
H
Put Red
; insert and
.
, with hole
Insert Rear
insertion.
and Rear Bolt .
and place buffer washer
and insert into back
, Linkage Arm* ,
& Drive Guide Pin* ,
Assembly (continued on page 20)