Tippmann TRIUMPH MARKER LINE Owner's Manual page 10

Disassembly / Assembly (continued from page 15)
TO DISASSEMBLE
THE RECEIVER :
E
turn the velocity screw
in until it stops Remove 2
N
feeder neck bolts =(5/
G
8"). Remove 5 receiver
screws with a +head
L
screwdriver and lift the
I
left receiver half off.
TO REMOVE INTERNAL PARTS FROM RIGHT RECEIVER HALF
S
Lift Ball Latch out of right receiver half (Note the ball latch position).
H
Lift the Drive Pin / Spring
and back to remove it from the rear bolt
before the bolt handle will release).
Pin/Spring fits through buffer washer at reassembly).
Pull bolt handle out of rear bolt
Lift Linkage Arm out of front bolt
Slide Front Bolt off of the Power Tube
(Rear Bolt Plug not visible inside Rear Bolt).
rings and if damaged, replace with new ones. Clean and oil the o-rings.
Remove 2 square nuts
reassembly, place 2 Square nuts
TO REMOVE POWER TUBE
the gas line fitting unless it is leaking or you need to replace the valve. If
you should do so you will need some teflon paste or tape to reinstall it.
First, complete Marker Disassembly Instructions on pages 14-16.
To remove the power tube
the two valve lock bolts from the back of the
right-side receiver. NOTE: when installing valve
lock bolts : apply Red Loctite 271 sealant on
the bolts threads and do not over tighten and strip
threaded parts.
Bolt = 5/8"
Screw = 1/2" + Head
up to remove it from the receiver half
(These parts must be removed
Remove Buffer Washer
.
and rear bolt .
and lift out Rear Bolt
Check front/rear bolt o-
from right receiver half. (NOTE: At
into position in right receiver half).
AND VALVE : NOTE: Do not remove
/valve, unscrew
Valve Lock
Bolts
16
Disassembly / Assembly (continued on page 17)
Disassembly / Assembly (continued from page 16)
To remove Valve
the valve use a wrench to slowly unscrew the gas line fitting. Once
the fitting is out, the valve will slide out the back of the power tube. NOTE:
Check the external valve o-ring and if damaged, replace with a new one.
(If the o-ring is damaged your marker will not function correctly.) Clean
all parts and oil the o-ring.
To Reinstall the valve
tube and align the holes of valve and power tube.
tape or paste to gas line
:
with wrench until snug (do not over tighten and strip threaded parts).
NOTE: If tank adapter is attached to gas line, adjust until tank adapter
aligns with bottom of Grip Frame.
(Drive
GRIP FRAME
from the marker as outlined on page 14 to disassemble it).
To disassemble the Grip Frame
holding the two grip frame halves together and carefully lift left half
/
off grip frame
GRIP FRAME ASSEMBLY For Models XL and XT: NOTE: For Model
eXT: go to GRIP FRAME ASSEMBLY For eXT Markers - instructions
on page 18).
1) To Replace the left grip frame half
trigger ; trigger spring (yellow)
spring (black or blue)
nuts are in place in the right grip frame half
2) Carefully place the
left Grip Frame half on so
it fits flush, then insert and
tighten the 4 grip screws
Grip Frame assembly is
complete.
NOTE: You will install the
trigger guard later as
instructed on page 21.
from power tube : If it is necessary to remove
: Insert cleaned and oiled valve into power
fitting threads, slowly screw it into valve
DISASSEMBLY: (The Grip Frame must be removed
: Remove 4 grip screws
.
: make sure that: (4 pins
; sear pin (black)
; safety ; battery cover nut
.
17
E
N
G
L
Apply teflon
I
S
H
;
; sear ; sear
; and 2 tank adapter
.
Assembly (continued on page 18)